2000W on Grid Tie Inverter with Limiter Controller for 3 Phase 48V Wind Turbine

2000W on Grid Tie Inverter with Limiter Controller for 3 Phase 48V Wind Turbine. Max Efficiency:>92% MPPT Efficiency:99%. AC 100V 110V 120V 220V 230V 240V 50hz 60hz. NEW 1000W Wind Power Grid Tie Inverter. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire wind power system. Overload protection, Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD. Input AC/DC Voltage Range. AC Output Voltage Range. 90-130V / 190VAC 260VAC. Dimensions (W x H x D). (1) (2) Dump load resistor connection Terminal. This terminals will connect to the dump load resistor. (3) AC socket, This socket will connect the inverter to the public grid via the AC cable. This terminals will connect to the wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet for this wind inverter. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. Advanced patented technology, MPPT efficiency is higher. High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years. Each inverter need to pass twice testing (20 hours) before leaving factory. Combination of SGPV does not interact. Improving the efficiency of the entire solar power system. No(Follow-up Tracking information will not be generated until the package arrives at the destination country). We will reply you within 24 hours. Feedback is important to us, we will leave positive to our customers. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem.

Category: 2000w | Comments Off

March 23

2000W Wind Turbine On Grid Tie Inverter Pure Sine Wave 45-90VDC 110V/ 220VAC

2000W Wind Turbine On Grid Tie Inverter Pure Sine Wave 45-90VDC – 110V/ 220VAC. Max Efficiency:>92% MPPT Efficiency:99%. DC/3PHASE AC 22-65V/ 45V-90V. AC 100V 110V 120V 220V 230V 240V 50hz 60hz. NEW 1000W Wind Power Grid Tie Inverter. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire solar power system. Overload protection, Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD. Input AC/DC Voltage Range. AC Output Voltage Range. 90-130V / 190VAC 260VAC. Dimensions (W x H x D). (1) (2) Dump load resistor connection Terminal. This terminals will connect to the dump load resistor. (3) AC socket, This socket will connect the inverter to the public grid via the AC cable. This terminals will connect to the wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet for this wind inverter. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. Advanced patented technology, MPPT efficiency is higher. High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years. Each inverter need to pass twice testing (20 hours) before leaving factory. Combination of SGPV does not interact. No(Follow-up Tracking information will not be generated until the package arrives at the destination country). We will reply you within 24 hours. Feedback is important to us, we will leave positive to our customers. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem.

Category: 2000w | Comments Off

April 13

2000W Grid Tie Inverter with Power Limiter MPPT Stackable DC45-90V to AC190-260V

2000W Grid Tie Inverter with Power Limiter MPPT Stackable DC45-90V to AC190-260V. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter, this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Continuous Power Output:1950W Peak Power Output:2000W Input DC Voltage Range:45V 90V Peak power tracking voltage:50V-90V AC Output Voltage Range:190VAC 260VAC Output Frequency:46Hz65Hz Standby Power Consumption. How to use the Inverter? Standard Grid Tie Inverter Model. More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. 5 Battery Discharge Power Mode. 6 Limiter Module Specification. Clamp sensor- Max 100A. Clamp sensor signal- 5v AC max mA. DC signal Cable- 5v DC, max mA. 1 x Solar Grid Inverter with Limiter 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “bayoung-electronic” and is located in this country: CN. This item can be shipped worldwide.

AC Output Voltage Range: 190VAC ~ 260VAC
Brand: Bayoung
Color: Blue
Continuous Power Output: 1950W
Country/Region of Manufacture: China
Input DC Voltage Range: 45V ~ 90V
Model: 2000W Limiter Grid Tie Inverter
MPPT Function: Yes
Output Frequency: 46Hz~65Hz
Output Wave Form: Pure Sine Wave
Peak Power Output: 2000W
Peak power tracking voltage: 50V-90V
Stackable: Yes
System Configuration: Grid-Tie
Voltage: DC45-90V
Wattage: 2000W

Category: 2000w | Comments Off

March 3

2000W 3000W Pure Sine Wave Power Inverter DC 12V to AC 110V With Remote Control

Pure Sine Wave 2000W 3000W Power Inverter DC 12V to 110V Converter LCD Camping. 2000W/3000W Pure Sine Wave Solar Inverter 12V Battery Power. Pure Sine Wave Inverter. Pure sine wave inverter adopts an aluminum alloy shell to resist heat, cold, and corrosion. LCD screen and LED indicators are convenient for users to master the power inverter working promptly. High-quality pure copper inductances filter the waveform and lower the idle power draw, ensure the true pure sine wave AC output, safeguard your equipment. The inverter uses branded big MOSFETs, capacitors, volt transformers with advanced programmed software, and rational hardware design, making a strong driving capacity. The power inverter features a built-in intelligent temperature-controlled cooling fan. When the machine’s internal temperature reaches a certain level, the fan will rotate and effectively reduces the operating temperature. The pure sine wave power inverter applies multiple intelligent security protections to ensure the inverter is fully protected in the process of use so that the electrical appliances will operate stably and safely. This power inverter is designed for equipment that requires careful protection to provide a more stable pure sine wave output. This inverter is built with the universal standard, suitable for power tools, office supplies, household / kitchen appliances. It can be used in the solar and wind system as well. Get your battery charged by solar panel with the solar charge controller. It delivers ultra-clean pure sine wave power, which is the same as the AC grid power supplied by your utility to prevent crashes in computers. It also reduces electromagnetic interference in TV and other sensitive devices. With its compatibility, it improves AC equipment performance with low interference technology. Note: How to choose suitable power inverters for your equipment? If you need the car power inverter to run the resistive loads (like TV, electric cooker, LED light), please choose the inverter with continuous power higher than the appliance’s rated power. If you need the pure sine wave inverter to run the inductive loads(for appliances such as drill, saw, compressor, motor, water pump), please calculate the inverter’s rated power 3 to 7 times higher than the rated power of your appliance. For the pure sine wave inverter, we suggest you use a 150Ah and above battery to power the loads to ensure the best performance. Please do not leave the power inverter in the ON position while your car is off. Disconnect the positive battery terminal before doing any wiring to the inverter. Meet the electricity needs of 99.99 % of products on the market, such as game consoles, car vacuum cleaners, cameras, TVs, mobile phones, refrigerators, DVD players, flood lights or anywhere AC power is required. Our power inverter shell is made of aluminum alloy, which has strong heat dissipation performance and is durable. The aluminum alloy shell can withstand various harsh environments, protect the internal components, and make the inverter safe for long-term use. [Smart air-cooled electric fan]. The cooling fan system makes the car power inverter quite silent when operating and helps reduce heat. The fan will be running faster when the device gets warmer or output power exceeds 60W. Thereby protecting your equipment more effectively. [US sockets and LCD monitors]. Equipped with stable US safety power sockets, intelligently detect your equipment and match the current you need to use. The smart LCD display shows the power consumption anytime, anywhere. You can also control the inverter on and off by pressing and holding the switch for 3 seconds. [Wide range of applications]. The power inverter is a pure sine wave inverter with a wide range of applications. High efficiency, stable sine wave output, high frequency technology, small size, light weight, suitable for various loads. It is widely used in electric fans, electric kettles, hand drills and car travel, camping, long-distance travel, etc. [Pure sine wave inverters]. Pure sine wave inverter can be connected to any common electrical equipment without any interference (such as Weng Weng sound and TV noise). Before using the remote control, it needs to be paired with the inverter; long press the power button of the inverter for 3 seconds, then press the power button of the remote control to complete the setting. Remote control range = 10 meters. Car power Converter Certification: CE/FCC Output power: 2000W/3000W Peak power: 4000W/6000W Overvoltage protection: 12V (15.0V±0.3) Low voltage protection: 12V (10V±0.3) Recovery voltage: 12V (13.2V±0.3) Input voltage: 12V Output voltage: 110V Output frequency: 50Hz /60Hz Output waveform: pure sine wave Conversion efficiency: 90% Overload protection: =130% Overheating Protection: 80°C ± 5°C Display: Smart LCD display Cooling method: Built-in air cooling Size: 36017379mm/40024288mm Weight: 4Kg/7.5Kg Operating temperature: -20°C 40°C Storage temperature: -10°C 40°C. Car Power Inverter Working temperature is -30? Relative humidity 0%-95%, no condensation. Keep the inverter away from water and avoid spilling water on the machine or rising. Do not insert or unplug the plug with wet hands. Keep the inverter in a cool environment, the suitable temperature should be -20°C40°C, avoid direct sunlight and hot vents. Keep the inverter away from places where flammable materials or flammable gas accumulate. Turn off the switch when the machine is not in use. Please turn off the switch before cleaning. 1 x Pure Sine Wave Inverter(with box) 2 x Battery Cables 1 x User Manual 1× Remote control. Please make sure you have a valid account before purchasing. PO Box addresses are not accepted. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “datouboss01″ and is located in this country: US. This item can be shipped to United States, Mexico, Canada.

Power-YK: YK-3000W
Waveform: Pure Sine Wave
Current Output: 10 A or Less
System Configuration: Grid-Tie
Power Source: Solar
Custom Bundle: No
Wattage: 3000-3499 W
Maximum Flow Rate: 0.5 GPM (1.9 L/min) or Less
MPN: 01
Current Type: DC
Voltage: 11-20 V
Connector Type: Amphenol (Helios H4)
Features: LCD Display
Protection Properties: Overcharge Protection, Overcurrent Protection, Overload Protection, Overspeed Protection, Overvoltage Protection, Reverse Current Protection, Reverse Polarity Protection, Reverse Voltage Protection, Safety Circuit Protection, Short Circuit Protection
Maximum Input Power: 501-600 W
Maximum Input Voltage: 11-20 V
Inverter Technology: Battery-Based
Color: Black
Current Rating: 1-5 A
Material: Aluminum alloy
Brand: Unbranded
Type: Charger/Inverter
Model: Pure Sine Wave
Recommended Environment: Indoor/Outdoor
Charging Mode: MPPT (Maximum Power Point Tracking)
Resistance Properties: Abrasion Resistant, Acid Resistant, Antimicrobial Resistant, Chemical Resistant, Childproof
Country/Region of Manufacture: China
Application: Agriculture/Farming, Automotive, Back-up Power, Camping/Hiking, Commercial, Electronics, Home/Garden, Irrigation, Marine, Municipal, Pool, Recreational Vehicle (RV)
Power: Greater Than 2000 W

Category: 2000w | Comments Off

September 29

2000W Grid Tie Solar Inverter Micro Inversor 4 MPPT Solar Panel 230VAC 240V Home

2000W Grid Tie Solar Inverter Micro Inversor 4 MPPT Solar Panel 230VAC 240V Home. This Grid Tie Micro inverter has an unique design for 4 PV panels and it has a remote monitoring system. This 2000W Grid Tie Micro inverter is used in utility-interactive grid-tied applications. This 2000W Grid Tie Micro inverter has an IP67 protection degree and there is a facility for WiFi communication. Micro inverters Maximize PV Energy Production. Each PV module has individual Maximum Peak Power Tracking (MPPT) controls, which ensures that the maximum power is exported to the utility grid regardless of the performance of the other PV modules in the array. When PV modules in the array are affected by shade, dust, orientation, or any situation in which one module under performs compared with the other units, the Micro inverter ensures top performance from the array by maximizing the performance of each module within the array. More Reliable than Centralized or String Inverters. The distributed Micro inverter system ensures that no single point of system failure exists across the PV system. Micro inverters are designed to operate at full power at ambient outdoor temperatures of up to 149? You can install individual PV modules in any combination of Module quantity, orientation, different type and power rate. The Ground wire (PE) of the AC cable is connected to the chassis inside of the Micro inverter, potentially eliminating the installation of grounding wire (check local regulation). Data collection adopts internal wifi, wireless router is needed near the micro inverter. When complete the installation of the micro inverter, configure wireless router with internal Wi-Fi (refer to the Wi-Fi user manual). The data will be uploaded automatically. Users can monitor and manage the micro inverter through corresponding website or APP. Start-Stop voltage – 20-60V. Recommend PV Voc – 33-60V. Max Input Current – 12.5A4. Rated Output Power – 2000W. Rated output current – 230VAC 9.2A. Frequency – 50/60Hz(4565Hz). Static MPPT – 99.00%. CEC Weighted Efficiency – 95%. Self consumption – 50mW. Net Weight(Kg) – 5.3kg. All items will be checked carefully and packaged in good condition before dispatch the product. The arrival time depends on your location. If you are satisfied with our products and services, we must be thankful to you, if you can give us feedback about our products and services. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “vijayas-6205″ and is located in this country: CN. This item can be shipped worldwide.

Color.: Only Inverter
System Configuration: Grid-Tie
Inverter Technology: Microinverter
Current Output: 10 A or Less
Power Source: Solar
Size: 267 * 300 * 42.5 mm
Custom Bundle: No
Wattage: 2000W
Max Input Current: 12.5A*4
Current Type: AC
Voltage: 230V(184-265VAC)
Connector Type: Standard
Features: All Daylight Conditions, Automatic Voltage Detection
Is Smart Device: Yes
Protection Properties: Anti-island Protection
Maximum Input Power: 2000W
Maximum Input Voltage: 20-60V
Color: Gray
Current Rating: 9.2A
Brand: Unbranded
Type: Charger/Inverter
Model: 2000W Grid Tie Solar Inverter
Recommended Environment: Indoor/Outdoor
Charging Mode: MPPT (Maximum Power Point Tracking)
Resistance Properties: Dustproof, Dust Resistant, Heat Resistant
Country/Region of Manufacture: Unknown
Application: Agriculture/Farming, Electronics, Home/Garden
Power: 2000W
Product Line: Grid Tie Solar Inverter

Category: 2000w | Comments Off

September 23

2000W Grid Tie Inverter with Power Limiter MPPT Stackable DC45-90V to AC190-260V

AC Output Voltage Range: 190VAC ~ 260VAC
Brand: Bayoung
Color: Blue
Continuous Power Output: 1950W
Country/Region of Manufacture: China
Input DC Voltage Range: 45V ~ 90V
Model: 2000W Limiter Grid Tie Inverter
MPPT Function: Yes
Output Frequency: 46Hz~65Hz
Output Wave Form: Pure Sine Wave
Peak Power Output: 2000W
Peak power tracking voltage: 50V-90V
Stackable: Yes
System Configuration: Grid-Tie
Voltage: DC45-90V
Wattage: 2000W

Category: 2000w | Comments Off

September 22

2000W Wind Power On Grid Tie Inverter 220V Output Wind Turbine Input 110V Mains

2KW Wind Power Grid-tied Inverter. WWGIT20 is wind power grid-tied controller&inverter integrated machine with MPPT function. It looks concise and can be easily operated. Keep pressing the button for 5s to unload completely. And then recover by pressing it for another 5s. Switch “ON” the brake switch. Brake by over wind speed. It dumps load completely when reached the set wind speed, and recover automatically after working 10mins and wind speed is less than 15m/s. Brake by over rotational Speed. Unload completely when reached the set rotational speed, and recover automatically after 10mins. 85%110% of rated grid voltage. AC output over frequency. AC short circuit protection. Dump load, grid state, wind generator state, faults. Wind rotate speed, wind power, AC output voltage /current/power, and fault code. Dump load dimension(WHD). Dump load net weight. Note: Part of parameters can be adjusted according to customer. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “bayoung-electronic” and is located in this country: CN. This item can be shipped worldwide.

Type: Charger/Inverter
Brand: Bayoung
Application: Agriculture/Farming, Aquaculture, Back-up Power, Camping/Hiking, Commercial, Electronics, Home/Garden
Resistance Properties: Abrasion Resistant, Acid Resistant, Antimicrobial Resistant, Chemical Resistant, Childproof, Child Resistant, Corrosion Resistant, Dustproof
Current Rating: 11-20 A
Inverter Technology: Hybrid
Wattage: 2000-2499 W
Current Type: AC
System Configuration: Grid-Tie
Power Source: Wind
Features: All Daylight Conditions, Automatic Voltage Detection, Brushless Motor, Corrosion Resistant, Daylight Operation, Fixed Guyed, Flexible
Power: 1801-2000 W
Current Output: 10 A or Less
Charging Mode: MPPT (Maximum Power Point Tracking)
Voltage: 200-299 VAC

Category: 2000w | Comments Off

September 13

2000W Grid Tie Solar Inverter 4 MPPT Micro Inversor Solar Panel 230VAC 240V WIFI

2000W Grid Tie Solar Inverter 4 MPPT Micro Inversor Solar Panel 230VAC 240V WIFI. DC input current of 12.5A, adapt to 600W PV module. The Microinverter is used in utility-interactive grid-tied applications, comprised of two key elements: Microinverter Router. If the wireless signal in the area where the microinverter is weak, it is necessary to add a wifi signal booster at a suitable place between the router and the microinverter. This integrated system improves safety; maximizes solar energy harvest;increases system reliability, and simplifies solar system design, installation, maintenance, and management. Microinverters Maximize PV Energy Production. Each PV module has individual Maximum Peak Power Tracking (MPPT) controls, which ensures that the maximum power is exported to the utility grid regardless of the performance of the other PV modules in the array. When PV modules in the array are affected by shade, dust, orientation, or any situation in which one module underperforms compared with the other units, the Microinverter ensures top performance from the array by maximizing the performance of each module within the array. More Reliable than Centralized or String Inverters. The distributed Microinverter system ensures that no single point of system failure exists across the PV system. Microinverters are designed to operate at full power at ambient outdoor temperatures of up to 149? You can install individual PV modules in any combination of Module quantity, orientation, different type and power rate The Ground wire (PE) of the AC cable is connected to the chassis inside of the Microinverter, potentially eliminating the installation of grounding wire (check local regulation). Data collection adopts internal wifi, wireless router is needed near the microinverter. When complete the installation of microinverter, configure wireless router with internal wifi(refer to the wifi user manual). The data will be uploaded automatically. Users can monitor and manage the microinverter through corresponding website or APP. The Microinverters connect with the single-phase grid, and can also use multiple Micro inverters in the form of single-phase grid to achieve three-phase grid. Max units per branch. 267×300×42.5 mm (Without mounting bracket and cable). Compatible with 6072 cell PV modules. Power line / WIFI/Zigbee. DIN VDE 1026 UL1741. Installation Procedures Microinverter System Installation. A PV system using Microinverters is simple to install. Each Microinverter easily mounts on the PV racking, directly beneath the PV module(s). Low voltage DC wires connect from the PV module directly to the Microinverter, eliminating the risk of high DC voltage. Installation MUST comply with local regulations and technical rules. An AC GFCI device should not be used to protect the dedicated circuit to the microinverter even though it is an outside circuit. None of the small GFCI devices (530mA) are designed for back feeding and will be damaged if back feed. In a similar manner, AC AFCIs have not been evaluated for back feeding and may be damaged if back feed with the output of a PV inverter. Perform all electrical installations in accordance with local electrical codes. Be aware that only qualified professionals should install and/or replace Microinverters. Before installing or using an Microinverter, please read all instructions and warnings in the technical documents and on the Microinverter system itself as well as on the PV array. Be aware that installation of this equipment includes the risk of electric shock. Do not touch any live parts in the system, including the PV array, when the system has been connected to the electrical grid. Strongly recommend to install Surge protection Devices in the dedicated meter box. Step 1- Install the AC branch circuit junction box. Install an appropriate junction box at a suitable location on the PV racking system (typically at the end of a branch of modules). Connect the open wire end of the AC cable into the junction box using an appropriate gland or strain relief fitting. Wire the conductors of the AC(230/400Vac): L – red; N – black ;PE – yellow green. Connect the AC branch circuit junction box to the point of utility Interconnection. WARNING: Wiring colour code can be diferent according local regulation, check all the wires of the installaton before connecting to the AC cable to be sure they match. Step 2- Attach the Microinverters to the racking or the PV module frame. Mark the location of the Microinverter on the rack, with respect to the PV module junction box or any other obstructions. Mount one Microinverter at each of these locations using hardware recommended by your module racking vendor. WARNING: Do not place the inverters (including DC and AC connectors) where exposed to the sun, rain or snow, even gap between modules. Allow a minimum of 3/4 1.5cm. Between the roof and the bottom of the Microinverter to allow proper air flow. Step 3 – Connect the microinverters in parallel. Check the Microinverter technical data page 5 for the maximum allowable number of Microinverters on each AC branch circuit. WARNING: DO NOT exceed maximum number of Microinverters in an AC branch circuit, as displayed on the page 5 of this manual. Step 4- Install an AC cable protective end cap at the end of AC cable. Step 5 – Connect Microinverter to the PV Modules. When plugging in the DC cables, if AC already available, the Microinverter should immediately blink red light and will start work within the setting time (default 60 seconds). If AC is not available, the red light will blink 3 times quickly and repeat after one second until AC is connected. Microinverter System Operating Instructions To operate the microinverter PV system: 1. Turn ON the AC circuit breaker on each microinverter AC branch circuit. Turn ON the main utility-grid AC circuit breaker. Your system will start producing power after a one-minute waiting time. The units should start blinking red one minutes after turning on the AC circuit breaker. Then blue led blinking. This means they are producing power normally, the faster blinking of the blue led means more power generated. Configure the internal wifi module according to its user manual. NOTE: When AC power is applied but the microinverter not started up, about 0.1A current and 25VA(W) power for each microinverter may be measured by a power meter. This power is reactive power, not consume from utility grid. There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “rodonite-7″ and is located in this country: CN. This item can be shipped worldwide.

Color: Inverter 5M AC cable
Input Voltage: 20-60V
Output Voltage: 230V(184-265V)
Size: 267 * 300 * 42.5 mm
Model: 8991503531
Country/Region of Manufacture: China
Output Power: 2112W(Maximum)
Output Type: 230V / 184-265
Rated output current: @230VAC 9.2A
Rated Output Power: 2000W
Rated voltage: @230V(184-265VAC)
Recommend PV Voc: 33-60V
Rrequency: 50/60Hz(45~65Hz)
Start-Stop voltage: 20-60V
Static MPPT: 99%
Weight: 5.3kg
System Configuration: Grid-Tie
Certification: CE, FCC, RoHS
DC short current: 16A*4
Dimensions: 267*300*42.5 mm (Without mounting bracket and c…
Is Smart Device: Yes
Is_customized: Yes
Max Input Current: 12.5A*4
Max output: 96.5%
Max output Power: 2112W
MPN: 8991503556
Brand: Unbranded
Max solar panel: 4*600W (max)
Max units per branch: @230V:4PCS
MPPT: 25-55V
Operating temperature: – 40℃ to +65℃
Origin: CN(Origin)
Output Current: 9.2A(Maximum)
Output Frequency: 50/60Hz

Category: 2000w | Comments Off

August 27

2000W Wind Turbine Grid Tie Inverter Input 45-90V AC Output 110V AC with Limiter

2000W Wind Turbine Grid Tie Inverter Input 45-90V AC Output 110V AC w/ Limiter. Max Efficiency:>92% MPPT Efficiency:99%. DC/3PHASE AC 22-65V/ 45V-90V. AC 100V 110V 120V 220V 230V 240V 50hz 60hz. NEW 1000W Wind Power Grid Tie Inverter. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire Wind power system. Overload protection, Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD. Input AC/DC Voltage Range. AC Output Voltage Range. 90-130V / 190VAC 260VAC. Dimensions (W x H x D). (1) (2) Dump load resistor connection Terminal. This terminals will connect to the dump load resistor. (3) AC socket, This socket will connect the inverter to the public grid via the AC cable. This terminals will connect to the wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet for this wind inverter. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. Advanced patented technology, MPPT efficiency is higher. High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years. Each inverter need to pass twice testing (20 hours) before leaving factory. Combination of SGPV does not interact. Improving the efficiency of the entire solar power system. No(Follow-up Tracking information will not be generated until the package arrives at the destination country). We will reply you within 24 hours. Feedback is important to us, we will leave positive to our customers. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “bayoung-electronic” and is located in this country: CN. This item can be shipped worldwide.

Input Voltage: 2000W/45V-96V
Size: 434*196*88mm
Current Rating: 11-20 A
Inverter Technology: Hybrid
Model: GTINVT20
Maximum Input Power: 1801-2000 W
Wattage: 1500-1999 W
Current Type: AC/DC
System Configuration: Grid-Tie
Power Source: Wind
Type: Charger/Inverter
Features: All Daylight Conditions, Automatic Voltage Detection, Brushless Motor, Corrosion Resistant, Daylight Operation, Fixed Guyed, Flexible, Foldable, Freestanding
Color: Blue
Recommended Environment: Outdoor
Protection Properties: Anti-island Protection, Black Current Protection, Discharge Protection, Freeze Protection, Frost Protection, Lightning Protection, Low Voltage Protection, Open Circuit Protection, Overcharge Protection, Overcurrent Protection
Power: 1000 /2000 W
Current Output: 11-19 A
Brand: Bayoung
Application: Agriculture/Farming, Aquaculture, Automotive, Back-up Power, Camping/Hiking, Commercial, Electronics, Home/Garden, Irrigation, Marine
Charging Mode: MPPT (Maximum Power Point Tracking)
Resistance Properties: Abrasion Resistant, Acid Resistant, Antimicrobial Resistant, Chemical Resistant, Childproof, Child Resistant, Corrosion Resistant, Dustproof, Dust Resistant, Fade Resistant
Voltage: 41-50 V

Category: 2000w | Comments Off

August 9

2000W Battery Discharge Power Mode/MPPT Solar Grid Tie Inverter Pure Sine Wave

2000W Battery Discharge Power Mode/MPPT Solar Grid Tie Inverter 2KW with Limiter Sensor DC 45-90V AC 220V 230V 240V PV connected. 2000w Grid Tie Inverter for Solar Panels or Battery. Working well with all kinds of Battery. With internal Limiter / Wi-Fi connection. Input voltage Range : 45V-90V. Output Voltage : 220V 230V 240V. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter, this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Wi-Fi Function for monitor the solar plant on App or Website. Wifi Port for MPPT 2000W NEW SUN Solar Grid Tie Inverter. Input DC Voltage Range. Peak power tracking voltage. AC Output Voltage Range. Dimensions (W x H x D). How to use the Inverter? Standard Grid Tie Inverter Model. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. 2.1 The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. 2.2 The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. 2.3 The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. 3.1 This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. 3.2 External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. 5 Battery Discharge Power Mode. 6 Limiter Module Specification. Clamp sensor- Max 100A. Clamp sensor signal- 5v AC max mA. DC signal Cable- 5v DC, max mA. Max 13mm or 0.51in cable. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “top.creative.shop” and is located in this country: CN. This item can be shipped worldwide.

Features: All Daylight Conditions, Automatic Voltage Detection
Standby Power Consumption: <0.5W
Custom Bundle: No
Protection Properties: Black Current Protection, Discharge Protection, Freeze Protection, Frost Protection, Low Voltage Protection
Wire Gauge: As Show
Power Factor: 0.99
Voltage: 45V ~ 90V
Connector Configuration: As Show
Item Length: As Show
Over Current Protection: Yes
Shipping: Free
Power Source: Solar
Size: 434x196x88 mm
Country/Region of Manufacture: Hong Kong
Material: As Show
Weight ( Kg): 4.6kg
Recommended Environment: Indoor/Outdoor
Anti-Island Protection: Yes
Model: 2021
Maximum Input Voltage: As Show
Output Frequency: 46Hz~65Hz
Charging Mode: MPPT (Maximum Power Point Tracking)
Peak Inverter Efficiency: 92%
Wattage: 1920W
Application: Agriculture/Farming, Aquaculture, Automotive, Back-Up Power, Camping/Hiking, Commercial, Electronics, Home/Garden, Marine
MPPT Function: Yes
Reverse Polarity Protection: Yes
Current Rating: As Show
Current Type: AC/DC
Current Output: As Show
Power: 2000W
Stackable: Yes
Output Wave Form: Pure Sine Wave
System Configuration: Grid-Tie
Maximum Flow Rate: As Show
Resistance Properties: Corrosion Resistant, Dust Resistant, Fade Resistant
Brand: Unbranded
Inverter Technology: Battery-Based
Color: Blue
Total Harmonic Distortion: <5%
Type: Charger/Inverter
Over Temperature Protection: Yes

Category: 2000w | Comments Off

April 2024
M	T	W	T	F	S	S
« Mar
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30