1200w grid tie power inverter DC 102v-158v / AC 220v+LCD, solar panel MPPT-W

1200W Grid Tie Power Inverter. DC 102V-158V to AC 220V. For Solar Panel MPPT. AC Output watt :0 Watt Max display power 15KW. Can display running power less than 1W. AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hours. 59 minutes to 24 hours to 2500 days. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. Sometimes, if you are using some heavy appliance like motor, engine, cause the voltage up down very fast, in this moment, big amp will come into the grid tie inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid tie inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment, the lightning protection can release thousand voltage to protect the inverter not damage. High speed AC fuse. Now we put ac fuse outside, each inverter will come our special ac fuse, this will be broken 1min/sec, to make sure high voltage spike come in! Power Jack always bring your life convenience, so let’s enjoy the green world! Idea for power jack. The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The inverter IC will monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase will be match the grid’s, and the volume will be higher than the grid’s, then according to our current controlled PWM, to control the output power to the grid. The inverter will puts out power when the home grid is on. Why use power jack grid tie inverter? When you use solar panel through grid tie inverter, your home power meter will reduce the speed(if you are using other electric appliances), or your home power meter will backward(if you are not use any appliances). Difference of power jack grid tie inverter. Traditional grid tie inverter is the solar panel are connect in series, so if one solar panel did not work or bad efficiency, then the whole system will be effects, but power jack grid tie inverter, you can use every inverter in parallel, in this moment, each inverter has it’s own MPPT, can make every solar panel got the max power. Power jack grid tie inverter has green lights, when the charge fucntion is normal, then this green lights will turn on, but if there are not dc sources(like in the night, no sun shine or raining day), the red led light will turn on, the inverter will stop to work, in this moment, the inverter will close the door, the home grid power will not back to inverter. PSWGT-1200- 102 – 158-220. DC 102 -158 Volt(solar panel). No Load current Draw. Dimensions (L x W x H /cm). For DC 28V-48V inverter. 11.5V – 13.5V. Orange light on, fan keep working, but inverter stop working. Green flash faster and more powerful output. The inverter are designed for solar panels energy directly , no need battery and it is better not for wind turbine! Or we can send parts for repair. After 45 days -2 months. If you are dissatisfied for any reason, please donot be quick to leave negative/neutral feedback. The item “1200w grid tie power inverter DC 102v-158v / AC 220v+LCD, solar panel MPPT-W” is in sale since Wednesday, October 17, 2018. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “dr.powerjack” and is located in CA. This item can be shipped to United States.

Brand: Power Jack
MPN: 1.2K-GT-100V/220V+LCD-L

Category: 1200w | Comments Off

November 22

1200W Grid Tie Inverter 102V-158V DC/110V AC With LCD Meter&MPPT For Solar Panel

2015 Version With 3.5 LCD Meter & Solar Panel MPPT Function. 1200 Watt Pure Sine Wave Grid Tie Power Inverter. For 96V(144V VMP) Solar Panel. 50Hz & 60Hz Frequency. Difference Between Grid Tie Inverter And Grid Tie Inverter With LCD Meter(2015 version). The LCD meter’s watts is 10000w, it can measure your whole appliance, long time to use and hard to damage. Cooling area is larger 30% than old version, tempreture and fan protection hard to run, can save the power of solar panel, so inverter can use best efficieny. It will bring your life covenient, take you to a green world and enjoy freely! Inverter has mppt function, LED light has different display when inverter is low voltage, working voltage, high voltage. User can know the power states of solar panel through LCD meter as watts, voltage, amps and so on, it’s really a smart inverter. AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. Advantage For Grid Tie Power Inverter. Grid tie inverter is designed for small solar panel energy market, it’s suitable for family enengy system. 14V-24V grid tie inverter suitable for 12v solar panel which rated volt Vmp is about 18V. 28V-48V grid tie inverter suitable for 24v solar panel which rated volt Vmp is about 36V. 52V-88V grid tie inverter suitable for 48v solar panel which rated volt Vmp is about 72V. 102V-158V grid tie inverter suitable for 96v solar panel which rated volt Vmp is about 144V. Do not suitable for wind turbine, pls do not connect wind turbine for the DC source. This inverter can directly use solar panel through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. This inverter only has grid tie inverter function, do not have tranditional inverter function, pls do not connect the battery for dc source, for further questions, pls leave message to ask, tks. The inverter are designed for solar panels energy directly , no need battery! For battery, 24v for dc 14-24v inverter ; 36v for dc 28-48v inverter ;72v for dc 52-88v inverter ; 144v for dc 102-158v inverter ;But please do NOT hook these the inverter to battery banks for a long time , it will burn the inverter up over a period of time. If you want to connect with wind turbine , need connect with a dump load controller 12v for dc 14-24v inverter ; 24v for dc 28-48v inverter ; 36v for dc 52-88v inverter ; 72v for dc 102-158v inverter. This kind micro grid tie inverter, at the beginning its output will go up, but when the inverter inside is hot and temperature is too high, the fan will work, the inverter’s output will reduce or stop work for some seconds, after the inverter become cool, it will auto work again, and its output will go up. Separate the position of Red and Black terminal, would not cause short circuit easy. There are one big ball type fan. Speed is equal to CPU’s 2 times. Life time is CPU’s 5 times. Old version is SMT parts, easy drop. 2015 version is DIP, not easy drop and with long life time. 2015 version have 2 group capacity , total 12 pcs , low impedance. Filter is more effective, heating temperature is lower 15 degree than old version. Old version adopts current and voltage control IC, instability. Microchip from USA, it is very. Reaction speed is 10 times faster, 100 times high precision. Double protect for AC when over voltage, island reaction, and voltage spike. It will protect the inverter quickly when city power instability. Old version: turn off the switch, the vestigial current and voltage in DC side may damage the ac mosfets. 2015 new version: when turn off the switch, it will turn off both Ac and Dc side, cut off IC signal, would not damage the mosfet. When input power have 600w , the efficiency can reach to 90% , fan would not work , high efficiency will lead inside not to fever, can save solar power; when input power reach 1200w , the efficiency will keep on 87.5%. 2015 new version only have 1 bi-color light. Low voltage: red light flash, inverter no work. High voltage: green light always on, inverter no work. Normal work situation: green light flash, higher watt flash faster. For this design you are very clear to know where is the problem if the inverter not work, very easy to know if from your solar panel or inverter. Sometimes, if you are using some heavy appliance like motor, enginee, cause the voltage up down very fast, in this moment, big amp will come into the grid tie inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid tie inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment, the lightining protection can release thousand voltage to protect the inverter not damage. High speed AC fuse. We now provide access to the ac fuse from the outside of the inverter. Each inverter will come our special ac fuse. This will protect the inverter in less than a millisecond to help prevent high voltage. Spikes from feeding back into the circuitry! Operating Principle For Grid Tie Power Inverter? When you use solar panel through grid tie inverter, your home power meter will reduce the speed(if you are using other electric appliances), or your home power meter will backward(if you are not use any appliances). The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The inverter IC will monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase will be match the grid’s, and the volume will be higher than the grid’s, then according to our current controlled PWM, to control the output power to the grid. The inverter will puts out power when the home grid is on. Traditional grid tie inverter is the solar panel are connect in series, so if one solar panel did not work or bad efficiency, then the whole system will be effects, but power jack grid tie inverter, you can use every inverter in parallel, in this moment, each inverter has it’s own MPPT, can make every solar panel got the max power. Our grid tie inverter has 1 green light, when the charge fucntion is normal, then this green light will turn on, but if there are not dc sources(like in the night, no sun shine or raining day), the red led light will turn on, the inverter will stop to work, in this moment, the inverter will close the door, the home grid power will not back to inverter. When you set up the grid tie inverter. Pls put the AC plug first. After plug into the home ac source. Dont remove the plug anymore. Otherwise it may have hight voltage spikes. Then connect the DC input. When you want remove the grid tie inverter. Please take away the DC input first. Then you can remove the AC plug. Accessary: will including the AC power cord, DC cable will not including! Ast, Reliably and Directly!! International Buyers Please Note. If you are satisfied with our product and service, pls kindly leave full stars good feedback for us. The item “1200W Grid Tie Inverter 102V-158V DC/110V AC With LCD Meter&MPPT For Solar Panel” is in sale since Wednesday, May 06, 2015. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Car Electronics Accessories\Power Inverters”. The seller is “powertheworld2012″ and is located in USA. This item can be shipped to United States, Canada.

Brand: Unbranded/Generic
MPN: Does Not Apply
UPC: Does Not Apply

Category: 1200w | Comments Off

July 12

1200W Grid tie power inverter DC 102V-158V to AC 220V + LCD meter, MPPT for solar

1200W Grid tie power inverter. DC 102V-158V to AC 220V. With 3.5 LCD meter. For solar panel 96V system (best solar panel working voltage 125V135V). AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W) 2. AC Output Volt : 0 volt (Max display volt 270V) 3. AC Output Amp : 0 Amp (Max display amp 55A) 4. Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days 5. Electricity consumption: 01000000 kwh 6. Total operation time , electricity consumption and electricity cost can clear 8. Can set up power , the meter will alarm when reach reserve power 9. Can set up the cost 10. Refresh rate: one time 0.5 seconds 11. Whats new of this. We separated the positions of the Red and Black DC input terminals. This provides for easier connection and makes an accidental short circuit much less likely. There are 2 ball type fans for greater air flow. The CPU lifetime is extended by 5 times the old version’s. PCB board: last version used SMT parts. These are easily dislodged by impacts or thermal expansion. The new version has 2 groups of capacitors, total 12 pieces. The low impedance filter is more efficient, running 27. Cooler than old version. The old version used a current and voltage control IC that had instabilities. The new version uses a new microchip from the USA. It is very stable and the reaction speed is 10 times faster, 100 times more precise. Double protection circuit for AC when there is over voltage, an island reaction, or a voltage spike. This will protect the inverter quickly if there is instability in line power. For the old version, when switch off the inverter, vestigial current and voltage in the DC side could damage the AC mosfets. In the new version, when you turn off it, it will turn off both AC and DC sides and cut off the IC signal. This will prevent any damage to the mosfets. When input power is 600w, the efficiency can reach to 90%, so the fan does not need to run offend. The high efficiency keeps the insides cool and can utilize a greater percentage of your solar power. When input power reach 1200w , the efficiency will stay at or above 87.5%. The new version has only 1 bi-colored light: low voltage: the red light flashes and the inverter will not function. High voltage: the green light always on and the inverter will not function. Normal situation: The led light will be green color flashed; led light will flash fast when power is strong. The inverter are designed for solar panels energy directly , no need battery! For battery, 24V battery for DC 14V-24V inverter; 36V for DC 28V-48V inverter, but please do NOT hook inverter with battery banks for a long time , it will burn the parts of inverter over a period of time. Sometimes, if you are using some heaving appliance like motor, engine, cause the voltage up down very fast, in this moment, big amp will come into the grid inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment the lightning protection can release thousand voltages to protect the inverter not damage. High speed AC fuses. Now we put ac fuse outside, each inverter will come our special ac fuse, this will be broken 1 mini/sec, to make sure high voltage spike come in! Is designed for small solar panel & wind energy market, it’s suitable for family energy system. This inverter can directly use solar panel, wind charger through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. The inverter can be connected to any outlet in the home providing line power. The inverter IC will monitors the voltage, frequency and phase of the home grid, then produce a pure sine wave phase locked to the grid. The voltage will be just enough higher than the grid’s to feed power into the grid, Then using our current controlled PWM we control the output power to the grid. The inverter will put out power when the home grid is on. The inverter will stop feeding power into the grid when the grid is down, for safety and as required by law. Why should you use a grid tie inverter? When you use power from solar panels to supply the inverter, your home power. Meter will run more slowly(if you are using other electric appliances), or your. Home power meter will run backward(if you are not use any appliances). Why should you use a Power Jack grid tie inverter. In traditional grid tie inverters, the solar panels are connect in series so if one solar panel did not work or had poor efficiency or had a blown bypass diode, then the whole system is affected. With Power Jack inverters, you can use all panels in parallel so if one is not working properly, you only lose the output from that one panel. You can also run several Power Jack inverters parallel instead of having one large expensive unit. If you have just one expensive inverter and it fails you produce no power. If you have several smaller units and one fails you still produce power. Each inverter has it’s own MPPT function so you can extract the maximum power from all of your solar panels. When the dc charge function is normal, the inverter supplies power. If there are no dc sources (like at night or a cloudy or rainy day), the inverter will stop attempting to supply power and shut itself off from the power grid to protect itself and lengthen its lifetime. For DC 14V-24V inverter. For DC 28V-48V inverter. For DC 50V-88V inverter. For DC 102V-158V inverter. 11.5V – 13.5V. Orange light on, fan keep working, but inverter stop working. Green flash faster and more powerful output. My solar panels are 210W 5 pcs, should I use 5 panels on one inverter or 4 panels. I live in the USA and we use 110V or 220V at 60 cycles. Should I use 1200W grid tie power inverter DC 14V-24V to AC 220V with LCD power meter for solar or 1200W grid tie inverter DC 28V-48V to AC 110V with LCD meter for my solar panels? Should I run them in set of two and double the voltage to 57.7? I like to set it up where I can get the most out of the inverters and the panels, your comments will be highly appreciated. You can use our 1200W grid tie power inverter DC 28V-48V TO AC 220V 60HZ due to below reasons. Your solar panels no load voltage are 35V, and 28V after loading, then the above DC range is just fit it. You can use 5 pcs solar panel and connect them in parallel(DC voltage will be 28V). Then connect them with 1 unit 1200W grid tie power inverter. Regarding use AC 220V system inverter, most home main AC power is 220V. In United States, then separate to 110V(sockets on wall), so you can connect the inverter to home main power (220V) directly. It is ok to use AC 110V inverter, just plug into any home AC 110V socket, but might lose 5-10% power. Q: how to connect Power Jack grid tie inverter? A: inverters DC side connect with solar panels, then the inverter’s plug just plug into home AC socket, and turn on inverter to start work. It is easy to use and no need to add controller. Q: Can solar panels can be hook in series or in parallel? A: solar panels can be hook in series or in parallel, if solar panels are in same voltage, they can be hook in series or in parallel. But if solar panels not in same voltage, they only can be hook in series, can not hook in parallel. Q: Can your grid tie power inverter can be hook together? A: yes, our grid tie power inverter can be connect in parallel, but must be same version. DC 102-158 Volt(solar panel). No Load current Draw. Dimensions (L x W x H /cm). The item “1200W Grid tie power inverter DC 102V-158V to AC 220V + LCD meter, MPPT for solar” is in sale since Saturday, March 05, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “bloominginverter” and is located in Dong Guan. This item can be shipped worldwide.

Brand: Power jack
Model: 1200W
MPN: does not apply
Country/Region of Manufacture: China

Category: 1200w | Comments Off

April 28

1200W, 2500W Grid Tie Inverter 14V-24V, 28V-48V, 52V-88V, 102V-158V MPPT Solar Panel

2015 Version With 3.5 LCD Meter & Solar Panel MPPT Function. 1200 Watt Pure Sine Wave Grid Tie Power Inverter. For 12V(18V VMP) Solar Panel. 95V-130V AC Output 60Hz Frequency. For 24V(36V VMP) Solar Panel. For 48V(72V VMP) Solar Panel. For 96V(144V VMP) Solar Panel. Difference Between Grid Tie Inverter And Grid Tie Inverter With LCD Meter(2015 version). The LCD meter’s watts is 10000w, it can measure your whole appliance, long time to use and hard to damage. Cooling area is larger 30% than old version, tempreture and fan protection hard to run, can save the power of solar panel, so inverter can use best efficieny. It will bring your life covenient, take you to a green world and enjoy freely! Inverter has mppt function, LED light has different display when inverter is low voltage, working voltage, high voltage. User can know the power states of solar panel through LCD meter as watts, voltage, amps and so on, it’s really a smart inverter. AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. 2015 Version With MPPT Function. 2500 Watt Pure Sine Wave Grid Tie Power Inverter. 28V-48V DC Input For 24V(36V VMP) Solar Panel. 52V-88V DC Input For 48V(72V VMP) Solar Panel. Advantage For Grid Tie Power Inverter. Grid tie inverter is designed for small solar panel energy market, it’s suitable for family enengy system. 14V-24V grid tie inverter suitable for 12v solar panel which rated volt Vmp is about 18V. 28V-48V grid tie inverter suitable for 24v solar panel which rated volt Vmp is about 36V. 52V-88V grid tie inverter suitable for 48v solar panel which rated volt Vmp is about 72V. 102V-158V grid tie inverter suitable for 96v solar panel which rated volt Vmp is about 144V. Do not suitable for wind turbine, pls do not connect wind turbine for the DC source. This inverter can directly use solar panel through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. This inverter only has grid tie inverter function, do not have tranditional inverter function, pls do not connect the battery for dc source, for further questions, pls leave message to ask, tks. The inverter are designed for solar panels energy directly , no need battery! For battery, 24v for dc 14-24v inverter ; 36v for dc 28-48v inverter ;72v for dc 52-88v inverter ; 144v for dc 102-158v inverter ;But please do NOT hook these the inverter to battery banks for a long time , it will burn the inverter up over a period of time. If you want to connect with wind turbine , need connect with a dump load controller 12v for dc 14-24v inverter ; 24v for dc 28-48v inverter ; 36v for dc 52-88v inverter ; 72v for dc 102-158v inverter. This kind micro grid tie inverter, at the beginning its output will go up, but when the inverter inside is hot and temperature is too high, the fan will work, the inverter’s output will reduce or stop work for some seconds, after the inverter become cool, it will auto work again, and its output will go up. Separate the position of Red and Black terminal, would not cause short circuit easy. There are one big ball type fan. Speed is equal to CPU’s 2 times. Life time is CPU’s 5 times. Old version is SMT parts, easy drop. 2015 version is DIP, not easy drop and with long life time. 2015 version have 2 group capacity , total 12 pcs , low impedance. Filter is more effective, heating temperature is lower 15 degree than old version. Old version adopts current and voltage control IC, instability. Microchip from USA, it is very. Reaction speed is 10 times faster, 100 times high precision. Double protect for AC when over voltage, island reaction, and voltage spike. It will protect the inverter quickly when city power instability. Old version: turn off the switch, the vestigial current and voltage in DC side may damage the ac mosfets. 2015 new version: when turn off the switch, it will turn off both Ac and Dc side, cut off IC signal, would not damage the mosfet. When input power have 600w , the efficiency can reach to 90% , fan would not work , high efficiency will lead inside not to fever, can save solar power; when input power reach 1200w , the efficiency will keep on 87.5%. 2015 new version only have 1 bi-color light. Low voltage: red light flash, inverter no work. High voltage: green light always on, inverter no work. Normal work situation: green light flash, higher watt flash faster. For this design you are very clear to know where is the problem if the inverter not work, very easy to know if from your solar panel or inverter. Sometimes, if you are using some heavy appliance like motor, enginee, cause the voltage up down very fast, in this moment, big amp will come into the grid tie inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid tie inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment, the lightining protection can release thousand voltage to protect the inverter not damage. High speed AC fuse. We now provide access to the ac fuse from the outside of the inverter. Each inverter will come our special ac fuse. This will protect the inverter in less than a millisecond to help prevent high voltage. Spikes from feeding back into the circuitry! Operating Principle For Grid Tie Power Inverter? When you use solar panel through grid tie inverter, your home power meter will reduce the speed(if you are using other electric appliances), or your home power meter will backward(if you are not use any appliances). The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The inverter IC will monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase will be match the grid’s, and the volume will be higher than the grid’s, then according to our current controlled PWM, to control the output power to the grid. The inverter will puts out power when the home grid is on. Traditional grid tie inverter is the solar panel are connect in series, so if one solar panel did not work or bad efficiency, then the whole system will be effects, but power jack grid tie inverter, you can use every inverter in parallel, in this moment, each inverter has it’s own MPPT, can make every solar panel got the max power. Our grid tie inverter has 1 green light, when the charge fucntion is normal, then this green light will turn on, but if there are not dc sources(like in the night, no sun shine or raining day), the red led light will turn on, the inverter will stop to work, in this moment, the inverter will close the door, the home grid power will not back to inverter. When you set up the grid tie inverter. Pls put the AC plug first. After plug into the home ac source. Dont remove the plug anymore. Otherwise it may have hight voltage spikes. Then connect the DC input. When you want remove the grid tie inverter. Please take away the DC input first. Then you can remove the AC plug. Accessary: will including the AC power cord, DC cable will not including! Fast, Reliably and Directly!! International Buyers Please Note. If you are satisfied with our product and service, pls kindly leave full stars good feedback for us. The item “1200W, 2500W Grid Tie Inverter 14V-24V, 28V-48V, 52V-88V, 102V-158V MPPT Solar Panel” is in sale since Tuesday, March 24, 2015. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “poweronlinesale2008″ and is located in USA. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Dominican republic, El salvador.

Brand: Unbranded/Generic
MPN: Does Not Apply
UPC: Does not apply

Category: 1200w | Comments Off

January 19

1200W Grid tie power inverter DC 102V-158V to AC 220V + LCD, MPPT for solar

2014 6.0 new. 1200W Grid tie power inverter. DC 102V-158V to AC 220V. With 3.5 LCD meter. For solar panel 96V system (best solar panel working voltage 125V135V). AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. Whats new of 2014 6.0 version? We separated the positions of the Red and Black DC input terminals. This provides for easier connection and makes an accidental short circuit much less likely. There are 2 ball type fans for greater air flow. The CPU lifetime is extended by 5 times the old version’s. PCB board: last version used SMT parts. These are easily dislodged by impacts or thermal expansion. The new version has 2 groups of capacitors, total 12 pieces. The low impedance filter is more efficient, running 27. Cooler than old version. The old version used a current and voltage control IC that had instabilities. The new version uses a new microchip from the USA. It is very stable and the reaction speed is 10 times faster, 100 times more precise. Double protection circuit for AC when there is over voltage, an island reaction, or a voltage spike. This will protect the inverter quickly if there is instability in line power. For the old version, when switch off the inverter, vestigial current and voltage in the DC side could damage the AC mosfets. In the new version, when you turn off it, it will turn off both AC and DC sides and cut off the IC signal. This will prevent any damage to the mosfets. When input power is 600w, the efficiency can reach to 90%, so the fan does not need to run offend. The high efficiency keeps the insides cool and can utilize a greater percentage of your solar power. When input power reach 1200w , the efficiency will stay at or above 87.5%. The new version has only 1 bi-colored light: low voltage: the red light flashes and the inverter will not function. High voltage: the green light always on and the inverter will not function. Normal situation: The led light will be green color flashed; led light will flash fast when power is strong. PSWGT-1200-102-158-220 + LCD meter. DC 102-158 Volt (solar panel). No Load current Draw. 55 C ± 5. Dimensions (L x W x H /cm). 43 22 8 CM. The inverter are designed for solar panels energy directly , no need battery! For battery, 24V battery for DC 14V-24V inverter; 36V for DC 28V-48V inverter, but please do NOT hook inverter with battery banks for a long time , it will burn the parts of inverter over a period of time. Sometimes, if you are using some heaving appliance like motor, engine, cause the voltage up down very fast, in this moment, big amp will come into the grid inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment the lightning protection can release thousand voltages to protect the inverter not damage. High speed AC fuses. Now we put ac fuse outside, each inverter will come our special ac fuse, this will be broken 1 mini/sec, to make sure high voltage spike come in! Is designed for small solar panel & wind energy market, it’s suitable for family energy system. This inverter can directly use solar panel, wind charger through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. The inverter can be connected to any outlet in the home providing line power. The inverter IC will monitors the voltage, frequency and phase of the home grid, then produce a pure sine wave phase locked to the grid. The voltage will be just enough higher than the grid’s to feed power into the grid, Then using our current controlled PWM we control the output power to the grid. The inverter will put out power when the home grid is on. The inverter will stop feeding power into the grid when the grid is down, for safety and as required by law. Why should you use a grid tie inverter? When you use power from solar panels to supply the inverter, your home power. Meter will run more slowly(if you are using other electric appliances), or your. Home power meter will run backward(if you are not use any appliances). Why should you use a Power Jack grid tie inverter. In traditional grid tie inverters, the solar panels are connect in series so if one solar panel did not work or had poor efficiency or had a blown bypass diode, then the whole system is affected. With Power Jack inverters, you can use all panels in parallel so if one is not working properly, you only lose the output from that one panel. You can also run several Power Jack inverters parallel instead of having one large expensive unit. If you have just one expensive inverter and it fails you produce no power. If you have several smaller units and one fails you still produce power. Each inverter has it’s own MPPT function so you can extract the maximum power from all of your solar panels. When the dc charge function is normal, the inverter supplies power. If there are no dc sources (like at night or a cloudy or rainy day), the inverter will stop attempting to supply power and shut itself off from the power grid to protect itself and lengthen its lifetime. For DC 14V-24V inverter. For DC 28V-48V inverter. For DC 50V-88V inverter. For DC 102V-158V inverter. 11.5V – 13.5V. Orange light on, fan keep working, but inverter stop working. Green flash faster and more powerful output. Manufacture defects or workmanship, use appropriately, surface of item do not scratch. Manufacture defects or workmanship excludes damage caused by inappropriately used such as improper installation, accident, misuse, abuse, improper storage, or any unauthorized disassembly, repair, or modification. My solar panels are 210W 5 pcs, should I use 5 panels on one inverter or 4 panels. I live in the USA and we use 110V or 220V at 60 cycles. Should I use 1200W grid tie power inverter DC 14V-24V to AC 220V with LCD power meter for solar or 1200W grid tie inverter DC 28V-48V to AC 110V with LCD meter for my solar panels? Should I run them in set of two and double the voltage to 57.7? I like to set it up where I can get the most out of the inverters and the panels, your comments will be highly appreciated. You can use our 1200W grid tie power inverter DC 28V-48V TO AC 220V 60HZ due to below reasons. Your solar panels no load voltage are 35V, and 28V after loading, then the above DC range is just fit it. You can use 5 pcs solar panel and connect them in parallel(DC voltage will be 28V). Then connect them with 1 unit 1200W grid tie power inverter. Regarding use AC 220V system inverter, most home main AC power is 220V. In United States, then separate to 110V(sockets on wall), so you can connect the inverter to home main power (220V) directly. It is ok to use AC 110V inverter, just plug into any home AC 110V socket, but might lose 5-10% power. Q: how to connect Power Jack grid tie inverter? A: inverters DC side connect with solar panels, then the inverter’s plug just plug into home AC socket, and turn on inverter to start work. It is easy to use and no need to add controller. Q: Can solar panels can be hook in series or in parallel? A: solar panels can be hook in series or in parallel, if solar panels are in same voltage, they can be hook in series or in parallel. But if solar panels not in same voltage, they only can be hook in series, can not hook in parallel. Q: Can your grid tie power inverter can be hook together? A: yes, our grid tie power inverter can be connect in parallel, but must be same version. The item “1200W Grid tie power inverter DC 102V-158V to AC 220V + LCD, MPPT for solar” is in sale since Tuesday, February 23, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “6apex_2012″ and is located in Rowland Heights, California. This item can be shipped worldwide.

Brand: POWER JACK
Model: 1200w
MPN: does not apply
Country/Region of Manufacture: China

Category: 1200w | Comments Off

January 16

1200W, 2500W Grid Tie Inverter 14V-24V, 28V-48V, 52V-88V, 102V-158V MPPT Solar Panel

2015 Version With 3.5 LCD Meter & Solar Panel MPPT Function. 1200 Watt Pure Sine Wave Grid Tie Power Inverter. For 12V(18V VMP) Solar Panel. 95V-130V AC Output 60Hz Frequency. For 24V(36V VMP) Solar Panel. For 48V(72V VMP) Solar Panel. For 96V(144V VMP) Solar Panel. Difference Between Grid Tie Inverter And Grid Tie Inverter With LCD Meter(2015 version). The LCD meter’s watts is 10000w, it can measure your whole appliance, long time to use and hard to damage. Cooling area is larger 30% than old version, tempreture and fan protection hard to run, can save the power of solar panel, so inverter can use best efficieny. It will bring your life covenient, take you to a green world and enjoy freely! Inverter has mppt function, LED light has different display when inverter is low voltage, working voltage, high voltage. User can know the power states of solar panel through LCD meter as watts, voltage, amps and so on, it’s really a smart inverter. AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. 2015 Version With Solar Panel MPPT Function. 2500 Watt Pure Sine Wave Grid Tie Power Inverter. Advantage For Grid Tie. Grid tie inverter is designed for small solar panel energy market, it’s suitable for family enengy system. 14V-24V grid tie inverter suitable for 12v solar panel which rated volt Vmp is about 18V. 28V-48V grid tie inverter suitable for 24v solar panel which rated volt Vmp is about 36V. 52V-88V grid tie inverter suitable for 48v solar panel which rated volt Vmp is about 72V. 102V-158V grid tie inverter suitable for 96v solar panel which rated volt Vmp is about 144V. Do not suitable for wind turbine, pls do not connect wind turbine for the DC source. This inverter can directly use solar panel through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. This inverter only has grid tie inverter function, do not have tranditional inverter function, pls do not connect the battery for 12v dc source, for further questions, pls leave message to ask, tks. The inverter are designed for solar panels energy directly , no need battery! For battery, 24v for dc 14-24v inverter ; 36v for dc 28-48v inverter ;72v for dc 52-88v inverter ; 144v for dc 102-158v inverter ;But please do NOT hook these the inverter to battery banks for a long time , it will burn the inverter up over a period of time. If you want to connect with wind turbine , need connect with a dump load controller 12v for dc 14-24v inverter ; 24v for dc 28-48v inverter ; 36v for dc 52-88v inverter ; 72v for dc 102-158v inverter. This kind micro grid tie inverter, at the beginning its output will go up, but when the inverter inside is hot and temperature is too high, the fan will work, the inverter’s output will reduce or stop work for some seconds, after the inverter become cool, it will auto work again, and its output will go up. Separate the position of Red and Black terminal, would not cause short circuit easy. There are one big ball type fan. Speed is equal to CPU’s 2 times. Life time is CPU’s 5 times. Old version is SMT parts, easy drop. 2015 version is DIP, not easy drop and with long life time. 2015 version have 2 group capacity , total 12 pcs , low impedance. Filter is more effective, heating temperature is lower 15 degree than old version. Old version adopts current and voltage control IC, instability. Microchip from USA, it is very. Reaction speed is 10 times faster, 100 times high precision. Double protect for AC when over voltage, island reaction, and voltage spike. It will protect the inverter quickly when city power instability. Old version: turn off the switch, the vestigial current and voltage in DC side may damage the ac mosfets. 2015 new version: when turn off the switch, it will turn off both Ac and Dc side, cut off IC signal, would not damage the mosfet. When input power have 600w , the efficiency can reach to 90% , fan would not work , high efficiency will lead inside not to fever, can save solar power; when input power reach 1200w , the efficiency will keep on 87.5%. 2015 new version only have 1 bi-color light. Low voltage: red light flash, inverter no work. High voltage: green light always on, inverter no work. Normal work situation: green light flash, higher watt flash faster. For this design you are very clear to know where is the problem if the inverter not work, very easy to know if from your solar panel or inverter. Sometimes, if you are using some heavy appliance like motor, enginee, cause the voltage up down very fast, in this moment, big amp will come into the grid tie inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid tie inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment, the lightining protection can release thousand voltage to protect the inverter not damage. High speed AC fuse. We now provide access to the ac fuse from the outside of the inverter. Each inverter will come our special ac fuse. This will protect the inverter in less than a millisecond to help prevent high voltage. Spikes from feeding back into the circuitry! Grid Tie Power Inverter? When you use solar panel through grid tie inverter, your home power meter will reduce the speed(if you are using other electric appliances), or your home power meter will backward(if you are not use any appliances). The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The inverter IC will monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase will be match the grid’s, and the volume will be higher than the grid’s, then according to our current controlled PWM, to control the output power to the grid. The inverter will puts out power when the home grid is on. Traditional grid tie inverter is the solar panel are connect in series, so if one solar panel did not work or bad efficiency, then the whole system will be effects, but power jack grid tie inverter, you can use every inverter in parallel, in this moment, each inverter has it’s own MPPT, can make every solar panel got the max power. Our grid tie inverter has 3greens light, when the charge fucntion is normal, then this 3lights will turn on, but if there are not dc sources(like in the night, no sun shine or raining day), the red led light will turn on, the inverter will stop to work, in this moment, the inverter will close the door, the home grid power will not back to inverter. When you set up the grid tie inverter. Pls put the AC plug first. After plug into the home ac source. Dont remove the plug anymore. Otherwise it may have hight voltage spikes. Then connect the DC input. When you want remove the grid tie inverter. Please take away the DC input first. Then you can remove the AC plug. Accessary: will including the AC power cord, DC cable will not including! Fast, Reliably and Directly!! Website for ref is. International Buyers Please Note. The item “1200W, 2500W Grid Tie Inverter 14V-24V, 28V-48V, 52V-88V, 102V-158V MPPT Solar Panel” is in sale since Wednesday, March 09, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “powerengineryworld2011″ and is located in USA. This item can be shipped to United States, to Canada, to United Kingdom, DK, RO, SK, BG, CZ, FI, HU, LV, LT, MT, EE, to Australia, GR, PT, CY, SI, to Japan, to China, SE, KR, ID, to Taiwan, ZA, TH, to Belgium, to France, to Hong Kong, to Ireland, to Netherlands, PL, to Spain, to Italy, to Germany, to Austria, RU, IL, to Mexico, to New Zealand, PH, SG, to Switzerland, NO, SA, UA, AE, QA, KW, BH, HR, MY, BR, CL, CO, CR, PA, TT, GT, HN, JM.

Brand: power jack
MPN: power jack

Category: 1200w | Comments Off

February 24

1200W Grid tie power inverter DC 102V-158V to AC 110V + LCD, MPPT for solar

2014 6.0 new. 1200W Grid tie power inverter. DC 102V-158V to AC 110V. With 3.5 LCD meter. For solar panel 96V system (best solar panel working voltage 125V135V). AC Output watt :0 Watt (Max display power 15KWcan display running power less than 1W). AC Output Volt : 0 volt (Max display volt 270V). AC Output Amp : 0 Amp (Max display amp 55A). Total Operation time :0-60000 hoursOperation time: 059 minutes to 24 hours to 2500 days. Electricity consumption: 01000000 kwh. Total operation time , electricity consumption and electricity cost can clear. Can set up power , the meter will alarm when reach reserve power. Can set up the cost. Refresh rate: one time 0.5 seconds. Whats new of 2014 6.0 version? We separated the positions of the Red and Black DC input terminals. This provides for easier connection and makes an accidental short circuit much less likely. There are 2 ball type fans for greater air flow. The CPU lifetime is extended by 5 times the old version’s. PCB board: last version used SMT parts. These are easily dislodged by impacts or thermal expansion. The new version has 2 groups of capacitors, total 12 pieces. The low impedance filter is more efficient, running 27. Cooler than old version. The old version used a current and voltage control IC that had instabilities. The new version uses a new microchip from the USA. It is very stable and the reaction speed is 10 times faster, 100 times more precise. Double protection circuit for AC when there is over voltage, an island reaction, or a voltage spike. This will protect the inverter quickly if there is instability in line power. For the old version, when switch off the inverter, vestigial current and voltage in the DC side could damage the AC mosfets. In the new version, when you turn off it, it will turn off both AC and DC sides and cut off the IC signal. This will prevent any damage to the mosfets. When input power is 600w, the efficiency can reach to 90%, so the fan does not need to run offend. The high efficiency keeps the insides cool and can utilize a greater percentage of your solar power. When input power reach 1200w , the efficiency will stay at or above 87.5%. The new version has only 1 bi-colored light: low voltage: the red light flashes and the inverter will not function. High voltage: the green light always on and the inverter will not function. Normal situation: The led light will be green color flashed; led light will flash fast when power is strong. PSWGT-1200-102-158-110 + LCD meter. DC 102-158 Volt (solar panel). No Load current Draw. 55 C ± 5. Dimensions (L x W x H /cm). 43 22 8 CM. The inverter are designed for solar panels energy directly , no need battery! For battery, 24V battery for DC 14V-24V inverter; 36V for DC 28V-48V inverter, but please do NOT hook inverter with battery banks for a long time , it will burn the parts of inverter over a period of time. Sometimes, if you are using some heaving appliance like motor, engine, cause the voltage up down very fast, in this moment, big amp will come into the grid inverter, easy to cause the ac mos burned, so surge protector will cut down by itself to protect the grid inverter. You may have experience, when meet the big lightning, the power source of the home appliance may damage, same reason, will also cause the inverter damage, in this moment the lightning protection can release thousand voltages to protect the inverter not damage. High speed AC fuses. Now we put ac fuse outside, each inverter will come our special ac fuse, this will be broken 1 mini/sec, to make sure high voltage spike come in! Is designed for small solar panel & wind energy market, it’s suitable for family energy system. This inverter can directly use solar panel, wind charger through inverter to home grid. Easy to installation, just need solar panel, grid tie inverter, then directly can put into home grid. The inverter can be connected to any outlet in the home providing line power. The inverter IC will monitors the voltage, frequency and phase of the home grid, then produce a pure sine wave phase locked to the grid. The voltage will be just enough higher than the grid’s to feed power into the grid, Then using our current controlled PWM we control the output power to the grid. The inverter will put out power when the home grid is on. The inverter will stop feeding power into the grid when the grid is down, for safety and as required by law. Why should you use a grid tie inverter? When you use power from solar panels to supply the inverter, your home power. Meter will run more slowly(if you are using other electric appliances), or your. Home power meter will run backward(if you are not use any appliances). Why should you use a Power Jack grid tie inverter. In traditional grid tie inverters, the solar panels are connect in series so if one solar panel did not work or had poor efficiency or had a blown bypass diode, then the whole system is affected. With Power Jack inverters, you can use all panels in parallel so if one is not working properly, you only lose the output from that one panel. You can also run several Power Jack inverters parallel instead of having one large expensive unit. If you have just one expensive inverter and it fails you produce no power. If you have several smaller units and one fails you still produce power. Each inverter has it’s own MPPT function so you can extract the maximum power from all of your solar panels. When the dc charge function is normal, the inverter supplies power. If there are no dc sources (like at night or a cloudy or rainy day), the inverter will stop attempting to supply power and shut itself off from the power grid to protect itself and lengthen its lifetime. For DC 14V-24V inverter. For DC 28V-48V inverter. For DC 50V-88V inverter. For DC 102V-158V inverter. 11.5V – 13.5V. Orange light on, fan keep working, but inverter stop working. Green flash faster and more powerful output. Manufacture defects or workmanship, use appropriately, surface of item do not scratch. Manufacture defects or workmanship excludes damage caused by inappropriately used such as improper installation, accident, misuse, abuse, improper storage, or any unauthorized disassembly, repair, or modification. My solar panels are 210W 5 pcs, should I use 5 panels on one inverter or 4 panels. I live in the USA and we use 110V or 220V at 60 cycles. Should I use 1200W grid tie power inverter DC 14V-24V to AC 220V with LCD power meter for solar or 1200W grid tie inverter DC 28V-48V to AC 110V with LCD meter for my solar panels? Should I run them in set of two and double the voltage to 57.7? I like to set it up where I can get the most out of the inverters and the panels, your comments will be highly appreciated. You can use our 1200W grid tie power inverter DC 28V-48V TO AC 220V 60HZ due to below reasons. Your solar panels no load voltage are 35V, and 28V after loading, then the above DC range is just fit it. You can use 5 pcs solar panel and connect them in parallel(DC voltage will be 28V). Then connect them with 1 unit 1200W grid tie power inverter. Regarding use AC 220V system inverter, most home main AC power is 220V. In United States, then separate to 110V(sockets on wall), so you can connect the inverter to home main power (220V) directly. It is ok to use AC 110V inverter, just plug into any home AC 110V socket, but might lose 5-10% power. Q: how to connect Power Jack grid tie inverter? A: inverters DC side connect with solar panels, then the inverter’s plug just plug into home AC socket, and turn on inverter to start work. It is easy to use and no need to add controller. Q: Can solar panels can be hook in series or in parallel? A: solar panels can be hook in series or in parallel, if solar panels are in same voltage, they can be hook in series or in parallel. But if solar panels not in same voltage, they only can be hook in series, can not hook in parallel. Q: Can your grid tie power inverter can be hook together? A: yes, our grid tie power inverter can be connect in parallel, but must be same version. The item “1200W Grid tie power inverter DC 102V-158V to AC 110V + LCD, MPPT for solar” is in sale since Tuesday, February 23, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “6apex_2012″ and is located in warehouse. This item can be shipped worldwide.

Brand: POWER JACK
Model: 1200w
MPN: does not apply
Country/Region of Manufacture: China

Category: 1200w | Comments Off

November 2024
M	T	W	T	F	S	S
« Oct
				1	2	3
4	5	6	7	8	9	10
11	12	13	14	15	16	17
18	19	20	21	22	23	24
25	26	27	28	29	30