45-90v

Max Efficiency:>92% MPPT Efficiency:99%. DC/3PHASE AC 22-65V/ 45V-90V. AC 100V 110V 120V 220V 230V 240V 50hz 60hz. NEW 1000W Wind Power Grid Tie Inverter. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire solar power system. Overload protection, Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD. Input AC/DC Voltage Range. AC Output Voltage Range. 90-130V / 190VAC 260VAC. Dimensions (W x H x D). (1) (2) Dump load resistor connection Terminal. This terminals will connect to the dump load resistor. (3) AC socket, This socket will connect the inverter to the public grid via the AC cable. This terminals will connect to the wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet for this wind inverter. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. Advanced patented technology, MPPT efficiency is higher. High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years. Each inverter need to pass twice testing (20 hours) before leaving factory. Combination of SGPV does not interact. Als berechtigter Importeur sind Sie für angemessene Steuern oder Einfuhrgebühren verantwortlich. Alle Artikelstandorte in Berlin, Deutschland DE Lagerbestand DE bis DE 2 Werktage! Wenn Sie Ihren Artikel nach 20 Tagen nicht erhalten, kontaktieren Sie uns bitte umgehend für weitere Hilfe. Wir haften für alle Schäden oder Verluste, die beim Versandprozess entstehen. Einfuhrzölle, Mehrwertsteuer und andere Gebühren sind NICHT im Artikelpreis oder den Versandkosten enthalten. Als berechtigter Importeur sind Sie für angemessene Steuern oder andere Einfuhrgebühren verantwortlich. Wenn Sie mit unseren Produkten und unserem Service zufrieden sind, hinterlassen Sie uns bitte ein positives Feedback und eine 5-Sterne-Bewertung, und wir werden dasselbe für Sie tun. Bitte zögern Sie nicht, uns zu kontaktieren, wenn Sie Fragen haben. Wir werden Ihnen so schnell wie möglich antworten und unser Bestes geben, um Ihre Probleme zu lösen. Glauben Sie uns, jeder Kunde wird als unser wichtiger Schatz angesehen. Und bitte kontaktieren Sie uns Bitte beachten Sie, dass durch die folgenden Anweisungen Ihre Mitarbeit sehr geschätzt wird und die Garantiezeit automatisch verlängert werden kann. Q1: Was kann ich tun, wenn ich meinen Artikel nicht rechtzeitig erhalten habe? A1: Bitte suchen Sie den Bestelldatensatz, wählen Sie “Verkäufer kontaktieren” im Dropdown-Menü auf der rechten Seite, das zu einer neuen Seite führt, und “Wählen Sie ein Thema aus”. Q2: Wie können wir verarbeiten, wenn ich mit Ihrem Produkt nicht zufrieden bin? A2: Bitte klicken Sie unten auf “Diesen Artikel zurückgeben”, suchen Sie die folgenden 3 Optionen und wählen Sie eine aus, um fortzufahren, sollte in Ordnung sein. PS: Die Gründe für die Rücksendung sind nicht wichtig, egal welche Sie auswählen, wir müssen sie weiter bestätigen die Details per Nachricht. Als führendes und aufstrebendes Unternehmen im Hersteller- und Exportgeschäft ist Bayoung seit mehr als 10 Jahren auf Geschäfts- und Industrieprodukte, Haus- und Gartenprodukte spezialisiert. Wir glauben, dass es unsere Vision und Mission ist, innovative Produkte anzubieten mit bestem Service und konkurrenzfähigem Preis, um Sie zufriedenzustellen. Unser Ziel ist es, sicherzustellen, dass Sie genau das finden, wonach Sie suchen, und Ihnen das Aufgeben Ihrer Bestellungen zu erleichtern. Willkommen in unserem Shop! Ihre Zufriedenheit ist unsere höchste Priorität. Bitte zögern Sie nicht, uns zu kontaktieren, wenn Sie Fragen zu unseren Produkten oder Dienstleistungen haben. Unsere Arbeitszeit (Montag bis Freitag): -09:00-12:00 (GMT+8) -14:00-18:00 (GMT+8) Samstag: -09:00-12:00 (GMT+8) -14:00-17:00 (GMT+8). Alle E-Mails werden während unserer Arbeitszeit sehr schnell beantwortet, E-Mails werden normalerweise während des Urlaubs innerhalb von 24 Stunden beantwortet. Willkommen, um uns zu kontaktieren, wenn Sie ein Problem haben. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “qiu7976″ and is located in this country: CN. This item can be shipped worldwide.

Output Voltage: 1000W 90-260V AC
Input Voltage: 22V-66V
Size: 434*196*88mm
Model: GTINVT20
Maximum Input Power: 1801-2000 W
Type: Charger/Inverter
Color: Blue
Recommended Environment: Outdoor
Brand: qiu7976
Application: Agriculture/Farming, Aquaculture, Automotive, Back-up Power, Camping/Hiking, Commercial, Electronics, Home/Garden, Irrigation, Marine
Resistance Properties: Abrasion Resistant, Acid Resistant, Antimicrobial Resistant, Chemical Resistant, Childproof, Child Resistant, Corrosion Resistant, Dustproof, Dust Resistant, Fade Resistant
Current Rating: 11-20 A
Inverter Technology: Hybrid
Wattage: 1500-1999 W
Current Type: AC/DC
System Configuration: Grid-Tie
Power Source: Wind
Features: All Daylight Conditions, Automatic Voltage Detection, Brushless Motor, Corrosion Resistant, Daylight Operation, Fixed Guyed, Flexible, Foldable, Freestanding
Protection Properties: Anti-island Protection, Black Current Protection, Discharge Protection, Freeze Protection, Frost Protection, Lightning Protection, Low Voltage Protection, Open Circuit Protection, Overcharge Protection, Overcurrent Protection
Power: 1000 /2000 W
Current Output: 11-19 A
Charging Mode: MPPT (Maximum Power Point Tracking)
Voltage: 41-50 V

Category: phase | Comments Off

March 17

1KW 2KW MPPT Solar Panel on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V

Home & Farm Appliances. 2KW 1KW Solar on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V PV System. Why we produced the GRID TIE Grid connectINVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Low cost and easy installation – Easy installation of solarmodules and grid tie inverter. It just needs very low maintenance costs. Free combination – SGPV can be used as a separate grid tie system and can be setup as a large solar array withmany of them. The quantity of SGPV in the array is just according to your desire. Combination of SGPV does not interact – The traditional solar grid tie system, they offer units ranging in high power output and these units aremodular so you can havemultiple units operating in parallel for large solar arrays. Improving the efficiency of the entire solar power system In traditional grid tie system, the solar panels are connected in series, so the MPPT of the inverter is according to the total panels in series, not to every panel, but there is difference between every panel, so not every panel is working at the maximum power, this will reduce the total power of these panel in series. Low power consumption Most of the parts in the small grid-tie inverter are digital ICs and low powerMCU, so the power consumption of it is low, though the quantity of grid tie inverter. Output Voltage Automatic Adaptation AC 110V 120V 220V 230V 240V (automaticly). Automatic current detection limit function / Wifi Function 8. The screen can display daily power generation & total power generation , real-time waveform display of the power grid , real-time voltage & current of solar energy system, real-time power , internal temperature , date and time. 600W Grid Tie Power Inverter. DC Input Voltage : 22V50V. Recommend use PV panels. 600W / Vmp>34V / Voc. DC MAX input current. AC MAX output power. DC MAX Open-circuit input-voltage. DC input voltage range. MAX output power factor. DC input Reverse voltage protection. AC output voltage range. 49.3-50.5 Hz. Output short circuit protection. Power line carrier-current communication. 1000W Grid Tie Power Inverter. DC Input Voltage : 22V65V. AC Output Voltage Range. AC Output Frequency Range. 412815.5cm(16.14″11″6.1). DC Input Voltage : 45V90V. 2000W Grid Tie Power Inverter. (DC 45V-90V, AC 220V-250V), USA Plug. 51.5x30x15cm(20.3″x11.8″x5.9). How to use the Inverter? Standard Grid Tie Inverter Model(one unit inverter). More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. 2.1 The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. 2.2 The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. 2.3 The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. 3.1 This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. 3.2 External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. Depend on your own choice 600W DC 22V-50V. 1 x Grid Tie Solar Inverter. 1 x AC Cable. 1 x Limiter sensor clamp & cable. 1 x User manual. Connect the external WIFI device to the GTIL. Power on the GTIL. Your home network will detect the presence of a new Wireless connection. For example, in the picture below, you will see X2116640263692. This is a unique na. This is your wifi device name. It is also the serial number and also the Datalog pi. Write down this characters. It is the same in your cellphone when connecting to. Available wireless connection or WIFI. You will then be prompted to enter security key. Enter 12345678 then press ok. Check if you are connected. Then in the address bar, typ. E 192.168.8.66. Then press enter in your keyboard. Enter username and password. This will be the interface setting between your home router and your GTIL WIFI. See the Network status in red. The item “1KW 2KW MPPT Solar Panel on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V” is in sale since Wednesday, March 10, 2021. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “topsol_6638″ and is located in Rowland Heights, California. This item can be shipped worldwide.

Inverter Technology: Power Optimizer
Wattage: 1000-1499 W
System Configuration: Grid-Tie
Power Source: Solar
Type: Charger/Inverter
Recommended Environment: Indoor
Power: 1001-1200 W
Current Output: 90-99 A
Brand: Eco-worthy
Application: Back-Up Power
Charging Mode: MPPT (Maximum Power Point Tracking)
Voltage: 41-50 V

Category: mppt | Comments Off

January 11

1KW 2KW Solar On Grid Tie Inverter & Power Limiter DC 22-65V/45-90V kit Home

Home & Farm Appliances. You may also like. 1000W 1KW 2KW Solar on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V PV System. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Low cost and easy installation–it can make full use of all types of buildings surface that face to the sun in the city as well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs. Free combination — it can be used as a separate grid tie system and can be setup as a large solar array with many of them. Improving the efficiency of the entire solar power system– Because of MPPT function. So every panel is working at the maximum. 1000W Grid Tie Power Inverter. DC Input Voltage : 22V65V. AC Output Voltage Range. AC Output Frequency Range. 412815.5cm(16.14″11″6.1). DC Input Voltage : 45V90V. 2000W Grid Tie Power Inverter. 51.5x30x15cm(20.3″x11.8″x5.9). How to use the Inverter? Standard Grid Tie Inverter Model(one unit inverter). More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. 2.1 The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. 2.2 The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. 2.3 The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. 3.1 This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. 3.2 External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. Depend on your own choiceeach Inverter have these following accessories. 1 x Solar Grid Inverter with Limiter(built-in). 1 x AC cable. 1 x Internal type Limiter clamp with sensor. 1 x User Manual. Goods in stock in USA, goods will be set by UPS. Or USA customers the most important thing. We strive to serve our customers and resolve any issues. Appreciate the opportunity to correct any issues you have before you leave feedback. Pls visit my store. We do appreciate your consideration and looking forward to doing business with all the clients and companies. We are manufacturers and wholesalers of solar panels and renewable energy products. Our solar business has been established since 2002. OEM and ODM services are both available. We would like to be your best supplier in China. Please take our working time into account. We will reply you in time, if you are in our working time. If you don’t receive our reply within one days, We must be out of work. Please contact me through. Public holidays in China is not available for message reply. The item “1KW 2KW Solar On Grid Tie Inverter & Power Limiter DC 22-65V/45-90V kit Home” is in sale since Tuesday, August 11, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Solar Power Supplies\Solar Power Accessories”. The seller is “renewtopsolar” and is located in Rowland Heights, California. This item can be shipped worldwide.

MPN: ECO-L03
Brand: ECO-WORTHY
MPPT Efficiency: 99%
Peak Inverter Efficiency: 92%
Standby Power Consumption: <0.5w
Dimensions (W x H x D) 2KW: 51.5*30*15
Total Harmonic Distortion: <5%
Output Frequency: 45-65Hz
Internal Limiter: Built-in
Dimensions (W x H x D) 1KW: 41*28*15.5
Output Voltage: 110V or 220V Auto
Input Voltage: 22V-65V or 45V-90V
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Featured Refinements: MPPT

Category: solar | Comments Off

May 19

1000W 2KW Solar Panel on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V kit

Home & Farm Appliances. You may also like. 1000W 1KW 2KW Solar on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V PV System. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Low cost and easy installation–it can make full use of all types of buildings’ surface that face to the sun in the city as well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs. Free combination — it can be used as a separate grid tie system and can be setup as a large solar array with many of them. Improving the efficiency of the entire solar power system– Because of MPPT function. So every panel is working at the maximum. 1000W Grid Tie Power Inverter. DC Input Voltage : 22V65V. AC Output Voltage Range. AC Output Frequency Range. 412815.5cm(16.14″11″6.1). DC Input Voltage : 45V90V. 2000W Grid Tie Power Inverter. 51.5x30x15cm(20.3″x11.8″x5.9). How to use the Inverter? Standard Grid Tie Inverter Model(one unit inverter). More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. 2.1 The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. 2.2 The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. 2.3 The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. 3.1 This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. 3.2 External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. Depend on your own choiceeach Inverter have these following accessories. 1 x Solar Grid Inverter with Limiter(built-in). 1 x AC cable. 1 x Internal type Limiter clamp with sensor. 1 x User Manual. Goods in stock in USA, goods will be set by UPS. Or USA customers the most important thing. We strive to serve our customers and resolve any issues. Appreciate the opportunity to correct any issues you have before you leave feedback. Pls visit my store. We do appreciate your consideration and looking forward to doing business with all the clients and companies. We are manufacturers and wholesalers of solar panels and renewable energy products. Our solar business has been established since 2002. OEM and ODM services are both available. We would like to be your best supplier in China. Please take our working time into account. We will reply you in time, if you are in our working time. If you don’t receive our reply within one days, We must be out of work. Please contact me through. Public holidays in China is not available for message reply. The item “1000W 2KW Solar Panel on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V kit” is in sale since Tuesday, January 14, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “ecoworthy_llc” and is located in Rowland Heights, California. This item can be shipped worldwide.

MPPT Efficiency: 99%
Peak Inverter Efficiency: 92%
Standby Power Consumption: <0.5w
Dimensions (W x H x D) 2KW: 51.5*30*15
Total Harmonic Distortion: <5%
Output Frequency: 45-65Hz
Internal Limiter: Built-in
Dimensions (W x H x D) 1KW: 41*28*15.5
Output Voltage: 110V or 220V Auto
Input Voltage: 22V-65V or 45V-90V
MPN: ECO-L03
Brand: ECO-WORTHY
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Featured Refinements: MPPT

Category: 1000w | Comments Off

April 30

1000W MPPT Solar Grid Tie Inverter Power Limiter DC 22-65V/45-90V to 110-220V US

IMeshbean 1000W MPPT Solar Grid Tie Inverter Pure Sine Wave Power Limiter Auto Switch PV System DC 22V-60V/45-90V to AC 110V 220V Stackable USA. Brand: iMeshbean 100% High Quality. We have proudly designed our own products and successfully created our own brands in the industries. In order to provide the peaceful shopping experience, our dedicated customer service teams can response to all the requests within 24 hours. We honor 30 days return on any products customers are not satisfied. Being our customer is a wise choice! Please note that Option B inverter has no limiter built in. It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Low cost and easy installation. Easy installation of solarmodules and grid tie inverter. It just needs very low maintenance costs. Free combination – It can be used as a separate grid tie system and can be setup as a large solar array withmany of them. Its quantity in the array is just according to your desire. Its Combination does not interact – The traditional solar grid tie system, they offer units ranging in high power output and these units aremodular so you can havemultiple units operating in parallel for large solar arrays. Improving the efficiency of the entire solar power system In traditional grid tie system, the solar panels are connected in series, so the MPPT of the inverter is according to the total panels in series, not to every panel, but there is difference between every panel, so not every panel is working at the maximum power, this will reduce the total power of these panel in series. Low power consumption Most of the parts in the small grid-tie inverter are digital ICs and low powerMCU, so the power consumption of it is low, though the quantity of grid tie inverter. Automatic current detection limit function. Internal limiter are settable. LCD Display The screen can display daily power generation & total power generation, real-time waveform display of the power grid, real-time voltage & current of solar energy system, real-time power, internal temperature , date and time. Option B(No limiter). AC Output Frequency Range. 46 Hz – 65 Hz. Just for AC output. Depend on your own choice(Option B has no internal limieter)each Inverter have these following accessories. 1 x Solar Grid Inverter. 1 x AC cable. 1 x Internal type Limiter clamp with sensor & 6.5FT cable. 1 x User Manual. A:DC input , for solar panels connectionpositive. B: DC input , for solar panels connectionnegative. C: Connector for external limiter(Not included). D: Connector for internal limiter (have been Integrated in the inverter, no need to connect). E: AC output , use AC cable to connect to home grid. Standard Grid Tie Inverter Model(one unit inverter). More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. 2.1 The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. 2.2 The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. 2.3 The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. 3.1 This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. 3.2 External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. We are not responsible for undeliverable address. Pleas message us if recipient address changes needed before we fulfill the order. Sorry, no local pickups available. No need return the original one for low-valued items. All return products should be in original package with all accessories included. We stand behind our products so you are always covered! The item “1000W MPPT Solar Grid Tie Inverter Power Limiter DC 22-65V/45-90V to 110-220V US” is in sale since Friday, October 5, 2018. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “chargerangel” and is located in Pasadena, Texas. This item can be shipped to United States.

Inverter Technology: Microinverter
Style: Modern
Wattage: 1000W
System Configuration: Grid-Tie
Power Source: Solar
Features: Limiter Sensor/ClampOptional
Color: Blue
Voltage Input: DC 22-60V/45-90V
MPN: Does Not Apply
Recommended Environment: Indoor
Protection Properties: Anti-Island Protection
Voltage Output: AC 110V/220V
Brand: Unbranded

Category: 1000w | Comments Off

October 19

1000W 2KW Solar Panel on Grid Tie Inverter&Power Limiter DC 22-65V/45-90V PV Kit

Home & Farm Appliances. You may also like. 1000W 1KW Solar on Grid Tie Inverter & Power Limiter DC 22-65V/45-90V PV System. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Low cost and easy installation–it can make full use of all types of buildings’ surface that face to the sun in the city as well as fast and easy installation of solar modules and grid tie inverter. It just needs very low maintenance costs. Free combination — it can be used as a separate grid tie system and can be setup as a large solar array with many of them. Improving the efficiency of the entire solar power system– Because of MPPT function. So every panel is working at the maximum. 1000W Grid Tie Power Inverter. DC Input Voltage : 22V65V. AC Output Voltage Range. AC Output Frequency Range. 412815.5cm(16.14″11″6.1). DC Input Voltage : 45V90V. 2000W Grid Tie Power Inverter. 51.5x30x15cm(20.3″x11.8″x5.9). How to use the Inverter? Standard Grid Tie Inverter Model(one unit inverter). More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. 2.1 The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. 2.2 The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. 2.3 The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. 3.1 This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. 3.2 External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. 1 x Solar Grid Inverter with Limiter(built-in). 1 x AC cable. 1 x Internal type Limiter clamp with sensor. 1 x User Manual. Goods in stock in USA, goods will be set by UPS. Or USA customers the most important thing. We strive to serve our customers and resolve any issues. Appreciate the opportunity to correct any issues you have before you leave feedback. Pls visit my store. We do appreciate your consideration and looking forward to doing business with all the clients and companies. We are manufacturers and wholesalers of solar panels and renewable energy products. Our solar business has been established since 2002. OEM and ODM services are both available. We would like to be your best supplier in China. Please take our working time into account. We will reply you in time, if you are in our working time. If you don’t receive our reply within one days, We must be out of work. Please contact me through. Public holidays in China is not available for message reply. The item “1000W 2KW Solar Panel on Grid Tie Inverter&Power Limiter DC 22-65V/45-90V PV Kit” is in sale since Sunday, June 23, 2019. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “17winsunpower” and is located in Rowland Heights, California. This item can be shipped worldwide.

Brand: ECO-WORTHY
MPN: ECO-L03
MPPT Efficiency: 99%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Dimensions (W x H x D) 1KW: 41*28*15.5
Dimensions (W x H x D) 2KW: 51.5*30*15
Internal Limiter: Built-in
Featured Refinements: MPPT
Input Voltage: 22V-65V or 45V-90V
Output Voltage: 110V or 220V Auto
Output Frequency: 45-65Hz
Standby Power Consumption: <0.5w
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%

Category: 1000w | Comments Off

April 25

1000W On Grid Tie Inverter With Limiter For Solar Panels 22-65V/45-90V DC System

1000W On Grid Tie Inverter With Limiter For Solar Panels 22-65V/45-90V DC System. The item “1000W On Grid Tie Inverter With Limiter For Solar Panels 22-65V/45-90V DC System” is in sale since Thursday, April 11, 2019. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “ianclaudio563″ and is located in Silver Spring, Maryland. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Turks and caicos islands, Barbados, Bermuda, Bolivia, Ecuador, Guadeloupe, Jordan, Cayman islands, Sri lanka, Martinique, Nicaragua, Oman, Peru, Pakistan, Viet nam, Uruguay, Dominican republic, El salvador.

Power Factor: 0.99
Brand: SUN
Output Wave Form: Pure Sine Wave
Featured Refinements: MPPT
MPPT Efficiency: 99%
Country/Region of Manufacture: China
Peak Inverter Efficiency: 92%
Standby Power Consumption: <0.5w
Bundle Listing: No
Total Harmonic Distortion: <5%
Output Frequency: 45-65Hz
Dimensions (W x H x D): 322x196x88 mm
Weight: 5.5kg
Output Voltage: 100V 110V 120V 220V 230V 240V auto
Input Voltage: 22v-60v or 45v-90v Optional
MPN: SUN-1000G2-LCD

Category: 1000w | Comments Off

December 4

1000W On Grid Tie Inverter with Limiter for Solar DC 22-65V/45-90V AC110/220V

You may also like. 1000W On Grid Tie Inverter with Limiter for Solar DC 22-65V/45-90V AC110/220V. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Gereantion 1000w Standard Solar Power Grid Tie Inverter. DC 22V-65V or 45V-90V (Optional). AC 110V 120V 220V 230V 240V (auto selected). With Battery Discharge Function / Voltage Adjustable. Wi-Fi port (optional). Power Limiter function built-in. SGPV and Grid Tie Inverter. SGPV – small solar grid tie inverter and solar panels. The inverter can obtain the solar energy from solar panel, and tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. When the sun shines, the solar panels will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. The electric apparatus in the house will use power from the inverter first. The power meter will SLOW down. Advantage of the 2G grid tie inverter? The 2nd Generation grid tie inverter, new technical , Higher efficiency. Higher MPPT efficiency , Max 99%. Multiple intelligent protection to ensure safe use. Wide DC input voltage , suitable for all types solar panels. Easy to install and easy to operate. UL1741, IEEE1547, VDE4105 standards. Power Limiter function , Battery discharge function support. Pure sine wave form output , THD < 5%. Input DC Voltage Range. Peak power tracking voltage. AC Output Voltage Range. Dimensions (W x H x D). How to choose the inverter. The 22-65V model inverter will start up at 25V, after starting, the inverter can work in 22V-65V. Vmp 30v-60v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). The 45-90V model inverter will start up at 49.5V, after starting, the inverter can work in 45V-90V. Vmp 50v-90v Solar panels in parallel suggested ; for Vmp 25V-45v solar panels , we suggest 2 panels in series , the total voltage will be 50V-90V , then connect 2 or more groups in parallel. For example : 2 pcs 200-260w (Vmp 31v) connected in series , 2 groups in parallel. About the limiter function. The Limiter function has been built-in. But, there is not limiter sensor/clamp with this product. The function is turned off. If customer want to use limiter function , please order limiter sensor/clamp in the future , or order a limiter model inverter. How to use the grid tie inverter? 1 unit inverter installation / more units inverters in parallel. The inverter AC output can be connected in the AC plug of grid in the house. LCD display and operation. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Note : Limiter model must use limiter sensor/clamp , there is not limiter sensor and clamp with this model inverter. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then powe will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Optional Function : Wi-Fi port. We will message you if it happens. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. The item "1000W On Grid Tie Inverter with Limiter for Solar DC 22-65V/45-90V AC110/220V" is in sale since Tuesday, September 4, 2018. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters". The seller is "homegarden0722" and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: SUN
MPN: SUN-1000G2-LCD
Country/Region of Manufacture: China
Input Voltage: 22v-60v or 45v-90v Optional
Output Voltage: 100V 110V 120V 220V 230V 240V auto
Output Frequency: 45-65Hz
Standby Power Consumption: <0.5w
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
MPPT Efficiency: 99%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Weight: 6kg
Dimensions (W x H x D): 322x196x88 mm
Featured Refinements: MPPT
Bundle Listing: No

Category: 1000w | Comments Off

August 1

1000W On Grid Tie Inverter With Limiter For Solar Panels 22-65V/45-90V DC System

You may also like. 1000W On Grid Tie Inverter With Limiter For Solar Panels 22-65V/45-90V DC System. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Gereantion 1000w Standard Solar Power Grid Tie Inverter. DC 22V-65V or 45V-90V (Optional). AC 110V 120V 220V 230V 240V (auto selected). With Battery Discharge Function / Voltage Adjustable. Wi-Fi port (optional). Power Limiter function built-in. SGPV and Grid Tie Inverter. SGPV – small solar grid tie inverter and solar panels. The inverter can obtain the solar energy from solar panel, and tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. When the sun shines, the solar panels will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. The electric apparatus in the house will use power from the inverter first. The power meter will SLOW down. Advantage of the 2G grid tie inverter? The 2nd Generation grid tie inverter, new technical , Higher efficiency. Higher MPPT efficiency , Max 99%. Multiple intelligent protection to ensure safe use. Wide DC input voltage , suitable for all types solar panels. Easy to install and easy to operate. UL1741, IEEE1547, VDE4105 standards. Power Limiter function , Battery discharge function support. Pure sine wave form output , THD < 5%. Input DC Voltage Range. Peak power tracking voltage. AC Output Voltage Range. Dimensions (W x H x D). How to choose the inverter. The 22-65V model inverter will start up at 25V, after starting, the inverter can work in 22V-65V. Vmp 30v-60v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). The 45-90V model inverter will start up at 49.5V, after starting, the inverter can work in 45V-90V. Vmp 50v-90v Solar panels in parallel suggested ; for Vmp 25V-45v solar panels , we suggest 2 panels in series , the total voltage will be 50V-90V , then connect 2 or more groups in parallel. For example : 2 pcs 200-260w (Vmp 31v) connected in series , 2 groups in parallel. About the limiter function. The Limiter function has been built-in. But, there is not limiter sensor/clamp with this product. The function is turned off. If customer want to use limiter function , please order limiter sensor/clamp in the future , or order a limiter model inverter. How to use the grid tie inverter? 1 unit inverter installation / more units inverters in parallel. The inverter AC output can be connected in the AC plug of grid in the house. LCD display and operation. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Note : Limiter model must use limiter sensor/clamp , there is not limiter sensor and clamp with this model inverter. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then powe will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Optional Function : Wi-Fi port. We will message you if it happens. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. The item "1000W On Grid Tie Inverter With Limiter For Solar Panels 22-65V/45-90V DC System" is in sale since Friday, April 27, 2018. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters". The seller is "yoosmart2009" and is located in Los Angeles. This item can be shipped to North, South, or Latin America.

Brand: SUN
MPN: SUN-1000G2-LCD
Country/Region of Manufacture: China
Input Voltage: 22v-60v or 45v-90v Optional
Output Voltage: 100V 110V 120V 220V 230V 240V auto
Output Frequency: 45-65Hz
Standby Power Consumption: <0.5w
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
MPPT Efficiency: 99%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Weight: 5.5kg
Dimensions (W x H x D): 322x196x88 mm
Featured Refinements: MPPT
Bundle Listing: No

Category: 1000w | Comments Off

July 28

1000W On Grid Tie Inverter with Limiter for Solar DC 22-65V/45-90V AC110/220V

You may also like. 1000W On Grid Tie Inverter with Limiter for Solar Panels/Battery Power PV System. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Gereantion 1000w Standard Solar Power Grid Tie Inverter. DC 22V-65V or 45V-90V (Optional). AC 110V 120V 220V 230V 240V (auto selected). With Battery Discharge Function / Voltage Adjustable. Wi-Fi port (optional). Power Limiter function built-in. SGPV and Grid Tie Inverter. SGPV – small solar grid tie inverter and solar panels. The inverter can obtain the solar energy from solar panel, and tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. When the sun shines, the solar panels will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. The electric apparatus in the house will use power from the inverter first. The power meter will SLOW down. Advantage of the 2G grid tie inverter? The 2nd Generation grid tie inverter, new technical , Higher efficiency. Higher MPPT efficiency , Max 99%. Multiple intelligent protection to ensure safe use. Wide DC input voltage , suitable for all types solar panels. Easy to install and easy to operate. UL1741, IEEE1547, VDE4105 standards. Power Limiter function , Battery discharge function support. Pure sine wave form output , THD < 5%. Input DC Voltage Range. Peak power tracking voltage. AC Output Voltage Range. Dimensions (W x H x D). How to choose the inverter. The 22-65V model inverter will start up at 25V, after starting, the inverter can work in 22V-65V. Vmp 30v-60v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). The 45-90V model inverter will start up at 49.5V, after starting, the inverter can work in 45V-90V. Vmp 50v-90v Solar panels in parallel suggested ; for Vmp 25V-45v solar panels , we suggest 2 panels in series , the total voltage will be 50V-90V , then connect 2 or more groups in parallel. For example : 2 pcs 200-260w (Vmp 31v) connected in series , 2 groups in parallel. About the limiter function. The Limiter function has been built-in. But, there is not limiter sensor/clamp with this product. The function is turned off. If customer want to use limiter function , please order limiter sensor/clamp in the future , or order a limiter model inverter. How to use the grid tie inverter? 1 unit inverter installation / more units inverters in parallel. The inverter AC output can be connected in the AC plug of grid in the house. LCD display and operation. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Note : Limiter model must use limiter sensor/clamp , there is not limiter sensor and clamp with this model inverter. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then powe will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Optional Function : Wi-Fi port. We will message you if it happens. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. The item "1000W On Grid Tie Inverter with Limiter for Solar DC 22-65V/45-90V AC110/220V" is in sale since Sunday, January 14, 2018. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters". The seller is "homegarden0722" and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: SUN
MPN: SUN-1000G2-LCD
Country/Region of Manufacture: China
Input Voltage: 22v-60v or 45v-90v Optional
Output Voltage: 100V 110V 120V 220V 230V 240V auto
Output Frequency: 45-65Hz
Standby Power Consumption: <0.5w
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
MPPT Efficiency: 99%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Weight: 3.6kg
Dimensions (W x H x D): 322x196x88 mm
Featured Refinements: MPPT
Bundle Listing: No

Category: 1000w | Comments Off

November 2024
M	T	W	T	F	S	S
« Oct
				1	2	3
4	5	6	7	8	9	10
11	12	13	14	15	16	17
18	19	20	21	22	23	24
25	26	27	28	29	30