Magnum Me-mgt500 Dual Mc4 Inputs Micro-inverter 500w 240vac Grid Tie Solar Power

MAGNUM ME-MGT500 DUAL MC4 INPUTS MICRO-INVERTER 500W 240VAC GRID TIE SOLAR POWER. Magnum Energy 500 Watt Grid-Tie Microinverter ME-MGT500. Set up your Grid Tie Solar Power System today – and be ready for Battery Backup later! With the Magnum Energy MicroGT 500 Microinverter , you are able to install 2 solar panels per inverter, reducing installation time, and saving on overall system cost. The microinverter has an individual MPPT for each panel, and can handle up to 310 watt panels, with minimal clipping, delivering 250 watts AC per module. And as with any microinverter, the module level electronics mitigate shading issues and increases overall system production and reliability. What’s UNIQUE about the MicroGT 500 Microinverter? With the 2:1 PV Module ratio, you need HALF the amount of inverters required for the job! Daisy-chain connection of microinverters with integrated AC and DC connections – no trunk cables required! (See AC and DC Connection Diagrams in our images). These micros are Storage Ready – AC couple them with Magnum MS-PAE battery based inverter allowing the addition of batteries to your system when you’re ready! Wider active harvesting range for MPPT tracking voltage! Less points of failure, less labor, and less overall cost/watt! Connect up to 14 solar panels per string, using just 7 GT500 Micros (w/a 20A breaker). Works with 60 and 72-cell modules. UL Certified (UL1741) and Rapid Shutdown compliant (NEC690.12). MagWeb GT Communication Unit (optional – but highly recommended) provides unified display of microinverter production, PAE, and battery status. Additional copper grounding wire will be needed, in connection with the Micro GT’s grounding lug, to ground the system. Or a WEEB may be used between the racking and microinverter. AC Branch Connection Cable has female connector at one end and bare wire at other to connect the junction box to the first microinverter. Weatherproof protective endcap for capping the end of the branch circuit on last microinverter. No diversion controller needed for loads – the MicroGT is optimized to taper charge on the batteries, and prevent them from being overcharged. It will slowly back off charging as the battery fills, and turn off when the battery is full. The AC Coupled Support mode is a control method that causes the output frequency of the MS-PAE battery-base inverter to decrease – causing the output power of the Micro GT grid-tie inverter to decrease, in an attempt to maintain the battery voltage around Absorb voltage. The AC output of the MS-PAE battery based inverter should be greater than the potential array AC output. UP TO 50% DISCOUNTS. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other items. Magnum Energy 500 Watt Grid-Tie Microinverter ME-MGT500 Set up your Grid Tie Solar Power System today – and be ready for Battery Backup later! With the Magnum Energy MicroGT 500 Microinverter, you are able to install 2 solar panels per inverter, reducing installation time, and saving on overall system cost. The item “MAGNUM ME-MGT500 DUAL MC4 INPUTS MICRO-INVERTER 500W 240VAC GRID TIE SOLAR POWER” is in sale since Friday, September 15, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “hurricanewindpowercom” and is located in Roanoke, Virginia. This item can be shipped worldwide.

Brand: Magnum Energy
Model: ME-MGT500 Micro-Inverter
MPN: ME-MGT500
Country/Region of Manufacture: United States

Category: magnum | Comments Off

October 31

1200W Grid Tie Inverter 14V-24V DC/110V AC With 3.5LCD&MPPT For 12V Solar Panel

2015 Version With 3.5 LCD Meter & Solar Panel MPPT Function. 1200 Watt Pure Sine Wave Grid Tie Power Inverter. 14V-24V DC Input 95V-130V AC Output 60Hz Frequency. With LCD Meter Charger For 12V(18V VMP) Solar Panel. Difference Between Grid Tie Inverter And Grid Tie Inverter With LCD Meter(2015 version). The LCD meter’s watts is 10000w, it can measure your whole appliance, long time to use and hard to damage. Cooling area is larger 30% than old version, tempreture and fan protection hard to run, can save the power of solar panel, so inverter can use best efficieny. It will bring your life covenient, take you to a green world and enjoy freely! Inverter has mppt function, LED light has different display when inverter is low voltage, working voltage, high voltage. User can know the power states of solar panel through LCD meter as watts, voltage, amps and so on, it’s really a smart inverter. AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. Advantage For Grid Tie. Grid tie inverter is designed for small solar panel energy market, it’s suitable for family enengy system. 14V-24V grid tie inverter suitable for 12v solar panel which rated volt Vmp is about 18V. 28V-48V grid tie inverter suitable for 24v solar panel which rated volt Vmp is about 36V. 52V-88V grid tie inverter suitable for 48v solar panel which rated volt Vmp is about 72V. 102V-158V grid tie inverter suitable for 96v solar panel which rated volt Vmp is about 144V. Do not suitable for wind turbine, pls do not connect wind turbine for the DC source. This inverter can directly use solar panel through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. This inverter only has grid tie inverter function, do not have tranditional inverter function, pls do not connect the battery for 12v dc source, for further questions, pls leave message to ask, tks. The inverter are designed for solar panels energy directly , no need battery! For battery, 24v for dc 14-24v inverter ; 36v for dc 28-48v inverter ;72v for dc 52-88v inverter ; 144v for dc 102-158v inverter ;But please do NOT hook these the inverter to battery banks for a long time , it will burn the inverter up over a period of time. If you want to connect with wind turbine , need connect with a dump load controller 12v for dc 14-24v inverter ; 24v for dc 28-48v inverter ; 36v for dc 52-88v inverter ; 72v for dc 102-158v inverter. This kind micro grid tie inverter, at the beginning its output will go up, but when the inverter inside is hot and temperature is too high, the fan will work, the inverter’s output will reduce or stop work for some seconds, after the inverter become cool, it will auto work again, and its output will go up. Separate the position of Red and Black terminal, would not cause short circuit easy. There are one big ball type fan. Speed is equal to CPU’s 2 times. Life time is CPU’s 5 times. Old version is SMT parts, easy drop. 2015 version is DIP, not easy drop and with long life time. 2015 version have 2 group capacity , total 12 pcs , low impedance. Filter is more effective, heating temperature is lower 15 degree than old version. Old version adopts current and voltage control IC, instability. Microchip from USA, it is very. Reaction speed is 10 times faster, 100 times high precision. Double protect for AC when over voltage, island reaction, and voltage spike. It will protect the inverter quickly when city power instability. Old version: turn off the switch, the vestigial current and voltage in DC side may damage the ac mosfets. 2015 new version: when turn off the switch, it will turn off both Ac and Dc side, cut off IC signal, would not damage the mosfet. When input power have 600w , the efficiency can reach to 90% , fan would not work , high efficiency will lead inside not to fever, can save solar power; when input power reach 1200w , the efficiency will keep on 87.5%. 2015 new version only have 1 bi-color light. Low voltage: red light flash, inverter no work. High voltage: green light always on, inverter no work. Normal work situation: green light flash, higher watt flash faster. For this design you are very clear to know where is the problem if the inverter not work, very easy to know if from your solar panel or inverter. Sometimes, if you are using some heavy appliance like motor, enginee, cause the voltage up down very fast, in this moment, big amp will come into the grid tie inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid tie inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment, the lightining protection can release thousand voltage to protect the inverter not damage. High speed AC fuse. We now provide access to the ac fuse from the outside of the inverter. Each inverter will come our special ac fuse. This will protect the inverter in less than a millisecond to help prevent high voltage. Spikes from feeding back into the circuitry! Grid Tie Power Inverter? When you use solar panel through grid tie inverter, your home power meter will reduce the speed(if you are using other electric appliances), or your home power meter will backward(if you are not use any appliances). The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The inverter IC will monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase will be match the grid’s, and the volume will be higher than the grid’s, then according to our current controlled PWM, to control the output power to the grid. The inverter will puts out power when the home grid is on. Traditional grid tie inverter is the solar panel are connect in series, so if one solar panel did not work or bad efficiency, then the whole system will be effects, but power jack grid tie inverter, you can use every inverter in parallel, in this moment, each inverter has it’s own MPPT, can make every solar panel got the max power. Our grid tie inverter has 3greens light, when the charge fucntion is normal, then this 3lights will turn on, but if there are not dc sources(like in the night, no sun shine or raining day), the red led light will turn on, the inverter will stop to work, in this moment, the inverter will close the door, the home grid power will not back to inverter. When you set up the grid tie inverter. Pls put the AC plug first. After plug into the home ac source. Dont remove the plug anymore. Otherwise it may have hight voltage spikes. Then connect the DC input. When you want remove the grid tie inverter. Please take away the DC input first. Then you can remove the AC plug. Accessary: will including the AC power cord, DC cable will not including! Fast, Reliably and Directly!! Website for ref is. International Buyers Please Note. The item “1200W Grid Tie Inverter 14V-24V DC/110V AC With 3.5LCD&MPPT For 12V Solar Panel” is in sale since Monday, April 13, 2015. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “powerengineryworld2011″ and is located in China. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia.

Brand: Unbranded/Generic
MPN: Does Not Apply
UPC: Does Not Apply

Category: 1200w | Comments Off

October 30

600W withMPPT Waterproof Grid Tie Inverter DC to AC Solar Micro Power Inverter

600W w/MPPT Waterproof Grid Tie Inverter DC to AC Solar Micro Power Inverter. 600W Waterproof Grid Tie inverter, Pure Sine Wave Inverter. DC22-50V to AC110/220V Output, 50HZ/60HZ Auto. With 433MHz Wireless Communication. 2 Meters Three-Core Connection Cable. WVC600W-Plus grid tie micro inverter using IP65 waterproof streamline design, Can effectively prevent rainwater on the surface erosion, Built-in high-performance Maximum Power Point Tracking(MPPT)Function, Better able to track changes in the solar luminosity and control different output power, Effectively capture and collect sunlight. AC electric power transmission using the reverse transmission technology, Is one of our patented technology, The inverter output power can provide load priority use, Extra electricity to the grid, Efficient use of the inverter to the power emitted, Electricity transmission rate of up to 99%. MPPT power automatic tracking. Intelligent monitoring and management. The output output is completely isolated. Recommended using solar panels. 2300W, open circuit voltage 36-50VOC. Solar panel open circuit voltage range. Peak power tracking voltage. Maximum input operating current. Maximum units per branch circuit. Certificate CEC, CE National patent technology. Reverse transfer, load priority. DIN VDE 1026 UL1741. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. We will response in 24 hours. Thank you for your understanding. The item “600W withMPPT Waterproof Grid Tie Inverter DC to AC Solar Micro Power Inverter” is in sale since Tuesday, June 13, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “maihuiyan” and is located in shenzhen. This item can be shipped worldwide.

Brand: Y&H
Model: 600W Waterproof Grid Tie Inverter
MPN: Does Not Apply
Country/Region of Manufacture: China
DC Input Voltage: 22-50VDC
solar panels: 2×300W, open circuit voltage 36-50VOC
Type:: dc to ac inverter
Type1: Pure Sine Wave Inverter
Waterproof Rating: IP65

Category: 600w | Comments Off

October 30

Solar Micro Grid Tie Inverter Newest On The Market Missouri Wind And Solar

Category: solar | Comments Off

October 29

SMA Sunny Boy SB6000TL-US-22 Grid-Tie String Solar Inverter With DC Disconnect

Brand New in box SMA Sunny boy 6000 TL-US-22 With DC Disconect. SMA Sunny Boy 6000TL-US-22 > 6000 Watt 240 Volt Non-Isolated String Inverter with Emergency Power Switch “switch not included”. The new Sunny Boy TL-US line of transformerless inverters features high efficiency and reduced weight along with both ground and arc fault detection per NEC 2011. An input voltage range of 175 VDC to 600 VDC and dual MPPT input dramatically increases module selection and string sizing flexibility as well as better production when parts of the solar array are shaded. A modern graphic display and an integrated DC disconnect switch are included. An optional Secure Power Supply feature enables these inverters to supply up to 12 A at 120VAC to a single outlet for recharging portable devices or a small UPS directly from the PV array. Optional RS485 or Webconnect data modules enable web-based system monitoring with SMA Sunny Portal. These transformerless inverters work with an ungrounded PV array topology so the requirements of NEC 690.35 must be followed, including using PV Wire for exposed array string wiring. Grid Tie – Central. 40° C – 60° C. Dimensions (W x H x D). Inverter: 19.3″ x 20.5″ x 7.3. Disconnect: 7.4″ x 11.7″ x 7.5. Inverter: 60 lbs Disconnect: 8 lbs. Recommended PV Power (STC). Peak Power Tracking Voltage. 210 V – 480 V. 208 VAC: 5200 W 240 VAC: 6000 W. 208 V / 240 V. 208 V: 183 V – 229 V. 240 V: 211 V – 264 V. The Sunny Boy 3000TL-US/4000TL-US/5000TL-US represents the next step in performance for UL certified inverters. Its transformerless design means high efficiency and reduced weight. Maximum power production is derived from wide input voltage and operating temperature ranges. Multiple MPP trackers and OptiTrac Global Peak mitigate the effect of shade and allow for installation at challenging sites. A unique Emergency Power Supply feature provides daytime power even in the event of a grid outage. High performance, flexible design and an innovative feature set make the Sunny Boy TL-US series the first choice among professionals. One of many unique features to the TL-US residential series is its innovative Emergency Power Supply ability. With most grid-tied inverters, when the grid loses power, so does the solar-powered home. SMA’s solution allows daytime energy to be isolated from the grid and be fed directly to the home via a dedicated power socket, providing residents with access to power as long as the PV system generates electricity. As a transformerless inverter, the TL-US residential series is lighter in weight than its transformer-based counterparts, which makes lifting and transporting the new inverter easier than before. A new wall mounting plate features anti-theft security and makes hanging the inverter quick and easy. A simplified DC wiring concept allows the DC Disconnect to be used as a wire raceway, saving labor and materials. Leading monitoring and control solutions. The new TL-US residential line features more than high performance and a large graphic display. The monitoring and control options provide users with an outstanding degree of flexibility. Integrated Zigbee, a wireless communications standard often used for home energy management, and numerous wired options allows for a highly controllable inverter and one that can still be monitored on Sunny Portal from anywhere on the planet via an Internet connection. Whether communicating through Zigbee or SMA’s new wired, plug-and-play WebConnect, installers can find an optimal solution to their monitoring needs. The Sunny Boy 3000TL-US / 4000TL-US / 5000TL-US are transformerless inverters, which means owners and installers benefit from high efficiency and lower weight. A wide input voltage range also means the inverters will produce high amounts of power under a number of conditions. Additionally, transformerless inverters have been shown to be among the safest string inverters on the market. An industry first, the TL-US series has been tested to UL 1741 and UL1699B and is in compliance with the arc fault requirements of NEC 2011. OptiTrac Global Peak, SMA’s shade-tolerant MPP tracking algorithm, quickly adjusts to changes in solar irradiation, which mitigates the effects of shade and results in higher total power output. And, with two MPP trackers, the TL-US series can ably handle roofs with multiple orientations or specific shaded areas. An extended operating temperature range of -40 °F to +140 °F ensures power is produced in all types of climates and for longer periods of time than with most traditional string inverters. What makes these new SMA inverters so exciting? In a pure grid-tie system, when the utility grid goes down, so does your solar array. In the grand scheme of things, this makes sense: imagine if you’re working on the utility grid and you get electrocuted because someone’s solar array is still feeding power into it? On the other hand, it can be a pain to those who’ve invested in solar so they can have power all the time. While this is a great idea, batteries can add an extra layer of complexity to sizing your system. SMA’s TL-US inverter offers another option, allowing you to literally plug your important electronics into an outlet attached to the unit during full daylight. Under what circumstances will the emergency power switch work? If the utility grid is down and you still have full daylight, you can manually flip the switch on the emergency power switch and then plug what you need to power into the attached socket. I’ve heard that this inverter can handle multiple roof orientations. What does this mean and how does it work? From SMA: Traditionally, solar professionals had different ways of dealing with a site containing multiple roof orientations. A string inverter could be used on each roof, a single inverter for both roofs or micro inverters on both roofs. Micro inverters are a good solution since they can take advantage of the module level MPPT to extract the most energy from the losses associated with mismatched roofs. String inverters have been given a back seat to these types of applications because of the perceived mismatch losses that these types of inverters cannot compensate for. SMAs new 3000TL-US/4000TL-US/5000TL-US family will have dual MPPT channels, which will give them the ability to track two different array orientations while reducing the mismatch losses. In fact, you can even use different string lengths on each channel as well as different module types if your design warrants it. Both arrays are processed separately and their outputs combined after the power conversion. This means more harvest from mismatched arrays but with the benefit of using a single string inverter. The item “SMA Sunny Boy SB6000TL-US-22 Grid-Tie String Solar Inverter With DC Disconnect” is in sale since Wednesday, August 30, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “greensolarelectric” and is located in Covelo, California. This item can be shipped to United States.

Brand: SMA
Model: SB6000TL-US-22
MPN: Suny Boy SB6000TL-US-22
Country/Region of Manufacture: United States

Category: sunny | Comments Off

October 29

New Grid Tie Inverters On Grid Off Grid Smart Grid Free Lifetime Web Monitoring

Category: grid | Comments Off

October 28

1000W Solar Grid Tie Inverter with Power Limiter Prevent Extra Power to Grid

1000W solar grid tie inverter with power limiter provent extra power to grid. Pure sine wave output, mppt solar grid tie inverter. 1:System without the Grid Tied Limiter. The grid tied inverter feeds all of the power available from the solar panels(A1) to the AC load. (A2), all excess power is then exported to the Grid(A3). If the grid fails(Grid V=0v)then the grid tied. Inverter will turn off. When the Grid comes back on line the grid tied inverter will export power back. If the grid tied inverter is producing less power than what is required by the AC LOAD then the. Load will be supplemented with the power from the Grid(B1). If the grid tied inverter is producing more power than what is required by the AC LOAD then. The excess power will be exported to the Grid(A3). Power Meters(Except smart meter)are not aware of the direction of power flow. Charge for power in both directions and this is a problem. The Grid Tied Limiter will fix this problem by preventing the export of power to the grid(A3). Displays the Utility Power (grid power), Inverter Power (GTIL power), Utility KWH and Inverter KWH. Two (2 pcs) – Connects the AC output of GTIL to LM. Can be plug in either receptacle. Power per receptacle is 2kw or a total of 4kw GTIL can be plugged in the two receptacles. Output of GTIL can also be directly connected to the grid or through the house convenient outlet. But the LM LCD will no longer display the Inverter Power and Inverter KWH. Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created. By the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. Clamp sensor AC signal input connects the clamp sensor AC signal to the LM module. Limiter Module AC power input- Connects AC power from grid to energize the wattmeter and the Limiter Circuit. Do not connect to AC grid if terminal block is wired or connected to the GRID. Only use when the GTIL. Is remotely located or the user decided to connect the AC output of GTIL to other grid location within the user premises. Terminal Block- AC power to Grid. The AC output of the GTIL is plugged to the LM receptacle in order for the LCD to display the GTIL. Output in watts and KWH. The GTIL output is connected to the Grid through the Terminal Block. Connecting the terminal block to AC grid also powers the wattmeter and limiter circuit. Limiter DC Signal Output, 2 pcs Connects the LM output signal to the GTIL signal input. Can connect to any of the signal output receptacle. We provide 3 connection diagrams for customer to choose. GTIL will only provide 3m signal cable. And sensor signal cable. If customer need to configurate the system same as the diagram 2 and. May cause bigger excess power. We have test it, as long as the cable is less than 30M, It will have no affect. Note: The Grid Tied Limiter cannot able to limit power 100% accurate, It will have some excess. Power send to the grid or supplement by the grid. But in most of the time, it will supplement by grid. The excess power will be about 10W. Models available for Masspower GTIL. 500W Grid Tied Inverter with power limiter Model SUN-500GTIL. 600W Grid Tied Inverter with power limiter Model SUN-600GTIL. 1000W Grid Tied Inverter with power limiter Model SUN-1000GTIL. 1500W Grid Tied Inverter with power limiter Model SUN-1500GTIL. 2000W Grid Tied Inverter with power limiter Model SUN-2000GTIL. Specifications of grid tie inverters. NO LCD available at current price! SGPV(Small Grid Tie Photovoltaic System). The only plug and play small grid tie photovoltaic system. The stackable small grid tie photovoltaic system INTRODUCTION. The small type solar grid tie power inverter can obtain the solar energy from solar panel, and can tie to the grid through its output cable with no extra equipment. The installation is very convenient and reliable. We call the system combining with small solar grid tie power inverter and solar panels as’SGPV’. Solar panels and small type grid tie power inverter. Solar panels can be mono silicon, polygon silicon, non-crystal film or. Any other material that can transform solar energy to electric energy. The power of grid tie inverter should be matched to. The power of solar panels connected. So the power of SGPV is defined by its solar panels, it can be standardization according. To the actual using. The inverter can be connected to any outlet at home, when this line run by the conventional electric network. Tie monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase. Are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to. Control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the sun shines, the PV panel will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage. And puts out power to the home grid. When the total power of electric apparatus that are using in the house is larger than the. Output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter. Otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the. House to the out grid. Advantage of The Sunshine Grid Tie Power System. There are many advantages of SGPV compare with the traditional grid tie power system. Low cost and easy installation – SGPV can make full use of all types of buildings surface that face to the sun in the city as. Well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs. Free combination – SGPV can be used as a separate grid tie system and can be setup as a large solar array with many of them. The quantity of SGPV in the array is just according to your desire. If you are planning to install a grid-tie PV system, in a general way. The solar array and inverter need to be carefully matched to ensure that the inverters voltage and power limits are not exceeded. When you want to increase more solar panels, and if the total power of the solar panels exceeds the allocation grid inverter, it is. Necessary to increase the cost of a grid inverter. Combination of SGPV does not interact – The traditional solar grid tie system, they offer units ranging in high power output and. These units are modular so you can have multiple units operating in parallel for large solar arrays. Although, the traditional grid inverter. Has MPPT feature (Maximum Power Point Tracking), but the maximum power point is according to the entire series in terms of solar. Panels array, if the performance of a piece of solar panels in the system, for some reason, such as leaves, bird droppings, dust, shadow. And degrades, the performance of the entire solar power system will decrease. SGPV has no such disadvantage. Of a piece of solar panels in the system degrades, this just effects this piece itself, will not affect other SGPV in the system. Improving the efficiency of the entire solar power system In traditional grid tie system, the solar panels are connected in series. So the MPPT of the inverter is according to the total panels in series, not to every panel, but there is difference between every panel, so. Not every panel is working at the maximum power, this will reduce the total power of these panel in series. But SGPV has no such disadvantage. Because every inverter of SGPV has MPPT function, so every panel is working at the maximum power, this will increase the efficiency of the. Low power consumption Most of the parts in the small grid-tie inverter are digital ICs and low power MCU, so the power consumption of it is low, though the quantity of grid tie inverters is increased, but this will not increase the power consumption much of the entire system. (only available with inverter with LCD). Electric parameters measurement function (voltage, current and active power, electric energy). Running time function (record load cumulative working hours). Power down data save function (save the number of kWh, operation time). Large screen LCD display (display voltage, current, power, active power, cumulative running time) Key Function. UP: Short press will display power, electricity, current and voltage in anti-sequence. DOWN: Short press will display power, electricity, current and voltage in sequence. BACK LIGHT: Short press will open or close backlight. Normal AC Output Power. Maximum AC Output Power. AC Output Voltage Range. AC Output Frequency Range. Total Harmonic Distortion(THD). DC Input Voltage Range. The item “1000W Solar Grid Tie Inverter with Power Limiter Prevent Extra Power to Grid” is in sale since Tuesday, November 22, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “zcsolar2016″ and is located in , . This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: Tricorpower
MPN: Does Not Apply
Country/Region of Manufacture: China

Category: 1000w | Comments Off

October 28

2 IN 1 ON/OFF 1200W Grid Tie Inverter DC 28V-48V To AC 110V (28-48V Solar Panel)

2 IN 1 ON/OFF. 1200 Watt Pure Sine Wave Grid Tie Power Inverter. 28V-48V DC Input 9. 50Hz & 60Hz Frequency. With 3.5 LCD Meter & Solar Panel MPPT Function. 50A/24V, 1200W Solar Controller. Charger For 24V(36V VMP) Solar Panel. A lof of people are using off grid system, means put solar battery to your battery bank, then take the power to using it, this is good idea, however what happened if your battery bank is full of charge, what happened now for the new solar engery, just let become heat & waste it? You already know need using green energy to protect the earth, but why you waste the green power for not easy to get it(you need hour by hour to get it)why you just let it go? A lof of customers asking what should i do, yes, we hear your voice, now we give you 2 in 1 on/off grid inverter, this will let your green power to battery first, until the battery is full will go to float charging, in this moment, the smart inverter will auto switch to on grid mode, that’s 27.5v, in this moment, your battery already 80% full, as some battery is hard to get more than 80%, in this moment, no need waste power to keep charge your battery, so directly switch to on grid mode. When the battery voltage done to 26.5v, will switch back to off grid mode. This is including 2PCS LCD 3.5 big display, one is showing your solar panel & battery situations. SOLAR OFF/ BTY ON. (this page will clear show you the solar connecting situations). SOLAR ON/ BTY ON. Can clear tell you the solar is correct to connect & battery is on charging. WATT : (will show you how many solar panel coming in). VOLTAGE: (will show you the voltage for your solar panel, laoding voltage). AMP : (will show you how many amp coming into the battery). VOLTAGE : (will show you battery voltage). Capacity : (this you need enter your battery size by your self). Charge tme/F : charge time for full, tell you how long your battery can be full. Total energy: xxx KWH. SET BTY: setting your battery size. SET ETC: setting electricity bill. SET DEL: delete all your total energy & cost. Your solar panel is over voltage. Your battery is low voltage. This has 50A/24V, 1200W SOLAR CONTROLLER on the inverter. INPUT VOLTAGE: 28-48V(For solar panel no load). On grid voltage auto switch: over 27.5v(for your battery). Off grid voltage auto switch: under 26.5v(for your battery). Low battery voltage shut down: 21.5v(for dc output). Auto turn on voltage : 24v(for dc output). Pls make sure you total understand this 2 in 1 function, tks. Difference Between Grid Tie Inverter And Grid Tie Inverter With LCD Meter(2015 version). The LCD meter’s watts is 10000w, it can measure your whole appliance, long time to use and hard to damage. Cooling area is larger 30% than old version, tempreture and fan protection hard to run, can save the power of solar panel, so inverter can use best efficieny. It will bring your life covenient, take you to a green world and enjoy freely! Inverter has mppt function, LED light has different display when inverter is low voltage, working voltage, high voltage. User can know the power states of solar panel through LCD meter as watts, voltage, amps and so on, it’s really a smart inverter. AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. Advantage For Grid Tie Power Inverter. Grid tie inverter is designed for small solar panel energy market, it’s suitable for family enengy system. 14V-24V grid tie inverter suitable for 12v solar panel which rated volt Vmp is about 18V. 28V-48V grid tie inverter suitable for 24v solar panel which rated volt Vmp is about 36V. 52V-88V grid tie inverter suitable for 48v solar panel which rated volt Vmp is about 72V. 102V-158V grid tie inverter suitable for 96v solar panel which rated volt Vmp is about 144V. Do not suitable for wind turbine, pls do not connect wind turbine for the DC source. This inverter can directly use solar panel through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. This inverter only has grid tie inverter function, do not have tranditional inverter function, pls do not connect the battery for dc source, for further questions, pls leave message to ask, tks. The inverter are designed for solar panels energy directly , no need battery! For battery, 24v for dc 14-24v inverter ; 36v for dc 28-48v inverter ;72v for dc 52-88v inverter ; 144v for dc 102-158v inverter ;But please do NOT hook these the inverter to battery banks for a long time , it will burn the inverter up over a period of time. If you want to connect with wind turbine , need connect with a dump load controller 12v for dc 14-24v inverter ; 24v for dc 28-48v inverter ; 36v for dc 52-88v inverter ; 72v for dc 102-158v inverter. This kind micro grid tie inverter, at the beginning its output will go up, but when the inverter inside is hot and temperature is too high, the fan will work, the inverter’s output will reduce or stop work for some seconds, after the inverter become cool, it will auto work again, and its output will go up. Separate the position of Red and Black terminal, would not cause short circuit easy. There are one big ball type fan. Speed is equal to CPU’s 2 times. Life time is CPU’s 5 times. Old version is SMT parts, easy drop. 2015 version is DIP, not easy drop and with long life time. 2015 version have 2 group capacity , total 12 pcs , low impedance. Filter is more effective, heating temperature is lower 15 degree than old version. Old version adopts current and voltage control IC, instability. Microchip from USA, it is very. Reaction speed is 10 times faster, 100 times high precision. Double protect for AC when over voltage, island reaction, and voltage spike. It will protect the inverter quickly when city power instability. Old version: turn off the switch, the vestigial current and voltage in DC side may damage the ac mosfets. 2015 new version: when turn off the switch, it will turn off both Ac and Dc side, cut off IC signal, would not damage the mosfet. When input power have 600w , the efficiency can reach to 90% , fan would not work , high efficiency will lead inside not to fever, can save solar power; when input power reach 1200w , the efficiency will keep on 87.5%. 2015 new version only have 1 bi-color light. Low voltage: red light flash, inverter no work. High voltage: green light always on, inverter no work. Normal work situation: green light flash, higher watt flash faster. For this design you are very clear to know where is the problem if the inverter not work, very easy to know if from your solar panel or inverter. Sometimes, if you are using some heavy appliance like motor, enginee, cause the voltage up down very fast, in this moment, big amp will come into the grid tie inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid tie inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment, the lightining protection can release thousand voltage to protect the inverter not damage. High speed AC fuse. We now provide access to the ac fuse from the outside of the inverter. Each inverter will come our special ac fuse. This will protect the inverter in less than a millisecond to help prevent high voltage. Spikes from feeding back into the circuitry. Operating Principle For Grid Tie Power Inverter? When you use solar panel through grid tie inverter, your home power meter will reduce the speed(if you are using other electric appliances), or your home power meter will backward(if you are not use any appliances). The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The inverter IC will monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase will be match the grid’s, and the volume will be higher than the grid’s, then according to our current controlled PWM, to control the output power to the grid. The inverter will puts out power when the home grid is on. Traditional grid tie inverter is the solar panel are connect in series, so if one solar panel did not work or bad efficiency, then the whole system will be effects, but power jack grid tie inverter, you can use every inverter in parallel, in this moment, each inverter has it’s own MPPT, can make every solar panel got the max power. Our grid tie inverter has 1 green light, when the charge fucntion is normal, then this green light will turn on, but if there are not dc sources(like in the night, no sun shine or raining day), the red led light will turn on, the inverter will stop to work, in this moment, the inverter will close the door, the home grid power will not back to inverter. When you set up the grid tie inverter. Pls put the AC plug first. After plug into the home ac source. Dont remove the plug anymore. Otherwise it may have hight voltage spikes. Then connect the DC input. When you want remove the grid tie inverter. Please take away the DC input first. Then you can remove the AC plug. Accessary: will including the AC power cord, DC cable will not including! Specification: 1200w grid tie power inverter 28v-48v. DC to 110v with LCD meter (with mppt function). DC 28-48v (solar panel). 23-27v red light flash. 28-48v, green flash, more larger output more faster. Over 48v, green light on. Less 23v, no light on and no output. No Load current Draw. Dimensions (L x W x H /cm). Fast, Reliably and Directly!! International Buyers Please Note. If you are satisfied with our product and service, pls kindly leave full stars good feedback for us. The item “2 IN 1 ON/OFF 1200W Grid Tie Inverter DC 28V-48V To AC 110V (28-48V Solar Panel)” is in sale since Saturday, August 22, 2015. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “poweronlinesale2008″ and is located in USA. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.

Brand: Unbranded/Generic
MPN: Does Not Apply
UPC: Does Not Apply

Category: onoff | Comments Off

October 27

2000W Solar on Grid Tie Inverter with Power Limiter, MPPT PV System DC 45-90V

You may also like. 2000W Solar on Grid Tie Inverter with Power Limiter, MPPT PV System DC 45-90V. The grid tie power inverter is the most efficiency and technologically advanced inverter for solar power system. Low cost and easy installation–it can make full use of all types of buildings’ surface that face to the sun in the city as well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs. Free combination — it can be used as a separate grid tie system and can be setup as a large solar array with many of them. Improving the efficiency of the entire solar power system– Because of MPPT function. So every panel is working at the maximum. 2000W Grid Tie Power Inverter. AC Output Voltage Range. AC Output Frequency Range. 51.5x30x15cm(20.3″x11.8″x5.9). Installing Sunshine Grid Tie Power System involves several key steps. Considering the total capacity of the grid tie power system that you need. Choosing applicable solar panels for Sunshine Grid Tie Inverter. Selecting accessory for installation of the Grid Tie Power System. Selecting correct model of Sunshine Grid Tie Inverter. Installing solar panels to suitable place. Installing Sunshine Grid Tie Inverter to suitable place. Connecting Sunshine Grid Tie Power System with cables and connectors. Completing Sunshine installation map and Connecting the PV modules. Goods in stocked in USA, goods will be set by UPS. For USA customers the most important thing is. We strive to serve our customers and resolve any issues. We appreciate the opportunity to correct any issues you have before you leave feedback. Pls visit my store. We appreciate your business and consideration. We are manufacturers and wholesalers of solar panels and renewable energy products. Our solar business has been established since 2002. Our engineers are experienced in solar and related accessories. OEM and ODM services are both available. We would like to be your best supplier in China. Please take our working time into account. We will reply you in time, if you are in our working time. If you don’t receive our reply within one days, We must be out of work. Public holidays in China is not available for message reply. The item “2000W Solar on Grid Tie Inverter with Power Limiter, MPPT PV System DC 45-90V” is in sale since Saturday, July 29, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “ahatools” and is located in Rosemead, California. This item can be shipped worldwide.

Brand: ECO-WORTHY
MPN: ECO-L03020201003-1
DC Input Voltage: 45V~90V
Output Voltage: AC 220V 230V 240V auto
Featured Refinements: MPPT
Internal Limiter: Built-in
UPC: 607052790387

Category: 2000w | Comments Off

October 27

Grid Tie Solar power inverter SolarMax 4200C 3800W

C DC Input Maximum input voltage 600 VDC MPP (maximum power point) range 90… 253 VAC Power Factor > 0.98 Frequency 49.8… 50.2 Hz Harmonic Current Distortion < 3 % Systems Maximum Efficiency 97 % European Efficiency Input voltage: 400 VDC 95,8 % 300 VDC 95,1 % Tare Losses 0 W Ambient Operating Temperature - 20 °C... + 60 °C Humidity 0... 98%, non-condensing Cooling Thermal convection, with optional active cooling fan (ventilator) Protection Type IP54 Topology Transformerless, twin stage (without galvanic isolation) Network monitoring In compliance with to VDE 0126 Fault current monitoring of residual Through network monitoring current for personal and system safety in compliance with VDE 0126 Display Two-Line, 16 Character LCD (Backlighted) Casing Diecast aluminium Weight 16.3 kg Dimensions (WxHxD) 554 x 260 x 190 mm CE-compliance (In compliance with) EN 61000-6-1, EN 61000-6-3, EN 61000-3-2, EN 50178 Certificate TÜV Rheinland TYPE APPROVED T. The item "Grid Tie Solar power inverter SolarMax 4200C 3800W" is in sale since Wednesday, March 01, 2017. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters". The seller is "zeus-technologies" and is located in polikastro, kilkis. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: SolarMax
Model: 4200c
MPN: 47848

Category: grid | Comments Off

October 2017
M	T	W	T	F	S	S
« Sep				Nov »
						1
2	3	4	5	6	7	8
9	10	11	12	13	14	15
16	17	18	19	20	21	22
23	24	25	26	27	28	29
30	31