Grid Tie Solar Inverter MPPT 1300W Micro Inversor DC 30-45V PV AC 120V/220V 6V

Grid Tie Solar Inverter MPPT 1300W Micro Inversor DC 30-45V PV AC 120V/220V 6V. Grid Tied inverter is a compact unit, which directly converts direct current into alternating current for powering appliances and/or office equipment’s and connecting to utility grid. The AC output from Smart Micro inverter is synchronized and in-phase with the utility grid. Please note that this inverter is specially designed for solar panels and can be applied to 24V solar panels. Vmp is 26-39V and Voc is 34-45V. If a 12v battery is used as input, the inverter will not be able to reach its maximum Power point. We recommend using 36v battery as input source to get better output power. There is always a power loss in the conversion from DC to AC. Energy is also lost through heat. Therefore, if you want to be 100% off the machine, it will not give it to you. Solar panels also have losses, so please do not calculate the efficiency based on the inverter output power/solar panel specifications. Because solar panels and inverters have their own efficiency. Collected fault feedback from multiple customers, most of which stopped working because of the wrong solar panel voltage input. Please use a 10 square cable, the cable length is not recommended to exceed 4M. Tighten the DC terminal wiring. If the cable is too thin or the connection is loose, the inverter will be damaged. The Voltage of Matched solar panel:Vmp: 26-39V, Voc: 34-45V. AC Output Voltage: 120VAC(90-140VAC) or 230VAC(190-260VAC). Frequency Range: 48Hz 62Hz Auto. Vmp(of a solar panel) must be in the MPPT range to ensure the good output efficiency. The Voltage of Matched solar panel. Vmp: 18-21V, Voc: 20-24V. Vmp: 26-39V, Voc: 34-45V. 120VAC(90-140VAC) or 230VAC(190-260VAC). Islanding; Short-circuit; converse connection; Low Voltage; Over Voltage; Over temperature Protection. 1 Red and 1 Green. EN61000-6-3:2007 EN61000-6-1:2007. DIN VDE 1026 UL1741. AC The output need to be connected to the grid power. AC socket: Connection to the mains. The AC cord to the inverter 3 foot outlet, then the AC cord to home 3 pin AC outlet. 4:The switch of the home outlet must be turned on. Stackable connection The purpose is let small power inverter become high-power inverter. In order to achieve higher power use requirements, the use of this product can be stacked, such as: 4 grid inverters 1300W of stack used is equal to 5200W, and the number of open stacks (No Quantitative Restrictions). There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “rodonite-7″ and is located in this country: CN. This item can be shipped worldwide.

Input Voltage: DC 20-45V
Output Voltage: 220-240V
Size: 39*21*11CM
Current Rating: Standard
Model: 5607283102
Country/Region of Manufacture: China
Output Type: Single
Waterproof: Indoor design
Weight: 2.5KG
Current Type: AC/DC
System Configuration: Grid-Tie
Type: On Grid Inverter
Features: Durable
MPN: 5607283131
Power: 1300W
Current Output: Standard
Brand: Unbranded
Application: Home/Garden
Charging Mode: MPPT (Maximum Power Point Tracking)
MPPT voltage: 26V – 36V
Output Current: 75A MAX
Output Frequency: 50HZ/60HZ auto match
Output Power: >1000KW
Resistance Properties: Dustproof
Voltage: AC120V/220V

Category: grid | Comments Off

March 31

Grid Tie Solar Inverter 600W MPPT Inversor DC30-55V AC 120V/220V Home System

Grid Tie Solar Inverter 600W MPPT Inversor DC30-55V AC 120V/220V Home System. Smart grid tie inverter is a compact unit, which directly converts direct current into alternating current for powering appliances and/or office equipments and connecting to utility grid. The AC output from Smart Microinverter is synchronized and in-phase with the utility grid. Solar panels:150W-600W The Voltage of Matched solar panel:Vmp: 26-39V, Voc: 34-46V AC Output Voltage: 120VAC(90-140VAC) or 230VAC(190-260VAC) Frequency Range: 48Hz 62Hz Auto DC Input: 22V-60V MPPT range: 28V – 39V. Vmp(of a solar panel) must be in the MPPT range to ensure the good output efficiency. It will perfect compatible with panels at 30V or 36V (Vmp) Please note that this inverter is designed for solar panels, which can be suitable for 24V, 30V Solar Panels, Vmp is 26-30V and Voc is 34-38V;36V Solar Panels, Vmp is 35-39V and Voc is 42-46V. If customers want to use this inverter for battery, please connect 36V battery for this inverter. If your battery is 24V, you can choose 11-32VDC version. However, we still suggest customers don’t use battery for this inverter, it will influence product life-span. There’s always a loss in power in conversion from DC to AC. Also through Heat loss of energy. So if you’re expecting to get you’re 100 % out of the machine it won’t give you that. Solar panel has the loss too, so please don’t calculate the efficiency as inverter output power/solar panel specification. Because solar panel and invergter all have own efficiency. Please use a 10 square cable, the cable length is not recommended to exceed 4M. Tighten the DC terminal wiring. If the cable is too thin or the connection is loose, the inverter will be damaged. AC The output need to be connected to the grid power. 3:AC socket: Connection to the mains. The AC cord to the inverter 3 foot outlet, then the AC cord to home 3 pin AC outlet. 4:The switch of the home outlet must be turned on. Stackable connection The purpose is let small power inverter become high-power inverter. There may be some delays due to flight, holiday, weather, local post, local natural disaster impact. It must also be in the original packaging. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “rodonite-7″ and is located in this country: CN. This item can be shipped worldwide.

Input Voltage: 22-60V
Output Voltage: 110-120V
Size: 29*15*10CM
Current Rating: Standard
Inverter Technology: Other
Model: 4043865016
Country/Region of Manufacture: China
Connector Type: Other
Maximum Input Power: 600W
Weight: 1.8KG
Custom Bundle: No
Input Voltage:: Vmp: 26-39V, Voc: 34-46V
Wattage: 600W
Current Type: AC
System Configuration: Grid-Tie
Product Line: Grid Tie Solar Inverter
Maximum Input Voltage: 120V/220V
Power Source: Solar
Type: Grid Tie Solar Inverter
Features: Durable
MPN: 4043865046
Recommended Environment: Other
Protection Properties: Other
Power: 600W
Current Output: 9.09A(110V) 5A(220V)
Brand: Unbranded
Application: Other
Maximum Flow Rate: Standard
Charging Mode: Other
Output Frequency: 50HZ/60HZ auto match
Output Power: 500 – 1000W
Output Type: Single
Output Voltage:: 120V(90V~140V)OR230V(190V~260V)
Type:: On Grid Inverter
Resistance Properties: Other
Voltage: 28V – 39V

Category: grid | Comments Off

March 15

600W 700W Solar Grid Tie Micro Inverter MPPT Waterproof Inversor DC26V-46V PV In

600W 700W Solar Grid Tie Micro Inverter MPPT Waterproof Inversor DC26V-46V PV Input AC120V/220V Pure Sine Wave Out Home Solar. 600W 700w Smart Microinverter Pure Sine Wave Power Solar Micro On Grid Tie inverter 24V 36V DC to 110v 220V AC for Solar Panel. Because of the high power, a circuit breaker is required. Regarding the heating problem of the inverter. This is normal phenomenon. All electronic devices generate heat during operation. The inverter uses aluminum alloy material. Metal can conduct heat better. The inverter also has over-temperature protection if the temperature is high. Then the inverter will automatically reduce the working output efficiency. After cooling down, restart. It is recommended to install the inverter in a ventilated, dry and cool place. This is a common problem of micro-inverters. After a large amount of customer data feedback, the inverter cannot work because the DC or AC fuse is damaged. When you encounter this problem, we can send you accessories for free. And give you maintenance video instruction. You can easily replace it. Grid Tie Inverter Using IP65 waterproof streamline design, Can effectively prevent rainwater on the surface erosion. High performance Maximum Power Point TraCKING(MPPT) and Autolock maximum Power Point (APL) Please do not install outdoors, avoid rain. You can install it in a ventilated, dry, cool place. Single unit connects to one PV module. On Grid Tie Inversor Maximum 600W AC output power. Single-phase output, Flexible 3-phase PV systems. 4.2.4G wireless communication and monitoring. Solar Grid Tie Inverter Up to 8 units (230V) per branch. Customizable various input (DC, PV) voltage range. Integrated AC bus cable, Ready-To-Use. On Grid inverter Low cost, Easy installation. Notice: SG-600W/SG-700W internal upgrade. Dual-chip inverter: function and output are independently controlled with faster control speed and higher efficiency. The old version is a single-chip control function and output. Solar micro-inverters Product Parameter. Input Data(DC, PV). Number of Input MC4 Connector. Smart Microinverter Rated Output Power. Default Output Voltage Range. Default Output Frequency Range. Pure Sine Wave inverter Power Factor. Maximum Units per Branch. PV Solar Micro Inverter Peak Efficiency. Operating Ambient Temperature Range. Solar PV inverter Dimensions (W x H x D). 185mm x 180mm x 38.5mm (not include connectors and cable). Max Current of AC Bus Cable. Micro solar Smart Inverter Cooling Mode. Natural Convection – No Fans. Communication(Inverter to DataBox). High Frequency Transformers, Galvanically Isolated. Equipment ground is provided by the PE in the AC cable. No additional ground is required. Isolated Island Protection, Voltage Protection, Frequency Protection, Temperature Protection, Current Protection, etc. NB/T32004:2013, NB/T32004:2013, EN61000-3-2, EN62109, VDE0126, UL1741 etc. Dimensions (W x H x D). Avoid sunlight – when installing an inverter, you need to avoid direct sunlight to cause excessive temperature. Avoid rain – the installation of the inverter needs to prevent rain or other liquid from getting wet or soaking. Keep ventilation -the inverter needs to be installed in a well ventilated environment to facilitate heat emission. Installation Schematic For SG600. Wiring Schematic For SG600. 1: Length 2m 2: AC power cord can only be used for 1PCS inverter. 3: If multiple inverters are connected in parallel, a circuit breaker must be used. Connect to the grid in accordance with L, N, G. 4: Can only be used for SG series 300W-700W. 5: Cannot be used for SG serie 1000W 1200W 1400W. 6: Note that the ground wire cannot be connected incorrectly! This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “topsseller99″ and is located in this country: HK. This item can be shipped worldwide.

MPN: SG-700W
Inverter Technology: Microinverter
Current Type: DC
System Configuration: Grid-Tie
Brand: POWERLAB
Resistance Properties: Waterproof

Category: 600w | Comments Off

February 1

600W 700W Solar Grid Tie Micro Inverter MPPT Waterproof Inversor DC26V-46V PV In

MPN: SG-700W
Inverter Technology: Microinverter
Current Type: DC
System Configuration: Grid-Tie
Brand: POWERLAB
Resistance Properties: Waterproof

Category: 600w | Comments Off

July 17

Solar Inverter 50Hz/60Hz Hybrid Pure Sine Wave PWM Battery Charger inversor Kit

Solar Inverter 50Hz/60Hz Hybrid Pure Sine Wave PWM Battery Charger inversor Kit. The rated power: 3000VA/3000W. 90-280VAC (For Personal Computers), 170-280VAC (For Home Appliances). Frequnecy Range: 50Hz/60Hz (Auto sensing). AC Voltage Regulation Batt. Power factor: 1.0. Transfer Time: 10ms (For Personal Computers), 20ms (For Home Appliances). Wave form: Pure sine wave. Floating Charge Voltage: 27VDC. PWM SOLAR CHARGER & AC CHARGER. Maximum PV Array Power. PWM Range Operation Vol: 18-80VDC. Maximum PV Array Open Circuit Vol. Standby Power Consumption: 28W. Maxmum Solar Charge Current: 50A. Maxmum AC Charge Current: 25A. Products Dimension, DWH(mm): 363297107mm. Packing size, DWH(mm). Net Weight (kgs): N. 5% to 95% Relative Humidity (Non-condensing). Pure sine wave, high frequency technology, wall amounted design, light weighted and easy to operate. Selectable input voltage range for home appliances and personal computers. Selectable charging current based on applications. Configurable AC/Solar input priority via LCD setting. Solar charger and AC charger built inside, Compitable to grid power or generator power. Auto restart while AC is recovering, auto charge and switch, unattended operation. Smart battery charger and management for optimized battery performance. High Efficient DC-To-AC Conversion. Minimizing Energy Loss and self power consumption. All around protection functions: Overload/short circuit protection/high voltage/low battery voltage/high temerature, etc. The item “Solar Inverter 50Hz/60Hz Hybrid Pure Sine Wave PWM Battery Charger inversor Kit” is in sale since Tuesday, June 15, 2021. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “my-family-store” and is located in Shanghai. This item can be shipped worldwide.

Size: 424x390x193mm
Maxmum Solar Charge Current: 50A
Output Current: 50A
Output Frequency: 50Hz
Output Power: 1 – 200KW
Current Rating: N/A
Output Type: Single
Model: 2697341875
Country/Region of Manufacture: China
Custom Bundle: No
Current Type: AC
System Configuration: Grid-Tie
California Prop 65 Warning: There is no harmful effect’s.
Output Voltage: 220-240VAC
PWM Range Operation Voltage: 18-80VDC
Usage A: Inverter 3000W
Usage B: Solar inverter 24v
Weight: 8KG
Type: Charger/Inverter
Features: All Daylight Conditions
MPN: 2697341897
Power: N/A
Current Output: N/A
Brand: Unbranded
Application: Agriculture/Farming
Charging Mode: MPPT (Maximum Power Point Tracking)
Function: Solar inverter 24V 220V
Resistance Properties: Abrasion Resistant
Is Smart Device: YES
Maximum PV Array Open Circuit Voltage: 80VDC
Maximum PV Array Power: 1200W
Maxmum Charge Current: 70A
Voltage: 1000 VAC or Greater

Category: solar | Comments Off

July 25

2000W Solar Grid Tie Inverter with Limiter Connected 45-90V SUN-2000 Inversor

Inversor de lazo de rejilla de 2000 w para paneles solares o batería. Funciona bien con todo tipo de pilas. CON LIMITADOR interno/conexión Wi-Fi. Pinza de sensor limitador Puerto Wi-Fi (opcional). Rango de voltaje de entrada: DC o 45 V-90 V (opcional). Voltaje de salida: ca 220 V 230 V 240 V (automático). ¿Por qué producimos el inversor de conexión de red con limitador? Es En respuesta a la gran presión de nuestros clientes para un producto que puede controlar la cantidad de potencia que ata los inversores de la rejilla (GTI) puede generar para que la cantidad de exceso de energía que producen los paneles solares se reduzca a niveles pequeños, Si no se elimina, porque en algunos países, el productor paga el exceso de potencia que da a la red de distribución. Esto se debe a los medidores de energía eléctrica (el proporcionado por el proveedor de electricidad en la zona) no son conscientes de la dirección del flujo de energía. En otras palabras, solo se añade incluso si la potencia se exporta a la red, por lo tanto, los consumidores serán cargados de energía incluso si se da a la red, Y este es el problema. Este es el inversor de conexión de rejilla de segunda generación con limitador. Con la segunda generación GTIL, integramos la función de límite dentro del GTI. Lo llamamos limitador interno. De esta manera, No se necesita ningún módulo limitador adicional, reduce el costo de los clientes, más fácil de instalar. Pero en caso de que el cliente instale el inversor a distancia Desde el disyuntor principal, también permitimos que el 2 ° GTIL funcione con limitador independiente, A esto se le llama limitador externo. Por supuesto, el inversor puede funcionar bajo la conexión de rejilla normal-Sin Modo de límite, solo tienes que poner en la bonita pantalla LCD y guardar tu Ajuste. Nuevo firmware actualizado que permite la batería o el modelo de Corriente y Potencia del limitador solar. El usuario puede configurar la potencia de salida máxima del inversor, esto puede hacer que el inversor funcione en la conexión del enfriador como desee el usuario y ampliar la vida útil del inversor. El usuario puede configurar el voltaje de arranque/apagado del inversor que puede ser flexible con el Banco de la batería dependiendo A los usuarios les importa y pueden evitar que el banco de baterías se descargue. Función Wi-Fi para monitorizar la planta solar en la aplicación o sitio web. Puerto Wifi para MPPT 1000 W/2000 W nuevo inversor de rejilla Solar. Aplicación de Web/teléfono móvil para monitorización en línea. Potencia de salida continua. Pico de potencia de salida. Voltaje de entrada DC rango de. 45 V 90 V. Potencia de pico de tensión. Voltaje de salida de CA de. Consumo de potencia en espera. Salida de la forma de onda. De onda sinusoidal pura. Sobre la protección actual. Sobre protección de la temperatura. Protección contra polaridad inversa. Dimensiones (a x A x L). Inversor de rejilla Solar con limitador (integrado) —– 1 unidad. B cable de CA (integrado)——– 1 piezas. Abrazadera de sensor limitador y cable de 2 m (integrado) —- 1 piezas. Puerto Wi-Fi (opcional/color negro) — no included. ¿Cómo usar el inversor? Modelo de inversor de conexión de rejilla estándar. 1,1 El inversor de conexión de rejilla convierte la potencia de CC fabricada por paneles solares a CA, se conecta a la rejilla y alimenta toda la potencia disponible de los paneles a la carga de CA. 1,2 Toda la potencia excedente que no necesite la carga se exporta a la red. 1,3 Si la rejilla falla, el inversor de conexión se apagará. Cuando la rejilla vuelva a estar en línea. El inversor de conexión de red volverá a suministrar energía a la carga y cualquier exceso de energía se exporta a la red ¡Otra vez! 1,4 Si el Panel Solar está produciendo menos potencia y el GTI no puede entregar toda la energía necesaria por la carga ¡A continuación, la energía se completará con la rejilla. 1,5 Los medidores de potencia (excepto el medidor inteligente) no son conscientes de la dirección del flujo de energía. El usuario paga la potencia exportada y entregada por la red. Uso del inversor de conexión de red con el modelo de limitador. 2,1 El inversor de conexión de red con limitador proporciona solo la potencia necesaria por la carga y evita la entrega de exceso de potencia por lo tanto, evita el exceso de energía para volver a la red. 2,2 El corazón del inversor de conexión de red con limitador es el módulo limitador (LM). El LM muestra continuamente la potencia necesaria por la carga a través del sensor de corriente conectado después del interruptor de circuito principal ¡! El LM procesará la señal. A continuación, envía la señal al inversor de conexión de red, ¿cuánto potencia se puede entregar a la carga en tiempo real? 2,3 El USUARIO, después de instalar y conectar el GTIL correctamente, no necesita hacer nada y la unidad hará su trabajo automáticamente. Instalación de GTIL CON LIMITADOR interno. 3,1 Esta instalación no requiere un módulo limitador adicional, la instalación es mucho más fácil. Sujeta el cable del sensor de corriente al cable caliente para medir la corriente, el limitador interno detectará automáticamente la potencia de carga y controlará la potencia de salida del inversor, el exceso de energía estará bien controlado. Dispositivo de protección externo 3,2, incluyendo dc y ac SPD (dispositivo de protección contra sobretensiones), dc y ac breaker, se recomienda instalar etc en el sistema. Configuración de limitador en el LCD del inversor. El GTIL incluye tres modos de funcionamiento: funciona como GTI normal sin limitación de potencia. Funciona en modo limitador interno y funciona en modo limitador externo, por favor, haz tu configuración en la pantalla LCD y guárdela, configuración de detalles, por favor, lea el manual GTI. 5 modo de descarga de batería. 6 limitador de especificación de módulo. Medidor de potencia-máximo 9999 w. Bloque de terminales-Max 20A. 4 posiciones-max 2000 w. Señal del sensor de abrazadera-5 v CA máx. Cable de señal DC-5 v CC, máx. Cable máximo de 13mm o pulgadas. CE ROHS SGS certificación VDE. The item “2000W Solar Grid Tie Inverter with Limiter Connected 45-90V SUN-2000 Inversor” is in sale since Thursday, March 5, 2020. This item is in the category “Casa, jardín y bricolaje\Materiales de bricolaje\Suministros eléctricos\Suministros energ. alternativa\Suministros energía solar\Paneles solares y kits”. The seller is “wccsolar” and is located in Sevilla. This item can be shipped worldwide.

Color: Azul
Cantidad de unidades: 1
Configuración del sistema: Atado a la red
País/Región de fabricación: España
Voltaje: 45v-90v
Marca: PlusEnergy
Tipo de unidad: Unidad
Entorno recomendado: Interior
Flexibilidad: Rígido
Descripción del anuncio de conjunto: aparato para vertido cero
Tecnología solar: ON GRID
Anuncio de conjunto: Sí