April
20
Eg4 6000xp Inverter Battery Install
April
20
1000W 3 Phase Wind Turbine Grid Tie Inverter Limiter DC 22-65V 45-90V SUN WAL
New Grid Tie Inverter for 3 Phase Wind Turbines. Built-in Dump Load Controller – three phase AC input from wind turbine – Single Phase AC to Grid (100V 110V 120V 220V 230V 240V) – Built-in Power Limit Function. About the Input Voltage. DC 22-65V or 45-90V The DC input range of the wind inverter, the test point should be at the DC side of the built-in rectifier of the inverter, but you can calculate from 3 phases of AC output voltage of the wind turbine to get the DC voltage, the formula is Vac = Vdc/1.732. For example, if the DC input voltage range of the inverter is 4590V, then the wind turbine’s output AC range of the should be 45/1.73290/1.732 = AC 26V 52V. The wind inverter must work with 3 phase AC model wind turbine, there should be 3 wires from the wind turbine. Another way, if the wind turbine is used to charge 24v battery, please select 22-65V inverter. If the wind turbine is used to charge 48v battery, and the highest voltage low than 65v, please select 22-65V inverter. If the 48v wind turbine highest voltage over 65v, and low than 90v, please select 45-90V inverter. Advantage Features of the 2G Wind Power Grid Tie Inverter. The 2nd Generation grid tie inverter, new technical, Higher efficiency. Higher MPPT efficiency, Max 99% Multiple intelligent protection to ensure safe use. Directly connect to three phase wind turbine, without regulator Easy to install and easy to operate. The Electric meter will SLOW down. The wind grid tie power inverter can obtain the wind energy from wind turbine, and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. Why our grid tie inverters need limit function? — It is in response to the overwhelming clamor from our customers for a function that can control the amount of power that the grid tie inverters can generate. With this function, the inverters will just generate power that is not larger than the loads’ power even the inverters are connected with big power solar panel array, we call it “limit function”. Because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meter(the one provided by the electricity provider in the area) is not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumer will be charged for power even if it is given to the grid, and this is the problem. Our SUN G2 series grid tie inverters are integrated this limit function, so SUN G2 series inverters can work in limit mode or normal mode(no limit), you can make the configuration on the LCD display. Power Output : 1000W Input AC/DC Voltage Range : 22v 60V or 45V 90V AC Output Voltage Range : 95-140VAC /185-265VAC Output Frequency : 46Hz65Hz Standby Power Consumption. Wind power grid tie inverter —- 1pcs, 2. Dump load resistor —1pcs, 3. AC cable –1pcs , 4. Limiter sensor/clamp / cable —- optional. Q: Can this inverter work if power off? Grid tie inverter will stop to work if the grid is off. Q :Can this inverter be connected in Parallel? A : Yes, the grid tie inverter is stackable. You may connect two or more inverters to one big wind turbine.
April
19
Solar Micro Inverter 600W Grid Tie MPPT Pure Sine Wave DC to AC Waterproof New
IP65 Waterproof Microinverter 600W Solar Grid Tie Micro Inverter for Solar Panel Description This microinverter can efficiently turn sunlight into clean and green power. The IP65 waterproof design and aluminum construction make it last longer. And it has a display that allows you to clearly see the machine in action. Its powerful output efficiently produces electricity for you to use. Application This product is applicable to 30V or 36V solar panels, 36V batteries. It can be used in residential and small commercial environments. It is suitable for various household appliances. It can convert the DC power generated by solar panels into AC power available for household appliances. Solar Micro Inverter 600W Grid Tie MPPT Pure Sine Wave DC to AC Waterproof New. IP65 Waterproof Microinverter 600W Solar Grid Tie Micro Inverter for Solar Panel. This microinverter can efficiently turn sunlight into clean and green power. High-quality Material: The microinverter is made of aluminum alloy, which is durable, corrosion-resistant, and not easy to rust. You can use it for a long time without frequent replacement. Reverse Power Transmission: This item adopts highly efficient reverse power transmission technology, in which the power is transmitted in the reverse direction when in grid-connected output mode, automatically detecting the load in the circuit and giving priority to its use, making the output more efficient in photovoltaic power generation application systems. Maximum Power Point Tracking: A powerful maximum power point tracking algorithm to optimize power harvesting from solar panels that precisely captures and targets the maximum output power point, resulting in a significant increase in power generation. Electrical Isolation: The complete electrical isolation of the machine’s output and input makes the entire power distribution system well insulated and the use of fully isolated boost circuits makes it safer and more reliable to use. Six-fold Protection: The product comes with over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short-circuit protection, and overload protection, so you can use it with confidence. Flexible Installation: This inverter can be stacked in any number of units, forming a single-phase parallel stacking system or easily forming a three-phase system to provide three-phase AC power, which you can install according to your specific needs. Easy Maintenance: Once installed, this machine requires little maintenance and only needs to be cleaned of dust from the PV panels. HD Display: This microinverter is equipped with an LCD display screen to monitor voltage, power, frequency, current, etc. So you can see the machine clearly in operation. Good Waterproof Performance: IP65 waterproof design and aluminum alloy material can effectively prevent rain from eroding the surface, you can use it with confidence. Environmentally Friendly : This micro-inverter converts the direct current generated by the solar panels into alternating current and provides a continuous source of energy that is environmentally friendly and pollution-free. Small Footprint: With dimensions of just 21.35.825cm/8.392.289.84inch, this micro-inverter does not take up much space and can be installed in even small shops. Full Digital Control: The machine adopts full digital control technology, which makes the machine have a strong anti-interference ability, fast computing speed, and a high degree of intelligence. Its powerful functional system can meet your usage needs. It is our pleasure to answer your confusion and questions. Fixed Gasket&Washer: The gasket and washer in the package help you to mount the PV bracket with great ease. Heat Dissipation Holes: The inverter body has multiple heat dissipation holes, which help the machine to dissipate heat and enable it to run smoothly. This product is applicable to 30V or 36V solar panels, 36V batteries. Install the inverter on the bracket of the photovoltaic panel with the screws provided by the machine. Connect the positive and negative poles of the DC connection plug on the photovoltaic board to the DC input terminal of the inverter. Open the waterproof cover of the AC output connector of the inverter and connect the AC cable to the AC waterproof plug. Connect the AC output cable to the AC main cable. Repeat steps 1 to 3, install and connect all inverters. Connect the AC main cable to the utility grid to start your green energy journey. Operating Temperature Range: -40? 60? /-40? 140? VOC Voltage Range: 36-48V. Maximum Output DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Min/Max Startup Voltage: 22-50V. Maximum DC Short Circuit Current: 40A. Maximum Input Operating Current: 27.2A. Peak Output Power: 600W. Rated Output Power: 550W. Rated Output Current: 4.58A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Static MPPT Efficiency: 99.5%. Output Efficiency: 91.2%. Recommended Battery Parameters: 36V/20mah. Gross Weight: 2.48kg/5.47lbs. Net Weight: 1.63kg/3.59lbs. Product Size: 21.35.825cm/8.392.289.84inch. Package Size: 342411.5cm/13.399.454.53inch. 1 AC Connection Cable. Other Accessories for Installation. Please read the operating manual completely before use. And pay particular attention to the safety instructions included. Please note that our products are grid-connected, the AC output port has to be connected to the home grid in order to achieve grid-connected power generation. When the input load is with solar panels, it is important that the VOC voltage is between 30-48V. We recommend that the solar panel is configured for 20% more power than the power of the product. For example, if the product is 600W, the total power of the solar panels should be between 700-750W. When the input load is a battery, we recommend a battery voltage of 36V, which can be connected in series with 3 12V batteries. Please note that the positive and negative polarity should not be reversed when connecting the product. The recommended battery current is36V/20mah for 600W. The input and output voltage of the configuration is within the normal operating voltage range of the product in order for the product to work properly and achieve grid-connected power generation. Please do not dismantle the inverter by non-specialists, only qualified service personnel should repair this product. Please install the inverter in a place with low humidity, good ventilation and cool places to avoid overheating the inverter and remove flammable and explosive materials from the surrounding area. When using this product, avoid children touching and playing with it to avoid electric shock. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Maximum Output DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. 21.35.825cm/8.392.289.84inch.
April
19
OutBack Power SkyBox Hybrid Grid-Tie solar inverter 5.0kW, 48v DC, 120/240v AC
Good Solar power inverter, it was troubleshooted and UI board with LCD identified and removed. Everything else is intact including BOS. If you’re interested in specific parts from that let us know and we’ll try to find right solution.
April
18
1400W Waterproof Solar Micro Inverter Grid Tie MPPT Pure Sine Wave DC to AC 110V
Specification Model: WVC-1400W Color: Silver Material: Aluminium Alloy Power: 1400W Voltage: 110V Plug Type: US Standard Maximum Input DC Voltage: 54V Peak Power Tracking Voltage: 22-45V Operating Voltage Range: 17-50V Min/Max Start-up Voltage: 22-50V Maximum DC Short Circuit Current: 80A Maximum Input Operating Current: 58A Output Peak Power: 1400watt Rated Output Power: 1350watt Rated Output Current: 12.8A Rated Voltage Range: 80-160VAC Rated Frequency Range: 57-62.5Hz Power Factor: >99% Number of Circuit Connections Per String: 3 Static MPPT Efficiency: 99.5% Maximum Output Efficiency: 91.2% Night Time Power Loss. 1400W Waterproof Solar Micro Inverter Grid Tie MPPT Pure Sine Wave DC to AC 110V. Plug Type: US Standard. Maximum Input DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Min/Max Start-up Voltage: 22-50V. Maximum DC Short Circuit Current: 80A. Maximum Input Operating Current: 58A. Output Peak Power: 1400watt. Rated Output Power: 1350watt. Rated Output Current: 12.8A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Number of Circuit Connections Per String: 3. Static MPPT Efficiency: 99.5%. Maximum Output Efficiency: 91.2%. Night Time Power Loss. Operating Temperature Range:? 40? 60? /? 40? 140? Communication Mode: Power Line Carrier. Power Transmission Mode: Reverse Transmission, Load Priority. Gross Weight: 4.2kg/9.26lbs. Net Weight: 3kg/6.61lbs. Product Size: 2137.44cm/8.2714.721.57inch. Package Size: 483512cm/18.913.784.72inch. An inverter can efficiently turn the direct current generated by solar panels into the alternating current used by household appliances. This microinverter makes it easier. Made of fine aluminum alloy, this I. S a wide range of functions, good safety, convenient installation, and high-cost performance. We believe this inverter will not disappoint you. Premium Material: The inverter is made of aluminum alloy, which is durable, corrosion-resistant, and not easy to rust. You can use it for a long time without frequent replacement, and your cost can be saved. High Efficiency: The product adopts a unique circuit design, imported industrial electronic components, isolated high-frequency transformer, and unique MPPT technology, with efficiency greater than 99%, so it can achieve sensitive response and more stable maximum power point locking. Digital Control: The inverter adopts intelligent soft switching technology, high-frequency switching power supply technology, and 32-bit DSP full digital SPWM control technology, making the product strong anti-interference ability, fast operation speed, high intelligence, and a powerful functional system, which can meet the needs of users. Electrical Isolation: The output and input of the system are completely electrically isolated, the insulation performance of the entire power distribution system is good, and the fully isolated booster circuit is safer and more reliable. Good Heat Dissipation Effect: The product adopts a self-cooling system and is designed with heat dissipation holes, which can timely reduce the temperature during operation, reduce potential safety hazards and extend the applicable life of the product. Safety Guard: The inverter has six protection functions: over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short circuit protection, overload protection, etc. Besides, the IP65 waterproof design can prevent rain from eroding its surface, so you can use it with confidence. Easy Maintenance: After the installation of the power station, you don’t need to do maintenance work. After a long period of use, you only need to remove the dust from the photovoltaic panel. Small Footprint: With a size of. 8.271.5714.72inch. The inverter adopts high-frequency telephone, micro processing, and other technologies, so it is smaller, lighter, and won’t occupy too much space. Flexible Installation Mode: During installation, you can stack multiple inverters at will, form a single-phase parallel stacking system, or conveniently form a three-phase system to provide a three-phase AC. At the same time, we also provide a detailed manual and various accessories. You just need to follow the steps to install them. Gasket: The inverter is equipped with two gaskets to help you install the photovoltaic support, making the inverter more stable. Round Corners : The corners of this product are very round, which can effectively reduce your skin scratches during installation or movement. LED Indicator: The product uses an LED indicator, which mainly has two colors: red light and green light. You can master the product situation in time according to the color and flicker of the light, which is very convenient. This product is applicable to 30V or 36V solar panels, or 36V batteries. The inverter can be widely used in residential or commercial areas, power stations, and schools for turning the direct current generated by solar panels into alternating current. Step 1: Install the inverter on the support of the photovoltaic panel with the screws provided by the machine. Step 2: Connect the positive and negative poles of the DC connection plug on the photovoltaic panel to the DC input terminal of the inverter. Step 3: Open the waterproof cover of the AC output interface of the inverter and connect the AC cable to the AC waterproof plug. Step 4: Connect the AC output cable to the AC main cable. Step 5: Repeat steps 1 to 3 to install and connect all inverters. Step 6: Connect the AC main cable to the public grid and start your green energy journey. 1 Solar Grid Tie Micro Inverter. Other Accessories for Installation. Please install the inverter correctly according to the instructions. If you have any questions, please contact the relevant personnel. Please don’t dismantle the machine. Only qualified maintenance personnel can repair the inverter. Please install the inverter in a place with low humidity and good ventilation to avoid overheating the inverter and remove the surrounding inflammable and explosives. When using this inverter, please take good care of your children to prevent them from touching and playing to avoid electric shock. Please note that connected solar panels, batteries, or wind generators DC input DC power supply cable. Please note that this inverter does not have a monitoring function. Please note that our products are grid-connected, the AC output port has to be connected to the home grid in order to achieve grid-connected power generation. When the input load is with solar panels, it is important that the VOC voltage is between 30-48V. We recommend that the solar panel is configured for 20% more power than the power of the product. For example, if the product is 600W, the total power of the solar panels should be between 700-750W. When the input load is a battery, we recommend a battery voltage of 36V, which can be connected in series with 3 12V batteries. Please note that the positive and negative polarity should not be reversed when connecting the product. The recommended battery current is 36V/10mah for 300W, 36V/20mah for 600W, and 36V/40-45mah for 1200W. The input and output voltage of the configuration is within the normal operating voltage range of the product in order for the product to work properly and achieve grid-connected power generation. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Maximum Input DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. Number of Circuit Connections Per String. Reverse Transmission, Load Priority. 2137.44cm/8.2714.721.57inch. 483512cm/18.913.784.72inch.
April
18
Solar Micro Inverter 1200W MPPT Grid Tie Pure Sine Wave DC to AC LCD Waterproof
Solar Micro Inverter 1200W MPPT Grid Tie Pure Sine Wave DC to AC LCD Waterproof. Please install the inverter correctly according to the instructions. If you have any questions, please contact the relevant personnel. Please don’t dismantle the machine. Only qualified maintenance personnel can repair the inverter. Please install the inverter in a place with low humidity and good ventilation to avoid overheating the inverter and remove the surrounding inflammable and explosives. When using this inverter, please take good care of your children to prevent them from touching and playing to avoid electric shock. Please note that our products are grid-connected, the AC output port has to be connected to the home grid in order to achieve grid-connected power generation. When the input load is with solar panels, it is important that the VOC voltage is between 30-48V. We recommend that the solar panel is configured for 20% more power than the power of the product. For example, if the product is 600W, the total power of the solar panels should be between 700-750W. When the input load is a battery, we recommend a battery voltage of 36V, which can be connected in series with 3 12V batteries. Please note that the positive and negative polarity should not be reversed when connecting the product. The recommended battery current is 36V/10mah for 300W, 36V/20mah for 600W, and 36V/40-45mah for 1200W. The input and output voltage of the configuration is within the normal operating voltage range of the product in order for the product to work properly and achieve grid-connected power generation. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order. An inverter can efficiently turn the direct current generated by solar panels into the alternating current used by household appliances. This micro inverter makes it easier. Made of fine aluminum alloy, this IP65 waterproof inverter has a wide range of functions, good safety, convenient installation, and high-cost performance. We believe this inverter will not disappoint you. The inverter is made of aluminum alloy, which is durable, corrosion-resistant, and not easy to rust. You can use it for a long time without frequent replacement, and your cost can be saved. The inverter has built-in high-precision maximum power point tracking, which can optimize the power collection from the solar panel, accurately capture and lock the maximum output power point, and greatly increase power generation to more than 25%. In addition, the efficient power reverse transmission technology can transmit the power that can not be used up to the grid in the reverse direction to other places for use, and the power transmission rate can reach 99.9%. The inverter is equipped with an LCD display screen to monitor voltage, power, frequency, current, etc. So you can see the machine clearly in operation. The inverter adopts intelligent soft switching technology, high-frequency switching power supply technology, and 32-bit DSP full digital SPWM control technology, making the product strong anti-interference ability, fast operation speed, high intelligence, and a powerful functional system, which can meet the needs of users. The output and input of the system are completely electrically isolated, the insulation performance of the entire power distribution system is good, and the fully isolated booster circuit is safer and more reliable. The inverter has six protection functions: over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short circuit protection, overload protection, etc. Besides, the IP65 waterproof design can prevent rain from eroding its surface, so you can use it with confidence. After the installation of the power station, you don’t need to do maintenance work. After a long time, you only need to remove the dust on the photovoltaic panel. Ith a size of 8.2714.721.57inch, the inverter adopts high-frequency telephone, micro processing, and other technologies, so it is smaller, lighter, and won’t occupy too much space. During installation, you can stack multiple inverters at will, form a single-phase parallel stacking. System, or conveniently form a three-phase system to provide a three-phase AC. We have been working hard to provide better service and quality for our customers, which is our goal. If there is any quality problem with our inverters. The inverter is equipped with two gaskets to help you install the photovoltaic support, making th. E inverter more stable. The inverter is provided with heat dissipation holes, which can play a good role in heat dissipation and prolong the service life of the inverter. This product is applicable to 30V or 36V solar panels, 36V batteries. The inverter can be widely used in residential or commercial areas for turning the direct current generated by solar panels into alternating current. Step 1: Install the inverter on the support of the photovoltaic panel with the screws provided by the machine. Step 2: Connect the positive and negative poles of the DC connection plug on the photovoltaic panel to the DC input comic sans ms of the inverter. Step 3: Open the waterproof cover of the AC output interface of the inverter and connect the AC cable to the AC waterproof plug. Step 4: Connect the AC output cable to the AC main cable. Step 5: Repeat steps 1 to 3 to install and connect all inverters. Step 6: Connect the AC main cable to the public grid and start your green energy journey. Plug Type: US Standard. Maximum Input DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Min/Max Start-up Voltage: 22-50VDC. Maximum DC Short Circuit Current: 80A. Maximum Input Operating Current: 54.4A. Peak Power Output: 1200watt. Rated Output Power: 1150watt. Rated Output Current: 9.58A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Max Unit Per Branch Circut: 3pcs(Single-phase). Static MPPT Efficiency: 99.5%. Maximum Output Efficiency: 91.2%. Night Time Power Loss. Ambient Temperature Range:? 40? 60? /? 40? 140? Communication Mode: Power Line Carrier. Power Transmission Mode: Reverse Transmission, Load Priority. Gross Weight: 4.08kg/8.99lbs. Net Weight: 2.88kg/6.35lbs. Product Size: 2137.44cm/8.2714.721.57inch. Package Size: 47.53411.5cm/18.713.394.53inch. Other Accessories for Installation. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Durable MaterialEasy installationCreative Design. 1200W Grid Tie Inverter. 2137.44cm/8.2714.721.57inch. 47.53411.5cm/18.713.394.53inch. MPPT (Maximum Power Point Tracking). Maximum Input DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. Max Unit Per Branch Circut. Reverse Transmission, Load Priority. 10 A or Less.
April
17
MPPT Grid Tie Smart Solar Micro Inverter 700W Grid Tie & DC to AC 110V
Specification Material: Aluminum Alloy Color: Silver Model: XJ-WVC-700W Plug: US Standard Voltage: 110V Maximum Input Power: 2 × 350W Recommended Solar Panel: Power 2 × 350W, Open Circuit Voltage 30-50V Maximum Input DC Voltage: 54V Peak Power Tracking Voltage: 22-45V Operating Voltage Range: 17-50V Minimum/Maximum Starting Voltage: 22-50V Maximum DC Short Circuit Current: 40A Maximum Input Working Current: 30A Output Voltage: 120V Output Peak Power: 700W Rated Output Power: 650Watt Rated Output Current: 6.36A Rated Voltage Range: 80-160VAC Rated Frequency Range: 57-62.5Hz Power factor: >99% Number of Connections Per Series Circuit: 6 (Single-phase) Output Efficiency: 120V Static MPPT Efficiency: 99.5% Maximum Output Efficiency: 91.2% Power Loss at Night. MPPT Grid Tie Smart Solar Micro Inverter 700W Grid Tie & DC to AC 110V. Solar Micro Inverter 700W Grid Tie MPPT Pure Sine Wave DC 22-50V to AC 120V Waterproof IP65. Maximum Input Power: 2 × 350W. Recommended Solar Panel: Power 2 × 350W, Open Circuit Voltage 30-50V. Maximum Input DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Minimum/Maximum Starting Voltage: 22-50V. Maximum DC Short Circuit Current: 40A. Maximum Input Working Current: 30A. Output Peak Power: 700W. Rated Output Power: 650Watt. Rated Output Current: 6.36A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Number of Connections Per Series Circuit: 6 (Single-phase). Static MPPT Efficiency: 99.5%. Maximum Output Efficiency: 91.2%. Power Loss at Night. Operating Temperature Range: – 40? To+60? Heat Dissipation Mode: Self Cooling. Power Grid Disturbance: EN61000-3-2 Safety Regulation EN62109. Grid Detection: DIN VDE 1026 UL1741. Gross Weight: 2.45kg/5.4lbs. Net Weight: 1.8kg/3.96lbs. Package Size: 342411.5cm/13.389.444.52in. Product Size: 21.35.825cm/8.392.289.84in. With a powerful MPPT algorithm and a 99.9% efficient transmission rate, this solar inverter can greatly improve conversion efficiency while providing stable AC power for home appliances. With high-quality materials and multiple protection features, this solar inverter can serve you for a long time. The product’s built-in MPPT Max. Power Point Tracking optimizes power collection from the solar panel and precisely captures and locks the maximum output power point to significantly increase power generation to more than 25%. The 99.9% efficient reverse power transmission technology transmits the power in the reverse direction in grid-connected output mode while automatically detecting the load in the circuit and prioritizing its use, which greatly improves transmission efficiency. Pure Positive Sine Wave. The product uses SPWM to directly generate a pure positive sine wave with good waveform, low distortion, and low noise to make the radio and other communication devices feel better. The inverter dial fast using high-frequency switching power supply technology and 32-bit DSP fully digital SPWM control technology provides the product with excellent. Capability, high-speed computing capability, and intelligence. Inverters can be stacked in parallel with any number of units for both grid-connected use. After the main monitoring system sends the main control signal the inverter receives the main control signal for synchronous output. The whole power distribution system is well insulated and the output of the system is completely electrically isolated from the input, which makes the use safer and more reliable. Over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short-circuit protection, and overload protection protect the safety of use in all aspects. Multiple inverters can be stacked arbitrarily, forming a single-phase parallel stacking system or a three-phase system to provide three-phase AC power conveniently. Flexible installation allows for a wider range of applications. The power station only needs to clean the. On the PV panel regularly after installation, which makes it very convenient and quick. The upgraded miniature design makes the product size only 8.392.289.84 inches and net weight only 3.96 pounds, which makes it easy to carry and install. The solar inverter is made of high-quality aluminum alloy, which is very strong, durable, and. To be able to serve you for a long time. High-quality material and stable structure bring the product IP65 excellent. Performance so that it can effectively group the influence of. And water, and can operate stably outdoors. We aim to provide quality products and services. We will reply and solve the problem for you as soon as possible. Rounded and smooth corners can protect hands from scratches for easy installation and portability. Clear LED Display Lamp. Clear LED display lamp allows you to easily understand the status of the product for operation. This solar inverter is mainly used for power stations, schools, and home grid connections. Step 1: Install the inverter on the bracket of the photovoltaic panel with the screws. Step 2: Connect the positive and negative poles of the DC connection plug on the photovoltaic board to the DC input terminal of the inverter. Step 3: Open the. Cover of the AC output connector of the inverter and connect the AC cable to the AC. Step 4: Connect the AC output cable to the AC main cable. Step 5: Repeat steps 1 to 3, install and connect all inverters. Step 6: Connect the AC main cable to the utility grid to start your green energy journey. 1English User Notes Manual. All Accessories Needed for Installation. Please correctly install the inverter according to the instructions. If you have any questions, please contact the relevant personnel. T allowed to disassemble the machine. Only qualified maintenance personnel can repair the product. Please install the inverter in a place with low humidity and good ventilation to avoid overheating of the inverter, and remove flammable and explosive materials around. When using this product, children should not touch or play to avoid electric shock. Connect the solar panel and the DC input of the battery DC power supply cable. Our product is grid-connected power generation. The AC output port must be connected to the home grid to achieve grid-connected power generation. When using solar photovoltaic panels, the VOC voltage must be between 30-48V. It is recommended that the power configured for the solar panel be greater than 20% of the product power. When using the battery, it is recommended that the battery voltage be 36V, and three 12V batteries can be connected in series. When connecting the product, the positive and negative polarity shall not be reversed. For 300W products, the recommended parameter of the battery is 36V/10mah. For 600W products, it is recommended that the battery parameter be 36V/20mah. 1200W product: it is recommended that the battery parameter be 36V/40-45mah. The customer’s configuration parameters, input, and output voltages are within the normal voltage range of the product so that the product can work normally and realize grid-connected power generation. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Power 2 × 350W. Maximum Input DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. Number of Circuit Connections Per String. Night Time Power Loss. 40? To+60? EN61000-3-2 Safety Regulation EN62109. DIN VDE 1026 UL1741. 21.35.825cm/8.392.289.84in. 342411.5cm/13.389.444.52in.
April
17
MPPT Grid Tie Smart Solar Micro Inverter 1400W Grid Tie & Off-grid DC to AC 110V
Specification Model: WVC-1400W Color: Silver Material: Aluminium Alloy Power: 1400W Voltage: 110V Plug Type: US Standard Maximum Input DC Voltage: 54V Peak Power Tracking Voltage: 22-45V Operating Voltage Range: 17-50V Min/Max Start-up Voltage: 22-50V Maximum DC Short Circuit Current: 80A Maximum Input Operating Current: 58A Output Peak Power: 1400watt Rated Output Power: 1350watt Rated Output Current: 12.8A Rated Voltage Range: 80-160VAC Rated Frequency Range: 57-62.5Hz Power Factor: >99% Number of Circuit Connections Per String: 3 Static MPPT Efficiency: 99.5% Maximum Output Efficiency: 91.2% Night Time Power Loss. MPPT Grid Tie Smart Solar Micro Inverter 1400W Grid Tie & Off-grid DC to AC 110V. Plug Type: US Standard. Maximum Input DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Min/Max Start-up Voltage: 22-50V. Maximum DC Short Circuit Current: 80A. Maximum Input Operating Current: 58A. Output Peak Power: 1400watt. Rated Output Power: 1350watt. Rated Output Current: 12.8A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Number of Circuit Connections Per String: 3. Static MPPT Efficiency: 99.5%. Maximum Output Efficiency: 91.2%. Night Time Power Loss. Operating Temperature Range:? 40? 60? /? 40? 140? Communication Mode: Power Line Carrier. Power Transmission Mode: Reverse Transmission, Load Priority. Gross Weight: 4.2kg/9.26lbs. Net Weight: 3kg/6.61lbs. Product Size: 2137.44cm/8.2714.721.57inch. Package Size: 483512cm/18.913.784.72inch. An inverter can efficiently turn the direct current generated by solar panels into the alternating current used by household appliances. This microinverter makes it easier. Made of fine aluminum alloy, this I. S a wide range of functions, good safety, convenient installation, and high-cost performance. We believe this inverter will not disappoint you. Premium Material: The inverter is made of aluminum alloy, which is durable, corrosion-resistant, and not easy to rust. You can use it for a long time without frequent replacement, and your cost can be saved. High Efficiency: The product adopts a unique circuit design, imported industrial electronic components, isolated high-frequency transformer, and unique MPPT technology, with efficiency greater than 99%, so it can achieve sensitive response and more stable maximum power point locking. Digital Control: The inverter adopts intelligent soft switching technology, high-frequency switching power supply technology, and 32-bit DSP full digital SPWM control technology, making the product strong anti-interference ability, fast operation speed, high intelligence, and a powerful functional system, which can meet the needs of users. Electrical Isolation: The output and input of the system are completely electrically isolated, the insulation performance of the entire power distribution system is good, and the fully isolated booster circuit is safer and more reliable. Good Heat Dissipation Effect: The product adopts a self-cooling system and is designed with heat dissipation holes, which can timely reduce the temperature during operation, reduce potential safety hazards and extend the applicable life of the product. Safety Guard: The inverter has six protection functions: over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short circuit protection, overload protection, etc. Besides, the IP65 waterproof design can prevent rain from eroding its surface, so you can use it with confidence. Easy Maintenance: After the installation of the power station, you don’t need to do maintenance work. After a long period of use, you only need to remove the dust from the photovoltaic panel. Small Footprint: With a size of. 8.271.5714.72inch. The inverter adopts high-frequency telephone, micro processing, and other technologies, so it is smaller, lighter, and won’t occupy too much space. Flexible Installation Mode: During installation, you can stack multiple inverters at will, form a single-phase parallel stacking system, or conveniently form a three-phase system to provide a three-phase AC. At the same time, we also provide a detailed manual and various accessories. You just need to follow the steps to install them. Gasket: The inverter is equipped with two gaskets to help you install the photovoltaic support, making the inverter more stable. Round Corners : The corners of this product are very round, which can effectively reduce your skin scratches during installation or movement. LED Indicator: The product uses an LED indicator, which mainly has two colors: red light and green light. You can master the product situation in time according to the color and flicker of the light, which is very convenient. This product is applicable to 30V or 36V solar panels, or 36V batteries. The inverter can be widely used in residential or commercial areas, power stations, and schools for turning the direct current generated by solar panels into alternating current. Step 1: Install the inverter on the support of the photovoltaic panel with the screws provided by the machine. Step 2: Connect the positive and negative poles of the DC connection plug on the photovoltaic panel to the DC input verdana of the inverter. Step 3: Open the waterproof cover of the AC output interface of the inverter and connect the AC cable to the AC waterproof plug. Step 4: Connect the AC output cable to the AC main cable. Step 5: Repeat steps 1 to 3 to install and connect all inverters. Step 6: Connect the AC main cable to the public grid and start your green energy journey. 1 Solar Grid Tie Micro Inverter. Other Accessories for Installation. Please install the inverter correctly according to the instructions. If you have any questions, please contact the relevant personnel. Please don’t dismantle the machine. Only qualified maintenance personnel can repair the inverter. Please install the inverter in a place with low humidity and good ventilation to avoid overheating the inverter and remove the surrounding inflammable and explosives. When using this inverter, please take good care of your children to prevent them from touching and playing to avoid electric shock. Please note that connected solar panels, batteries, or wind generators DC input DC power supply cable. Please note that this inverter does not have a monitoring function. Please note that our products are grid-connected, the AC output port has to be connected to the home grid in order to achieve grid-connected power generation. When the input load is with solar panels, it is important that the VOC voltage is between 30-48V. We recommend that the solar panel is configured for 20% more power than the power of the product. For example, if the product is 600W, the total power of the solar panels should be between 700-750W. When the input load is a battery, we recommend a battery voltage of 36V, which can be connected in series with 3 12V batteries. Please note that the positive and negative polarity should not be reversed when connecting the product. The recommended battery current is 36V/10mah for 300W, 36V/20mah for 600W, and 36V/40-45mah for 1200W. The input and output voltage of the configuration is within the normal operating voltage range of the product in order for the product to work properly and achieve grid-connected power generation. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Premium Material? Long Service Life? Creative Design? Durable MaterialEasy installationCreative Design. Reverse Power Transmission, Pure Sine Wave, High-quality Material. Maximum Input DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. Number of Circuit Connections Per String. Reverse Transmission, Load Priority. 2137.44cm/8.2714.721.57inch. 483512cm/18.913.784.72inch.
April
16
Solar Micro Inverter 1200W Grid Tie MPPT Pure Sine Wave DC to AC 120V Waterproof
Solar Micro Inverter 1200W Grid Tie MPPT Pure Sine Wave DC to AC 120V Waterproof. Please install the inverter correctly according to the instructions. If you have any questions, please contact the relevant personnel. Please don’t dismantle the machine. Only qualified maintenance personnel can repair the inverter. Please install the inverter in a place with low humidity and good ventilation to avoid overheating the inverter and remove the surrounding inflammable and explosives. When using this inverter, please take good care of your children to prevent them from touching and playing to avoid electric shock. Please note that our products are grid-connected, the AC output port has to be connected to the home grid in order to achieve grid-connected power generation. When the input load is with solar panels, it is important that the VOC voltage is between 30-48V. We recommend that the solar panel is configured for 20% more power than the power of the product. For example, if the product is 600W, the total power of the solar panels should be between 700-750W. When the input load is a battery, we recommend a battery voltage of 36V, which can be connected in series with 3 12V batteries. Please note that the positive and negative polarity should not be reversed when connecting the product. The recommended battery current is 36V/10mah for 300W, 36V/20mah for 600W, and 36V/40-45mah for 1200W. The input and output voltage of the configuration is within the normal operating voltage range of the product in order for the product to work properly and achieve grid-connected power generation. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order. An inverter can efficiently turn the direct current generated by solar panels into the alternating current used by household appliances. This micro inverter makes it easier. Made of fine aluminum alloy, this IP65 waterproof inverter has a wide range of functions, good safety, convenient installation, and high-cost performance. We believe this inverter will not disappoint you. The inverter is made of aluminum alloy, which is durable, corrosion-resistant, and not easy to rust. You can use it for a long time without frequent replacement, and your cost can be saved. The inverter has built-in high-precision maximum power point tracking, which can optimize the power collection from the solar panel, accurately capture and lock the maximum output power point, and greatly increase power generation to more than 25%. In addition, the efficient power reverse transmission technology can transmit the power that can not be used up to the grid in the reverse direction to other places for use, and the power transmission rate can reach 99.9%. The inverter is equipped with an LCD display screen to monitor voltage, power, frequency, current, etc. So you can see the machine clearly in operation. The inverter adopts intelligent soft switching technology, high-frequency switching power supply technology, and 32-bit DSP full digital SPWM control technology, making the product strong anti-interference ability, fast operation speed, high intelligence, and a powerful functional system, which can meet the needs of users. The output and input of the system are completely electrically isolated, the insulation performance of the entire power distribution system is good, and the fully isolated booster circuit is safer and more reliable. The inverter has six protection functions: over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short circuit protection, overload protection, etc. Besides, the IP65 waterproof design can prevent rain from eroding its surface, so you can use it with confidence. After the installation of the power station, you don’t need to do maintenance work. After a long time, you only need to remove the dust on the photovoltaic panel. Ith a size of 8.2714.721.57inch, the inverter adopts high-frequency telephone, micro processing, and other technologies, so it is smaller, lighter, and won’t occupy too much space. During installation, you can stack multiple inverters at will, form a single-phase parallel stacking. System, or conveniently form a three-phase system to provide a three-phase AC. We have been working hard to provide better service and quality for our customers, which is our goal. If there is any quality problem with our inverters. The inverter is equipped with two gaskets to help you install the photovoltaic support, making th. E inverter more stable. The inverter is provided with heat dissipation holes, which can play a good role in heat dissipation and prolong the service life of the inverter. This product is applicable to 30V or 36V solar panels, 36V batteries. The inverter can be widely used in residential or commercial areas for turning the direct current generated by solar panels into alternating current. Step 1: Install the inverter on the support of the photovoltaic panel with the screws provided by the machine. Step 2: Connect the positive and negative poles of the DC connection plug on the photovoltaic panel to the DC input terminal of the inverter. Step 3: Open the waterproof cover of the AC output interface of the inverter and connect the AC cable to the AC waterproof plug. Step 4: Connect the AC output cable to the AC main cable. Step 5: Repeat steps 1 to 3 to install and connect all inverters. Step 6: Connect the AC main cable to the public grid and start your green energy journey. Plug Type: US Standard. Maximum Input DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Min/Max Start-up Voltage: 22-50VDC. Maximum DC Short Circuit Current: 80A. Maximum Input Operating Current: 54.4A. Peak Power Output: 1200watt. Rated Output Power: 1150watt. Rated Output Current: 9.58A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Max Unit Per Branch Circut: 3pcs(Single-phase). Static MPPT Efficiency: 99.5%. Maximum Output Efficiency: 91.2%. Night Time Power Loss. Ambient Temperature Range:? 40? 60? /? 40? 140? Communication Mode: Power Line Carrier. Power Transmission Mode: Reverse Transmission, Load Priority. Gross Weight: 4.08kg/8.99lbs. Net Weight: 2.88kg/6.35lbs. Product Size: 2137.44cm/8.2714.721.57inch. Package Size: 47.53411.5cm/18.713.394.53inch. Other Accessories for Installation. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. 1200W Grid Tie Inverter. MPPT (Maximum Power Point Tracking). Maximum Input DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. Max Unit Per Branch Circut. Reverse Transmission, Load Priority. 2137.44cm/8.2714.721.57inch. 47.53411.5cm/18.713.394.53inch. 10 A or Less.
April
16
Solar Micro Inverter 1200W MPPT Grid Tie Pure Sine Wave DC to AC LCD Waterproof
Description An inverter can efficiently turn the direct current generated by solar panels into the alternating current used by household appliances. This micro inverter makes it easier. Made of fine aluminum alloy, this IP65 waterproof inverter has a wide range of functions, good safety, convenient installation, and high-cost performance. We believe this inverter will not disappoint you. Solar Micro Inverter 1200W MPPT Grid Tie Pure Sine Wave DC to AC LCD Waterproof. An inverter can efficiently turn the direct current generated by solar panels into the alternating current used by household appliances. The inverter is made of aluminum alloy, which is durable, corrosion-resistant, and not easy to rust. You can use it for a long time without frequent replacement, and your cost can be saved. The inverter has built-in high-precision maximum power point tracking, which can optimize the power collection from the solar panel, accurately capture and lock the maximum output power point, and greatly increase power generation to more than 25%. In addition, the efficient power reverse transmission technology can transmit the power that can not be used up to the grid in the reverse direction to other places for use, and the power transmission rate can reach 99.9%. The inverter is equipped with an LCD display screen to monitor voltage, power, frequency, current, etc. So you can see the machine clearly in operation. The inverter adopts intelligent soft switching technology, high-frequency switching power supply technology, and 32-bit DSP full digital SPWM control technology, making the product strong anti-interference ability, fast operation speed, high intelligence, and a powerful functional system, which can meet the needs of users. The output and input of the system are completely electrically isolated, the insulation performance of the entire power distribution system is good, and the fully isolated booster circuit is safer and more reliable. The inverter has six protection functions: over-temperature protection, under-voltage alarm, under-voltage protection, over-voltage protection, short circuit protection, overload protection, etc. Besides, the IP65 waterproof design can prevent rain from eroding its surface, so you can use it with confidence. After the installation of the power station, you don’t need to do maintenance work. After a long time, you only need to remove the dust on the photovoltaic panel. Ith a size of 8.2714.721.57inch, the inverter adopts high-frequency telephone, micro processing, and other technologies, so it is smaller, lighter, and won’t occupy too much space. Flexible Installation Mode : During installation, you can stack multiple inverters at will, form a single-phase parallel stacking. System, or conveniently form a three-phase system to provide a three-phase AC. We have been working hard to provide better service and quality for our customers, which is our goal. If there is any quality problem with our inverters. Gasket: The inverter is equipped with two gaskets to help you install the photovoltaic support, making th. E inverter more stable. The inverter is provided with heat dissipation holes, which can play a good role in heat dissipation and prolong the service life of the inverter. This product is applicable to 30V or 36V solar panels, 36V batteries. The inverter can be widely used in residential or commercial areas for turning the direct current generated by solar panels into alternating current. Step 1: Install the inverter on the support of the photovoltaic panel with the screws provided by the machine. Step 2: Connect the positive and negative poles of the DC connection plug on the photovoltaic panel to the DC input terminal of the inverter. Step 3: Open the waterproof cover of the AC output interface of the inverter and connect the AC cable to the AC waterproof plug. Step 4: Connect the AC output cable to the AC main cable. Step 5: Repeat steps 1 to 3 to install and connect all inverters. Step 6: Connect the AC main cable to the public grid and start your green energy journey. Plug Type: US Standard. Maximum Input DC Voltage: 54V. Peak Power Tracking Voltage: 22-45V. Operating Voltage Range: 17-50V. Min/Max Start-up Voltage: 22-50VDC. Maximum DC Short Circuit Current: 80A. Maximum Input Operating Current: 54.4A. Peak Power Output: 1200watt. Rated Output Power: 1150watt. Rated Output Current: 9.58A. Rated Voltage Range: 80-160VAC. Rated Frequency Range: 57-62.5Hz. Max Unit Per Branch Circut: 3pcs(Single-phase). Static MPPT Efficiency: 99.5%. Maximum Output Efficiency: 91.2%. Night Time Power Loss. Ambient Temperature Range:? 40? 60? /? 40? 140? Communication Mode: Power Line Carrier. Power Transmission Mode: Reverse Transmission, Load Priority. Gross Weight: 4.08kg/8.99lbs. Net Weight: 2.88kg/6.35lbs. Product Size: 2137.44cm/8.2714.721.57inch. Package Size: 47.53411.5cm/18.713.394.53inch. Other Accessories for Installation. Please install the inverter correctly according to the instructions. If you have any questions, please contact the relevant personnel. Please don’t dismantle the machine. Only qualified maintenance personnel can repair the inverter. Please install the inverter in a place with low humidity and good ventilation to avoid overheating the inverter and remove the surrounding inflammable and explosives. When using this inverter, please take good care of your children to prevent them from touching and playing to avoid electric shock. Please note that our products are grid-connected, the AC output port has to be connected to the home grid in order to achieve grid-connected power generation. When the input load is with solar panels, it is important that the VOC voltage is between 30-48V. We recommend that the solar panel is configured for 20% more power than the power of the product. For example, if the product is 600W, the total power of the solar panels should be between 700-750W. When the input load is a battery, we recommend a battery voltage of 36V, which can be connected in series with 3 12V batteries. Please note that the positive and negative polarity should not be reversed when connecting the product. The recommended battery current is 36V/10mah for 300W, 36V/20mah for 600W, and 36V/40-45mah for 1200W. The input and output voltage of the configuration is within the normal operating voltage range of the product in order for the product to work properly and achieve grid-connected power generation. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Durable, Corrosion Resistant, LCD Display. 1200W Grid Tie Inverter. MPPT (Maximum Power Point Tracking). Maximum Input DC Voltage. Peak Power Tracking Voltage. Maximum DC Short Circuit Current. Maximum Input Operating Current. Max Unit Per Branch Circut. Reverse Transmission, Load Priority. 2137.44cm/8.2714.721.57inch. 47.53411.5cm/18.713.394.53inch. 10 A or Less.