Pure Sine Wave Inverter Optional On Grid Tie Micro MPPT 22-50V WVC600W-120V 230V

1 Wireless communication 433/462MHz. 2 6-grade power search. 3 Wide voltage input(22-50VDC)—1. DC voltage input:2250VDC; 2. Second level power variable voltage conversion. 4 High-frequency two-way and one-way grid function—1. High frequency direct modulation, AC half wave synthesis. 5 Kinds of frequency output function—1. It can apply to 50Hz and 60Hz frequency of AC; 2. Frequency range: 45Hz 64Hz. 6 Directly connected to the solar panels(do not need to connect the battery). 7 AC 0 angle with high precision auto-detection—AC switching: 50Hz / 60Hz. 8 Synchronous High-frequency Modulation. Synthetic way: MOSFET full-bridge; 3. 9 Pure Sine Wave Output—Use SPWM directly to make pure sine wave output. 10 Power Automatically Locked (APL)—automatically powers locked in maximum power point, made output more stable. 11 Constant Current, Constant Power—constant current and output power, without any overload, over-current phenomenon. 12 Exactly and timely automatic Island Effect Protection. 13 High-Frequency High Conversion Rate—Adapt high frequency converter, the output more efficient. 14 Maximum Power Point Tracking (MPPT)—high-precision (MPPT) operation power. 15 Stack using—Such as: 4 micro inverter of 260W stacking can achieve 1040W. The number of the stacking is unlimited. 16 DC input—Input voltage range: 22V to 50V, PV Panel. 17 AC output—220VAC: 180V – 262V, 50HZ; 110V AC: 80V – 160V, 60HZ. Dear customer, if you have any problems or need more information about this item, please send us a message and we will give to You more information or will give the best solutions to solve it. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “mutango” and is located in this country: CN. This item can be shipped worldwide.

Input Voltage: 36V
Output Voltage: 230V
Size: 283mm*200mm*41.6mm
Model: 001
Country/Region of Manufacture: China
Output Voltage Range: 80-160VAC,180-260VAC option
Peak power tracking voltage: 22-45V
Recommended input power: 600Watt
Recommended using solar panels: Power 2pcs 350W,36-50VOC
Waterproof Rating: IP65
Weight: 3.5kg
Certification: CE
Cooling: Self-cooling
Is_customized: Yes
Max DC short-circuit: 40A
Current Type: AC/DC
System Configuration: Grid-Tie
Maximum Input Operating Current: 27.2A
Type: Charger/Inverter
Features: Automatic Voltage Detection
Power: Less Than 100 W
Current Output: 10 A or Less
Brand: Unbranded
Application: Agriculture/Farming
Charging Mode: MPPT (Maximum Power Point Tracking)
Min / Max start voltage: 22-50V
Origin: Mainland China
Output Current: 9.58A-120V, 5A-230V
Output Frequency: 47-52.5Hz/57-62.5Hz
Output Power: 500 – 1000W
Output Type: Single
Resistance Properties: Heat Resistant
Voltage: 10 V or Less

Category: pure | Comments Off

June 8

Wind Grid Tie Inverter Dump Load Resistor MPPT Wifi Function Optional AC Turbine

Wind Grid Tie Inverter Dump Load Resistor MPPT Wifi Function Optional AC Turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter modeplease choose the mode. , inverter need a external limiter module working with it. Limit Mode:External limiter and Internal limiter are settable. Limit mode+External limiter both selected means work under external limiter mode. Limit mode+Internal limiter both selected means work under external limiter mode. LCD back light:Select it, Lcd will always on. Unselect it, Lcd will auto turn off after about 10s without any action on lcd button. Press any of the button to light lcd again. Remote Num:while using with wifi plug for monitoring, set by 1. While using with the WIFI-RTU(one rtu can monitoring multiple inverters), set monitored inverter numbers. Bat or solar limited current mode:This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. Mppt function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Battery and solar limited power mode:At this working mode, cut off voltage setting is same as 6.4, and the power setting is the maximum output power of the. The 22-65V type inverter will start up at 25V, and 45-90V type inverter will start up at 49.5V, after start, inverter can still work until 22v or 45v. Current sensor Orientation:Please check the current flow direction arrow on the sensor before use, make sure the connection is correct. Otherwise, inverter will not start up at limit mode. Negative power under AC voltage means power overflow to the grid. Positive means power come from the grid. Wifi Port for MPPT 1000W/2000W NEW SUN Grid Tie Inverter. NOTE : this WIFI port must be ordered with 2nd Generation Grid Tie Inverters together. NOTE : It will be built-in side the inverter. There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “audosta” and is located in this country: CN. This item can be shipped worldwide.

Color: No WIFI
Input Voltage: 3phase AC22-65V
Output Voltage: AC 185-265V
Socket Type: No Limiter
Size: 322x196x88mm
Current Rating: Other
Inverter Technology: Microinverter
Model: 5175583956
Country/Region of Manufacture: China
Output Type: Single
Custom Bundle: No
Output Waveform: Pure Sine Wave
Phase: Single Phase
Warranty: 1Year
Weight: 5KG
Current Type: AC
System Configuration: Grid-Tie
Power Source: Wind
Type: DC/AC Inverters
Features: Zero export
MPN: 5175583981
Recommended Environment: Indoor/Outdoor
Item Length: Standard
Power: 1000W
Current Output: Other
Brand: Unbranded
Application: Agriculture/Farming, Camping/Hiking, Home/Garden
Charging Mode: MPPT (Maximum Power Point Tracking)
AC Output Voltage: 90-260VAC
DC Input Voltage: 22-65V/45-90V
Efficiency: 92%
Is_customized: Yes
Max.Output Power: 1000W
Output Frequency: 50hz/60hz
Output Power: 1000W
Resistance Properties: Other
Voltage: Other

Category: wind | Comments Off

December 21

1000W LCD Grid Tie Inverter battery discharge Inverteral limiter/WIFI optional

1000GTIL2-LCD—-share the same program, but no clamp sensor would be sent if you choose model 1000G2-LCD. Latest updated program enable customers using battery discharge power mode. This is the 2. The first generation GTIL must be used with an additional limiter module, we also add an switch button to enable. The inverter either can work at limit mode or at normal grid tie mode. Generation GTIL, we integrated the limit function inside the GTI. Customer install inverter far away from the main circuit breaker, we also enable the 2. GTIL work with stand-alone limiter, we call this-external. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. Max input DC voltage. Peak power tracking voltage. 47.5-51.5 for 50hz; 59.3-60.5 for 60hz. Just for AC output. 20’C — +85’C. Settings Explainations on the LCD of the 2. The GTIL including various functions, all functions should configurate on the LCD setting page. Please see below explainations. Limit Mode:External limiter and Internal limiter are settable. Limit mode+External limiter both selected means work under external limiter mode. Limit mode+Internal limiter both selected means work under external limiter mode. LCD back light:Select it, Lcd will always on. Unselect it, Lcd will auto turn off after about 10s without any action on lcd button. Press any of the button to light lcd again. Remote Num:while using with wifi plug for monitoring, set by 1. While using with the WIFI-RTU(one rtu can monitoring multiple inverters), set monitored inverter numbers. Bat or solar limited current mode:This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. Mppt function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. The 22-65V type inverter will start up at 25V, and 45-90V type inverter will start up at 49.5V, after start, inverter can still work until 22v or 45v. Current sensor Orientation:Please check the current flow direction arrow on the sensor before use, make sure the connection is correct. Otherwise, inverter will not start up at limit mode. Negative power under AC voltage means power overflow to the grid. Positive means power come from the grid. Clamp Sensor with 2m cable—1pcs;(only available for 1000GTIL2-LCD). The item “1000W LCD Grid Tie Inverter battery discharge Inverteral limiter/WIFI optional” is in sale since Tuesday, June 12, 2018. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “sunhome910″ and is located in shanghai. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Country/Region of Manufacture: China
MPN: Does Not Apply
Brand: Tricorpower
Type: Grid Tie Inverter

Category: 1000w | Comments Off

October 14

2000W On Grid Tie Inverter with Limiter Solar Panels Battery Wi-Fi Port optional

You may also like. 2000W On Grid Tie Inverter with Limiter Solar Panels Battery Wi-Fi Port optional. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Gereantion 2000w Standard Solar Power Grid Tie Inverter. With Limiter / Sensor , Battery Discharge Power Mode. AC 220V 230V 240V (auto selected). For USA 240VAC connection , please see photo below. SGPV and Grid Tie Inverter. SGPV – small solar grid tie inverter and solar panels. The inverter can obtain the solar energy from solar panel, and tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. When the sun shines, the solar panels will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. The electric apparatus in the house will use power from the inverter first. The power meter will SLOW down. Advantage of the 2G grid tie inverter? The 2nd Generation grid tie inverter, new technical , Higher efficiency. Higher MPPT efficiency , Max 99%. Multiple intelligent protection to ensure safe use. Wide DC input voltage , suitable for all types solar panels. Easy to install and easy to operate. UL1741, IEEE1547, VDE4105 standards. Power Limiter function , Battery discharge function support. Pure sine wave form output , THD < 5%. Input DC Voltage Range. Peak power tracking voltage. AC Output Voltage Range. Dimensions (W x H x D). How to use the grid tie inverter? 1 unit inverter installation / more units inverters in parallel. The inverter AC output can be connected in the AC plug of grid in the house. LCD display and operation. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Note : Limiter model must use limiter sensor/clamp , there is not limiter sensor and clamp with this model inverter. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then powe will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Optional Function : Wi-Fi port. We will message you if it happens. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. The item "2000W On Grid Tie Inverter with Limiter Solar Panels Battery Wi-Fi Port optional" is in sale since Wednesday, September 5, 2018. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters". The seller is "homegarden0722" and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: SUN
MPN: SUN-2000G2TIL-B
Country/Region of Manufacture: China
Input Voltage: 45v-90v
Output Voltage: AC 220V 230V 240V auto
Output Frequency: 45-65Hz
Standby Power Consumption: <0.5w
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
MPPT Efficiency: 99%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Limiter Sensor Cable: 3m
Weight: 5.5kg
Dimensions (W x H x D): 434x196x88 mm
Internal Limiter: Built-in
Featured Refinements: MPPT
Model: SUN-2000G2TIL-B

Category: 2000w | Comments Off

July 5

2000W LCD Solar Grid Tie Inverter, MPPT pure sine wave built-in limiter optional

New developed grid tie inverter(second generation) with different design structure, enable better and stable operation quality. With much better output pure sine waveform and better PF Value. The inverter is integrated with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. Max input DC voltage. Peak power tracking voltage. 47.5-51.5 for 50hz; 59.3-60.5 for 60hz. Just for AC output. 20’C — +85’C. Settings Explainations on the LCD of the 2. The GTIL including various functions, all functions should configurate on the LCD setting page. Please see below explaination. Limit Mode:External limiter and Internal limiter are settable. Limit mode+External limiter both selected means work under external limiter mode. Limit mode+Internal limiter both selected means work under external limiter mode. LCD back light:Select it, Lcd will always on. Unselect it, Lcd will auto turn off after about 10s without any action on lcd button. Press any of the button to light lcd again. Remote Num:while using with wifi plug for monitoring, set by 1. While using with the WIFI-RTU(one rtu can monitoring multiple inverters), set monitored inverter numbers. Bat or solar limited current mode:This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. Mppt function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. The 22-65V type inverter will start up at 25V, and 45-90V type inverter will start up at 49.5V, after start, inverter can still work until 22v or 45v. Current sensor Orientation:Please check the current flow direction arrow on the sensor before use, make sure the connection is correct. Otherwise, inverter will not start up at limit mode. Negative power under AC voltage means power overflow to the grid. Positive means power come from the grid. Clamp Sensor with 2m cable—1pcs;(only available for 2000GTIL2-LCD). Wifi Port for MPPT 1000W/2000W NEW SUN Solar/Wind Grid Tie Inverter Extra cost of 75usd required if. NOTE : this WIFI port must be ordered with 2nd Generation Grid Tie Inverters together. NOTE : It will be built-in side the inverter. Russian buyers were required to fill in the full name; Brazilian buyers are required to leave CPF/CPNJ Number; Chilean buyers are required to leave RUT number. All return products should be in original package with all accessories included. We stand behind our products so you are always covered! The item “2000W LCD Solar Grid Tie Inverter, MPPT pure sine wave built-in limiter optional” is in sale since Thursday, May 10, 2018. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “sunhome910″ and is located in Shanghai. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: Ecopower
MPN: Does Not Apply
Country/Region of Manufacture: China

Category: 2000w | Comments Off

July 4

2000W Wind Turbine on Grid Tie Inverter Wi-Fi port Optional 45-90v 220V 3 phase

You may also like. 2000W Wind Turbine on Grid Tie Inverter Home Power Sun 2000G2 WAL 45-90v 3 phase. NEW 2000W Wind Power Grid Tie Inverter- for 3 Phase Wind Turbines. -with dump load controller and resistor. -Max Efficiency:>92% MPPT Efficiency:99%. -AC 220V 230V 240V 50hz/60hz. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire solar power system. Overload protection , Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD<5%, PF>99%. Build in dump load function. Introduction of Sunshine Grid Tie Inverter for Wind Turbine. The small wind grid tie power inverter can obtain the wind energy from wind turbine, and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. The inverter can be connected to any outlets of utility grid at house. It monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to control the output. Power to the grid. The grid tie inverter only outputs power when the home grid is on. When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these. Power from the inverter will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. Input AC/DC Voltage Range. AC Output Voltage Range. Dimensions (W x H x D). (1) (2) Dump load resistor connection Terminal. These terminals will connect to the dump load resistor. (3) AC socket, This socket will connect the inverter to the public grid via the AC cable. These terminals will connect to the wind turbine. How to select a wind grid tie inverter? Max output power of the wind turbine. 500w-1000w wind turbines , suggest 1000w inverter. 1000w-2000w wind turbines , suggest 2000w turbine. 24v 36v 48v wind turbines , suggest 22-65v inverter. 48v 60v 72v 90V wind turbines , suggest 45-90v inverter. Some wind turbines has been built-in a regulator , the output is DC , please choose DC input type wind inverter. How to use a grid tie inverter with battery and wind turbine? If the user want to use a wind turbine to charge battery first , and output excess power to the grid , we suggest the battery function grid tie inverter(solar power GTI , battery function). The wind inverter can not work with battery well. What is the dump load controller/resistor? The dump load controller/resistor is used to protect the wind turbine and inverter. If the wind speed is too fast , the voltage will be high , it will work to reduce the wind turbines runing speed and voltage. WAL model of grid tie invereter connected with AC output type of wind turbine. Connecting two 1000G2-WAL with a max. Power is the 2KW wind turbine. User manual of the wind power inverter. Wifi Port for MPPT 1000W/2000W NEW SUN Solar Grid Tie Inverter. NOTE : this WIFI port must be ordered with 2nd Generation Grid Tie Inverters together. NOTE : It will be built-in side the inverter. We will message you if it happens. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. The item “2000W Wind Turbine on Grid Tie Inverter Wi-Fi port Optional 45-90v 220V 3 phase” is in sale since Monday, January 15, 2018. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “yoosmart2009″ and is located in Shenzhen. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Brazil, Australia.

Brand: SUN
MPN: SUN-2000G2WAL
Country/Region of Manufacture: China
Power Type: 3 Phase Wind Turbine/Generator
Dump Load Controller: Built-in
Dump load resistor: Included
Display: LCD
Max. Power Output: 2000w
Input AC/DC Voltage Range: 45-90v
AC Output Voltage Range: 185-265VAC auto
Output Frequency: 46Hz~65Hz
Standby Power Consumption: <0.5W
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
MPPT Efficiency: 99%
Over Current Protection: Yes
Over Temperature Protection: Yes
Reverse Polarity Protection: Yes
Anti-Island Protection: Yes
Stackable: Yes
Weight ( Kg): 6.5kg
Dimensions (W x H x D): 434x196x88mm

Category: 2000w | Comments Off

June 15

1000W On Grid Tie Inverter with Limiter for Solar Wi-Fi Function optional

You may also like. 1000W On Grid Tie Inverter with Limiter for Solar Panels/Battery Power PV System. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Gereantion 1000w Standard Solar Power Grid Tie Inverter. DC 22V-65V or 45V-90V (Optional). AC 110V 120V 220V 230V 240V (auto selected). With Battery Discharge Function / Voltage Adjustable. Wi-Fi port (optional). Power Limiter function built-in. SGPV and Grid Tie Inverter. SGPV – small solar grid tie inverter and solar panels. The inverter can obtain the solar energy from solar panel, and tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. When the sun shines, the solar panels will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. The electric apparatus in the house will use power from the inverter first. The power meter will SLOW down. Advantage of the 2G grid tie inverter? The 2nd Generation grid tie inverter, new technical , Higher efficiency. Higher MPPT efficiency , Max 99%. Multiple intelligent protection to ensure safe use. Wide DC input voltage , suitable for all types solar panels. Easy to install and easy to operate. UL1741, IEEE1547, VDE4105 standards. Power Limiter function , Battery discharge function support. Pure sine wave form output , THD < 5%. Input DC Voltage Range. Peak power tracking voltage. AC Output Voltage Range. Dimensions (W x H x D). How to choose the inverter. The 22-65V model inverter will start up at 25V, after starting, the inverter can work in 22V-65V. Vmp 30v-60v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). The 45-90V model inverter will start up at 49.5V, after starting, the inverter can work in 45V-90V. Vmp 50v-90v Solar panels in parallel suggested ; for Vmp 25V-45v solar panels , we suggest 2 panels in series , the total voltage will be 50V-90V , then connect 2 or more groups in parallel. For example : 2 pcs 200-260w (Vmp 31v) connected in series , 2 groups in parallel. About the limiter function. The Limiter function has been built-in. But, there is not limiter sensor/clamp with this product. The function is turned off. If customer want to use limiter function , please order limiter sensor/clamp in the future , or order a limiter model inverter. How to use the grid tie inverter? 1 unit inverter installation / more units inverters in parallel. The inverter AC output can be connected in the AC plug of grid in the house. LCD display and operation. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Note : Limiter model must use limiter sensor/clamp , there is not limiter sensor and clamp with this model inverter. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then powe will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Optional Function : Wi-Fi port. We will message you if it happens. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. The item "1000W On Grid Tie Inverter with Limiter for Solar Wi-Fi Function optional" is in sale since Monday, January 15, 2018. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters". The seller is "yoosmart2009" and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: SUN
MPN: SUN-1000G2-LCD
Country/Region of Manufacture: China
Input Voltage: 22v-60v or 45v-90v Optional
Output Voltage: 100V 110V 120V 220V 230V 240V auto
Output Frequency: 45-65Hz
Standby Power Consumption: <0.5w
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
MPPT Efficiency: 99%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
Weight: 3.6kg
Dimensions (W x H x D): 322x196x88 mm
Featured Refinements: MPPT
Bundle Listing: No

Category: 1000w | Comments Off

February 15

2000W LCD Solar Grid Tie Inverter, MPPT pure sine wave built-in limiter optional

2000W LCD Solar Grid Tie inverter With built-in power limiter, MPPT pure sine wave on grid inverter with latest program DC45-90V to AC 230V, latest program Version 5.1. New developed grid tie inverter(second generation) with different design structure, enable better and stable operation quality. With much better output pure sine waveform and better PF Value. The inverter is integrated with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. If you are about to use multiple units of this inverter, then external limiter has to be used. For more details about the limiter function, pls contact supplier. Max input DC voltage. Peak power tracking voltage. 47.5-51.5 for 50hz; 59.3-60.5 for 60hz. Just for AC output. 20’C — +85’C. Settings Explainations on the LCD of the 2. The GTIL including various functions, all functions should configurate on the LCD setting page. Please see below explaination. Limit Mode:External limiter and Internal limiter are settable. Limit mode+External limiter both selected means work under external limiter mode. Limit mode+Internal limiter both selected means work under external limiter mode. LCD back light:Select it, Lcd will always on. Unselect it, Lcd will auto turn off after about 10s without any action on lcd button. Press any of the button to light lcd again. Remote Num:while using with wifi plug for monitoring, set by 1. While using with the WIFI-RTU(one rtu can monitoring multiple inverters), set monitored inverter numbers. Bat or solar limited current mode:This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. Mppt function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. The 22-65V type inverter will start up at 25V, and 45-90V type inverter will start up at 49.5V, after start, inverter can still work until 22v or 45v. Current sensor Orientation:Please check the current flow direction arrow on the sensor before use, make sure the connection is correct. Otherwise, inverter will not start up at limit mode. Negative power under AC voltage means power overflow to the grid. Positive means power come from the grid. Clamp Sensor with 2m cable—1pcs;(only available for 2000GTIL2-LCD). Wifi Port for MPPT 1000W/2000W NEW SUN Solar/Wind Grid Tie Inverter Extra cost of 75usd required if. NOTE : this WIFI port must be ordered with 2nd Generation Grid Tie Inverters together. NOTE : It will be built-in side the inverter. Russian buyers were required to fill in the full name; Brazilian buyers are required to leave CPF/CPNJ Number; Chilean buyers are required to leave RUT number. All return products should be in original package with all accessories included. We stand behind our products so you are always covered! The item “2000W LCD Solar Grid Tie Inverter, MPPT pure sine wave built-in limiter optional” is in sale since Saturday, February 03, 2018. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “sunhome910″ and is located in , . This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: Ecopower
MPN: Does Not Apply
Country/Region of Manufacture: China

Category: 2000w | Comments Off

September 7

2000W LCD Solar Grid Tie Inverter, MPPT pure sine wave built-in limiter optional

2000W LCD Solar Grid Tie inverter With built-in power limiter optional, MPPT pure sine wave. 90V to AC 230V. New updated firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter , this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. New developed grid tie inverter(second generation) with different design structure, enable better and stable operation quality. With much better output pure sine. Waveform and better PF Value. 2000G2-LCD—————1000W Grid tie inverter can not work with power limiter. 2000GTIL2-LCD———-1000W grid tie inverter with internal and external limiter function. The inverter is integrated with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter. Mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external. Limiter module working with it. Max input DC voltage. Peak power tracking voltage. 47.5-51.5 for 50hz; 59.3-60.5 for 60hz. Just for AC output. 20’C — +85’C. Great LCD show various parameters. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in. Oscilloscope, PF value also shows in good result, 99.8% PF value. The item “2000W LCD Solar Grid Tie Inverter, MPPT pure sine wave built-in limiter optional” is in sale since Thursday, June 08, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “sunhome910″ and is located in , . This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: Ecopower
MPN: Does Not Apply
Country/Region of Manufacture: China

Category: 2000w | Comments Off

September 1

2000W LCD Solar Grid Tie Inverter MPPT Pure Sine Wave Built-in Limiter Optional

2000W LCD Solar Grid Tie inverter With built-in power limiter optional MPPT pure sine wave. 90V to AC 230V. New developed grid tie inverter(second generation) with different design structure, enable better and stable operation quality. With much better output pure sine. Waveform and better PF Value. 2000G2-LCD—————1000W Grid tie inverter can not work with power limiter. 2000GTIL2-LCD———-1000W grid tie inverter with internal and external limiter function. The inverter is integrated with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter. Mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external. Limiter module working with it. Max input DC voltage. Peak power tracking voltage. 47.5-51.5 for 50hz; 59.3-60.5 for 60hz. Just for AC output. 20’C — +85’C. Great LCD show various parameters. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in. Oscilloscope, PF value also shows in good result, 99.8% PF value. The item “2000W LCD Solar Grid Tie Inverter MPPT Pure Sine Wave Built-in Limiter Optional” is in sale since Tuesday, November 22, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “zcsolar2016″ and is located in , . This item can be shipped worldwide.

Brand: Tricropower
MPN: Does Not Apply
Country/Region of Manufacture: China

Category: 2000w | Comments Off

November 2024
M	T	W	T	F	S	S
« Oct
				1	2	3
4	5	6	7	8	9	10
11	12	13	14	15	16	17
18	19	20	21	22	23	24
25	26	27	28	29	30