1000W Watt Solar Micro Grid Tie Power Inverter 110V for Solar Panel 10.5-30V AC

Recommended using solar panels. Solar panel open circuit voltage range. Peak power tracking voltage. Maximum input operating current. Dimensions L× W × H. Reverse transfer, load priority. Red terminal: Connect DC positive, black terminal: Connect DC negative. 2 Input voltage range: 10.5V to 28V. Solar Panel: Recommend using the power more than 30W and the standard voltage of 17.5V PV panel. Recommend using multiple solar panels. Solar panel in series will result in high-input voltage which will exceed the working voltage range of the inverter. Wind turbine system: Rated voltage 24VDC, maximum voltage 28VDC. 2 Voltage range of the inverter whose output is 220V AC. 2 Voltage range of the inverter whose output is 110V AC. A:90140V (USA plug). B:180260V (Australian, British, European Union Plug OPTIONAL). 1Low-voltage protection (input DC voltage is less than 10.5VDC). 2Over-voltage protection (Input DC voltage is greater than 28.5VDC). 3Over-temperature protection when the chassis temperature is above 75. The temperature dropped about 2-10 minutes to restart automatically after cooling. 4Fault Protection (when 110VAC or 220VAC power outage or shutdown). 5Islanding protection: When the electric supply stop, the inverter automatically shut down output. 1Green LED flashing: The inverter is adjusting power output. MPPT is in working condition. 2Green LED long in time: The inverter is in working condition with the maximum output power. Please pay attention of the voltage when use the product. The voltage is from 10.528V, if is not these voltage the product may broken. Non-professionals do not disassemble. Only qualified personnel may repair this product. Please install inverter in the low humidity and well-ventilated place to avoid the inverter over-heating, and clear around the inflammable and explosive materials. When using this product, avoid children touching, playing, to avoid electric shock. Optimal length of the DC input line 8M or less, long cable will allow solar panels to the inverter DC voltage drop caused by wear and tear. Connected to a power outlet to provide AC. Connected solar panels, battery DC input DC power supply cable. One standard AC wire. The item “1000W Watt Solar Micro Grid Tie Power Inverter 110V for Solar Panel 10.5-30V AC” is in sale since Friday, September 18, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “lawkia-2″ and is located in CA. This item can be shipped to United States.

Brand: Unbranded
MPN: Does Not Apply

Category: 1000w | Comments Off

November 10

1000W DC22-45V to AC110V MPPT Pure Sine Wave Inverter For Wind Turbine Generator

1000W Grid Tie Inverter 110V Output MPPT Pure Sine Wave Inverter Power for Solar. Creative MPPT technology, efficiency more than 99%. Parallel type design for DC input and modularization design. Small volume, distributed installation, easy for system configuration. Adopting high-frequency isolation transformer type, high efficiency. Perfect electrical protection function. Stackable and Easy to install. Grid tie inverter is a device which directly converts direct current into alternating current which. Sine wave, frequency and phase. Are same as power grid and then feed into utility grid. It is a key. Device of power generation systems such as PV power generation system. Smart Microinverter specially optimized design to work with modularization of DC power supplies which includes the mainstream solar modules, 24V (60 cells) and. 36V (72 cells) monocrystal and/or Polycrystalline solar panels. Smart Microinverters are stabilization, reliable and high conversion efficiency items. It is best choice for PV. Smart Microinverter can be easily placed and attached to the rack underneath of PV module. Need spaces for independent installation and low voltage DC wire connects from the PV module to. Smart Microinverter can eliminate the risk of high DC voltage. Philosophy for Smart Microinverterl insures the productiveness of the whole system and will not. Affect by a single point of failure. Each Smart Microinverter is individually connected to one PV. Module in the array. Each PV module has the individual Maximum Peak Power Point Tracker. Control and insures the maximum power is exported to the utility grid regardless of the. Performance of the other PV modules in the array. When PV modules in the array under non-ideal. Conditions in practical applications such as PV modules are affected by shading, soiling. Orientation, or mismatch, Smart Microinverter insures top performance for maximizes energy. Production from the whole PV system and gets return on investment in less time. Advantages of Smart Microinverter. Unique circuit design, choice of import industrial electronic components, higher efficiency, more. Creative MPPT technology, efficiency more than 99%, faster and more sensitive reaction, more. Parallel type design for DC input and modularization design for inverter, small volume, distributed. Installation, easy for system configuration, flexible for combination, strong expansibility of system. Adopting high-frequency isolation transformer type, high efficiency, and high security. Aluminum alloy housing, not rust, heat-resisting and cold-resistant as well as anti-corrosion. Getting electronic circuit design, appearance design and other core technology patents. What’s In Box. 1 x 1000W Grid Tie Inverter. 1 x User’s Manaul. 1 x AC US Cord. The item “1000W DC22-45V to AC110V MPPT Pure Sine Wave Inverter For Wind Turbine Generator” is in sale since Friday, August 21, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “ronoe_1231″ and is located in Hebron, Kentucky. This item can be shipped to United States.

MPN: Does Not Apply
Voltage: 24-36V
Brand: Unbranded
Rated Power: 1000W
DC Input Range: 20V-45V
AC Output: 110V(90-140V)
THD: <5%
Stand-by Power: 1W
Solar Panels: 60/72 cells ; 30V/36V
MPPT Voltage: 26-36VDC
Frequency: 48Hz-62Hz
Power Factor: >97.5%
Certification: CE RoHS

Category: 1000w | Comments Off

November 10

1000W Grid Tie power inverter DC46V-112V / AC110V, solar panel, mppt, USA stock

1000W on Grid Tie Power Inverter. Pure sine wave micro grid tie inverter. For 48V-60V solar system, DC 46V-112V to AC 90V-130V. Important note: on grid tie inverter, it need to plug into your home grid, CAN’T power your device directly. For 48V-60V solar system, the best working voltage(MPPT) is about 80V-96V. Multi-protection function: Over Current Protection/Over Temperature Protection/Reverse Polarity Protection/Island Protection. Features: Stackable/MPPT-Maximum Power Point Tracking/Automatic Sensing Function Solar Luminosity and restart automatic every morning. Safety: DC and AC all have fuse to protect the people + power switch +we do the speical for the aluminum shell, it is insulation. Cooling method: fan-cooled w/aluminum shell, more better cooling function, smart and light, easy to carry and handle. The grid tie power inverter can obtain the solar energy from solar panels, and can tie to the grid through its output cable without extra equipment. The installation is very convenient and reliable. This smart grid tie inverter can connect with mono silicon, polygon silicon, non-crystal film that can transform solar energy to home grid. The power of grid tie solar panels, it can be standardization according to the actual using. The inverter can be connected to any home AC outlet, when this line runs by the conventional electric network. This grid tie inverter monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase are as same as the grids, and the volume is a bit higher than the grids, then according to the current controlled PWM, to control the output power to the grid. The inverter just outputs power when the home grid is on. In the day time, solar panels will produces DC voltage, and thus inverter will change the DC voltage to AC voltage and outputs power to home grid system. During the night, inverter will be standby mode and led light will be red, and inverter will back to work in the day time when inverter detects the input voltage is up to working voltage. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. There are many advantages of grid tie inverter compare with the traditional grid tie system. Low cost and easy installation this inverter can make full use of all types of buildings/houses surface that face to the sun in the city as well as fast and easy installation of solar models and grid tie inverter. Its very low maintenance costs. Free combination this inverter can be used as a separate grid tie system and can be setup as a large solar array with many of them (stackable). The quantity of the inverter in the array is just according to your demands. If you are planning to install a grid tie PV system, in a general way, the solar array and inverter need to be carefully matched to ensure that the inverters on load voltage and power limits are not exceeded. When you want to increase more solar panels, and if the total power of the solar panels exceeds the allocation grid tie inverter, it is necessary to add more grid tie inverters. Combination of grid tie inverters will not interact The traditional solar grid tie system, they offer units ranging in high power output and these units are modular so you can have multiple units operating in parallel for large solar arrays. Although, the traditional grid inverter has MPPT feature (Maximum Power Point tracking), but the maximum power point is according to the entire series in terms of solar panels array, if the performance of a piece of solar panels in the system, for some reason, like dust, shadow… The performance of the entire solar power system will decrease. This inverter has no such disadvantage. If the performance of a piece of solar panels in the system degrades, this just effects this piece itself, will not affect others in the system. Improving the efficiency of the entire solar power system in traditional grid tie system, the solar panels are connected in series, so the MPPT of the inverter is according to the total panels in series, not to every panel, but there is difference between every panel, so not every panel is working at the maximum power, this will reduce the total power of these panel in series. But this inverter has no such disadvantage. Because every inverter has MPPT function, so every panel is working at the maximum power, this will increase the efficiency of the entire system. Low power consumption most of the parts in the grid tie inverter are digital ICs and low power MCU, so the power consumption of it is low, though the quantity of grid tie inverters is increased, but this will not increase the power consumption of the entire system. The individual system of the inverter is shown in Figure 1. Installing the solar panel with DC input terminals of the grid tie inverter, and inverter AC side is power cord with plug, just plug into home AC grid socket. Connect solar panels with inverters DC terminals, inverter AC side connect to home AC grid source, then turn on inverter to start work. Please connect with correct home Ac source, if inverter is AC 180v-260v, then must connect with home AC 280v-260v outlets, inverter will not work for wrong voltage. The LED indicator will start to light when the grid and DC supply is detected. This indicates the inverter is operating under normal condition. The rate of the cycling is according to how much power is being input from the solar panels. The more input power, the led light will flash fast. If there is no Ac grid detected, the red LED will be on, the inverter will not output, this is called Island protection to avoid damage of PCB boards. Note: this inverter is designed for solar panel, please do not use with wind turbine, thanks. Normal Ac output power. Maximum AC output power. DC Input Voltage range. DC 46V-112V (solar panel). AC Output Voltage range. Total harmonic distortion(THD). MPPT function / Stackable. Dimensions (L x W x H /cm). 33.519.513.5cm. International buyers Please Note. The item “1000W Grid Tie power inverter DC46V-112V / AC110V, solar panel, mppt, USA stock” is in sale since Monday, September 2, 2019. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “solarleader2016″ and is located in dong guan. This item can be shipped to United States.

Model: 1KW-GT-46-112-110
Country/Region of Manufacture: China
Wattage: 1000W
System Configuration: Grid-Tie
Power Source: Solar
Voltage Input: 46V-112V
MPN: do not apply
Recommended Environment: Indoor/Outdoor
Voltage Output: 110V
Brand: SOLINBA

Category: 1000w | Comments Off

November 7

1000W Solar Grid Tie Inverter with Power Limiter DC26-60V to AC110V/220V Auto

You may also like. 1000W Solar Grid Tie Inverter MPPT DC20-45V to AC110V for 24V/30V/36V PV Panel. 600W Grid Tie Inverter DC22-60V for 30V/36V Solar Panel Pure Sine Wave Inverter. 1000W Grid Tie Inverter MPPT DC10.8-30V to AC110V Solar Pure Sine Wave Inverter. 600W Solar Grid Tie Inverter AC110V for 30V/36V PV Panel Pure Sine Wave Inverter. 1000W Grid Tie Inverter DC10.8-30V to AC110V for 12V Solar Panel Microinverter. 600W MPPT Grid Tie Inverter DC11-32V to AC110V for 12V Solar Panel/24V Battery. 2000W Grid Tie Inverter with Limiter Sensor MPPT Stackable DC45-90V to AC190-260. MPPT 600W Grid Tie Inverter AC110V for 30V/36V PV Panel Pure Sine Wave Inverter. 600W Solar Grid Tie Inverter MPPT DC22-60V to AC110V Pure Sine Wave Inverter CE. 1000W Solar Grid Tie Inverter with Power Limiter Sensor DC26-60V to AC190-260V. Grid Tie Inverter DC Input 22-60V(Starting Voltage 26V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 60V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 22-60V model inverter will start up at 26V, after starting, the inverter can work in 22V-60V. Solar Panel Voc cannot be higher than 60V. Vmp 30v-48v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). Rated Power (Peak/Continuous): 1000W / 900W DC Input Voltage: 22V60V Peak Power Tracking Voltage: 2654V AC Output Voltage Range:110V/220V Auto Grid Tie Power Inverter starting voltage 26V AC Output Frequency Range: 46Hz65Hz Stackable: Just for AC Output Output Wareform: Pure sine wave. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W Solar Grid Tie Inverter with Power Limiter DC26-60V to AC110V/220V Auto” is in sale since Monday, July 20, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “maihuiyan” and is located in CA. This item can be shipped to United States.

Model: Grid Tie Inverter with Power Limiter Sensor
Stackable: Just for AC Output
Color: Blue
MPN: Does Not Apply
Recommended Environment: Indoor
Brand: Y&H
Application: Home/Garden
Inverter Technology: Microinverter
Country/Region of Manufacture: China
System Configuration: Grid-Tie
Power Source: Solar
Features: Bluetooth Module
Power: 1000W
AC Output Frequency Range: 46Hz~65Hz
AC Output Voltage Range: 190~260V
DC Input Voltage: DC22V~60V
Grid Tie Power Inverter starting voltage: 26V
Output Wareform: Pure sine wave
Peak Power Tracking Voltage: 26~54V

Category: 1000w | Comments Off

November 5

1000W MPPT Solar Grid Tie Inverter with Power Limiter Sensor DC 45-90V / 26-60V

You may also like. 1000W Grid Tie Inverter AC110V Used for 12V Solar Panel Pure Sine Wave Inverter. 1000W Grid Tie Inverter MPPT Stackable DC20-45V to AC110V Pure Sine Wave Inverte. 600W Grid Tie Inverter MPPT Stackable DC20-60V to AC110V Pure Sine Wave Inverter. 1000W MPPT Grid Tie Inverter DC10.8-30V to AC110V Solar Pure Sine Wave Inverter. 1000W Grid Tie Inverter DC20-45V to AC110V for 30V/36V PV Panel Solar Inverter. 600W Grid Tie Inverter MPPT Stackable DC11-32V to AC110V Pure Sine Wave Inverter. 600W Grid Tie Inverter DC22-60V for 24V/36V Solar Panel Pure Sine Wave Inverter. 600W Grid Tie Pure Sine Wave Inverter 110V Used for 12V Solar Panel/24V Battery. 2000W MPPT Grid Tie Inverter with Power Limiter Stackable DC45-90V to AC190-260V. 10A/20A/30A PWM Solar Charge Controller for 12V 24V Lead Acid/Lithium Battery. 1000W MPPT Solar Grid Tie Inverter with Power Limiter Sensor DC 45-90V / 26-60V. Grid Tie Inverter DC Input 22-60V(Starting Voltage 26V) / 45-90V(Starting Voltage 49.5V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 60V / 90V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. Intelligent LCD display various parameters. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 22-60V model inverter will start up at 26V, after starting, the inverter can work in 22V-60V. Solar Panel Voc cannot be higher than 60V. Vmp 30v-48v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). Rated Power (Peak/Continuous): 1000W / 900W DC Input Voltage: 22V60V Peak Power Tracking Voltage: 2654V AC Output Voltage Range:110/220V Auto Grid Tie Power Inverter starting voltage 26V AC Output Frequency Range: 46Hz65Hz Stackable: Just for AC Output Output Wareform: Pure sine wave. Rated Power (Peak/Continuous): 1000W / 900W DC Input Voltage: 45V90V AC Output Voltage Range: 110/220V Auto Peak power tracking voltage: 49.582V AC Output Frequency Range: 46Hz65Hz Peak Inverter Efficiency: 92% Stackable: Just for AC Output Output Wareform: Pure sine wave. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W MPPT Solar Grid Tie Inverter with Power Limiter Sensor DC 45-90V / 26-60V” is in sale since Wednesday, July 22, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “eprec-us” and is located in CA. This item can be shipped to United States.

AC Output Voltage Range: 110V/220V Auto
Brand: Y&H
Color: Blue
Country/Region of Manufacture: China
DC Input Voltage: 45V~90V / 26-60V
Frequency Range: 50Hz~60Hz Auto
Model: 1000W Grid Tie Inverter with Limiter Sensor
MPN: Does Not Apply
Output Wareform: Pure sine wave
Power Source: Solar
Stackable: Just for AC Output
System Configuration: Grid-Tie
Voltage: DC 45-90V / 26-60V
Wattage: 1000W

Category: 1000w | Comments Off

October 25

1000W Solar Grid Tie Inverter with Power Limiter Sensor DC22-60V, AC110/220V Auto

You may also like. 1000W Grid Tie Inverter DC10.8-30V or DC20-45V to AC110V Pure Sine Wave Inverter. MPPT 600W Grid Tie Inverter Pure Sine Wave DC22-60V Solar Input AC110V Output CE. 600W Grid Tie Inverter DC11-32V to AC110V MPPT Pure Sine Wave Micro Inverter CE. 1000W Solar Grid Tie Inverter 110V for 24V/36V PV Panel Pure Sine Wave Inverter. 1000W Grid Tie Inverter Stackable DC10.8-30V to AC110V Pure Sine Wave Inverter. 1000W Solar Grid Tie Inverter with Power Limiter Sensor DC45-90V, AC110/220V Auto. 2000W Grid Tie Inverter with Power Limiter MPPT Stackable DC45-90V to AC190-260V. 1000W Solar Grid Tie Inverter with Power Limiter Sensor DC22-60V, AC110/220V Auto. Grid Tie Inverter DC Input 22-60V(Starting Voltage:26V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 60V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. Intelligent LCD display various parameters. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 22-60V model inverter will start up at 26V, after starting, the inverter can work in 22V-60V. Solar Panel Voc cannot be higher than 60V. Vmp 30v-48v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). Rated Power (Peak/Continuous): 1000W / 900W. DC Input Voltage: 22V60V. Peak Power Tracking Voltage: 2654V. AC Output Voltage Range. Grid Tie Power Inverter starting voltage:26V. AC Output Frequency Range: 46Hz65Hz. Stackable: Just for AC Output. Output Wareform: Pure sine wave. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W Solar Grid Tie Inverter with Power Limiter Sensor DC22-60V, AC110/220V Auto” is in sale since Tuesday, September 22, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “solarlive03yh” and is located in CA. This item can be shipped to United States.

Model: Grid Tie Inverter with Limiter
Rated Power (Peak/Continuous): 1000W / 900W
Stackable: Just for AC Output
Color: Blue
MPN: Does Not Apply
Brand: Y&H
Application: Home/Garden
Inverter Technology: Microinverter
Country/Region of Manufacture: China
System Configuration: Grid-Tie
Power Source: Solar
Power: 1000W
Charging Mode: MPPT (Maximum Power Point Tracking)
AC Output Frequency Range: 46Hz~65Hz
AC Output Voltage Range: 110V/220V Auto
DC Input Voltage: 22V~60V
Grid Tie Power Inverter starting voltage: 26V
Output Wareform: Pure Sine Wave
Peak Power Tracking Voltage: 26~54V
Voltage: DC22-60V

Category: 1000w | Comments Off

October 16

1000W Solar Grid Tie Inverter with Power Limiter Sensor DC45-90V, AC110/220V Auto

You may also like. 1000W Grid Tie Inverter DC10.8-30V or DC20-45V to AC110V Pure Sine Wave Inverter. MPPT 600W Grid Tie Inverter Pure Sine Wave DC22-60V Solar Input AC110V Output CE. 600W Grid Tie Inverter DC11-32V to AC110V MPPT Pure Sine Wave Micro Inverter CE. 1000W Solar Grid Tie Inverter 110V for 24V/36V PV Panel Pure Sine Wave Inverter. 1000W Grid Tie Inverter Stackable DC10.8-30V to AC110V Pure Sine Wave Inverter. 1000W Solar Grid Tie Inverter with Power Limiter Sensor DC22-60V, AC110/220V Auto. 2000W Grid Tie Inverter with Power Limiter MPPT Stackable DC45-90V to AC190-260V. 1000W Solar Grid Tie Inverter with Power Limiter Sensor DC45-90V, AC110/220V Auto. Grid Tie Inverter DC Input 45-90V(Starting Voltage49.5V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 90V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. Intelligent LCD display various parameters. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 45-90V model inverter will start up at 49.5V, after starting, the voltage will drop to 45V, then inverter can work in 45-90V. Voc 60-90V solar panels in parallel is suggested. For example:Voc=36V solar panel, we suggest 2 panels in series, then connect 2 or more groups in parallel. Rated Power (Peak/Continuous): 1000W / 900W DC Input Voltage: 45V90V AC Output Voltage Range:110V/220V Auto Peak power tracking voltage: 49.582V AC Output Frequency Range: 46Hz65Hz Peak Inverter Efficiency: 92% Stackable: Just for AC Output Output Wareform: Pure sine wave. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W Solar Grid Tie Inverter with Power Limiter Sensor DC45-90V, AC110/220V Auto” is in sale since Tuesday, September 22, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “solarlive03yh” and is located in CA. This item can be shipped to United States.

Inverter Technology: Microinverter
Model: Grid Tie Inverter with Limiter
Country/Region of Manufacture: China
System Configuration: Grid-Tie
Power Source: Solar
Color: Blue
MPN: Does Not Apply
Recommended Environment: Indoor
Power: 1000W
Brand: Y&H
Application: Home/Garden
Charging Mode: MPPT (Maximum Power Point Tracking)
AC Output Frequency Range: 46Hz~65Hz
AC Output Voltage Range: 110V/220V Auto
DC Input Voltage: 45V~90V
Output Wareform: Pure Sine Wave
Rated Power (Peak/Continuous): 1000W / 900W
Stackable: Just for AC Output
Voltage: DC45-90V

Category: 1000w | Comments Off

October 16

1000W Solar Grid Tie Inverter withPower Limiter DC45-90V Pure Sine Wave Inverter

1000W Solar Grid Tie Inverter w/Power Limiter DC45-90V Pure Sine Wave Inverter. Grid Tie Inverter DC Input 45-90V(Starting Voltage49.5V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 90V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. Intelligent LCD display various parameters. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 45-90V model inverter will start up at 49.5V, after starting, the voltage will drop to 45V, then inverter can work in 45-90V. Voc 60-90V solar panels in parallel is suggested. For example:Voc=36V solar panel, we suggest 2 panels in series, then connect 2 or more groups in parallel. Rated Power (Peak/Continuous): 1000W / 900W DC Input Voltage: 45V90V AC Output Voltage Range:110V/220V Auto Peak power tracking voltage: 49.582V AC Output Frequency Range: 46Hz65Hz Peak Inverter Efficiency: 92% Stackable: Just for AC Output Output Wareform: Pure sine wave. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W Solar Grid Tie Inverter withPower Limiter DC45-90V Pure Sine Wave Inverter” is in sale since Friday, August 14, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “eprec-us” and is located in shenzhen. This item can be shipped worldwide.

Output Wareform: Pure Sine Wave
Model: Grid Tie Inverter with Limiter
Color: Blue
MPN: Does Not Apply
Recommended Environment: Indoor
Brand: Y&H
Application: Home/Garden
Inverter Technology: Microinverter
Country/Region of Manufacture: China
System Configuration: Grid-Tie
Power Source: Solar
Power: 1000W
Charging Mode: MPPT (Maximum Power Point Tracking)
Rated Power (Peak/Continuous): 1000W / 900W
DC Input Voltage: 45V~90V
AC Output Voltage Range: 190V~260V
AC Output Frequency Range: 46Hz~65Hz
Voltage: DC45-90V
Stackable: Just for AC Output

Category: 1000w | Comments Off

October 12

1000W MPPT Solar Grid Tie Inverter with Power Limiter DC22-60V, AC110V/220V Auto

1000W MPPT Solar Grid Tie Inverter with Power Limiter DC22-60V, AC110V/220V Auto. Grid Tie Inverter DC Input 22-60V(Starting Voltage:26V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 60V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. Intelligent LCD display various parameters. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 22-60V model inverter will start up at 26V, after starting, the inverter can work in 22V-60V. Solar Panel Voc cannot be higher than 60V. Vmp 30v-48v Solar panels connected in Parallel suggested, for example : 4 pcs 200-260w (Vmp 31v solar panels in parallel). Rated Power (Peak/Continuous): 1000W / 900W. DC Input Voltage: 22V60V. Peak Power Tracking Voltage: 2654V. AC Output Voltage Range. Grid Tie Power Inverter starting voltage:26V. AC Output Frequency Range: 46Hz65Hz. Stackable: Just for AC Output. Output Wareform: Pure sine wave. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W MPPT Solar Grid Tie Inverter with Power Limiter DC22-60V, AC110V/220V Auto” is in sale since Friday, August 14, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “eprec-us” and is located in shenzhen. This item can be shipped worldwide.

AC Output Frequency Range: 46Hz~65Hz
Stackable: Just for AC Output
Output Wareform: Pure Sine Wave
Model: Grid Tie Inverter with Limiter
Color: Blue
MPN: Does Not Apply
Brand: Y&H
Application: Home/Garden
Inverter Technology: Microinverter
Country/Region of Manufacture: China
System Configuration: Grid-Tie
Power Source: Solar
Power: 1000W
Charging Mode: MPPT (Maximum Power Point Tracking)
Rated Power (Peak/Continuous): 1000W / 900W
DC Input Voltage: 22V~60V
Peak Power Tracking Voltage: 26~54V
AC Output Voltage Range: 110V/220V Auto
Voltage: DC22-60V
Grid Tie Power Inverter starting voltage: 26V

Category: 1000w | Comments Off

October 8

1000W Grid Tie Inverter with Power Limiter Sensor DC45-90V to AC110V/220V Auto

1000W Grid Tie Inverter with Power Limiter Sensor DC45-90V to AC110V/220V Auto. Grid Tie Inverter DC Input 45-90V(Starting Voltage 49.5V). Grid Tie Inverter with Limiter Sensor. Delivers only the power needed by the load. Voc (solar panel) must not exceed 90V to ensure good output efficiency. Battery discharge power mode, Can auto regulate depth of discharge of the battery bank. Micro Inverter Max Power Point Tracking and AC Stackable, Anti-island protection. Intelligent LCD display various parameters. 1000W Grid Tie Inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. Smart Micro inverter is synchronized and in-phase with the utility grid. The electric apparatus in the house will use power from the inverter first. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inverter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. The 45-90V model inverter will start up at 49.5V, after starting, the voltage will drop to 45V, then inverter can work in 45-90V. Voc 60-90V solar panels in parallel is suggested. For example:Voc=36V solar panel, we suggest 2 panels in series, then connect 2 or more groups in parallel. Rated Power (Peak/Continuous): 1000W / 900W DC Input Voltage: 45V90V AC Output Voltage Range: 190V260V Peak power tracking voltage: 49.582V AC Output Frequency Range: 46Hz65Hz Peak Inverter Efficiency: 92% Stackable: Just for AC Output Output Wareform: Pure sine wave. 1 x On Grid Inverter with Limiter(built-in) 1 x AC cable 1 x Internal type Limiter clamp with sensor & 2m cable 1 x English User Manual. Stackable connectionThe purpose is let small power inverter become high-power inverter. Installation of GTIL With Internal Limiter. How to use the Power Limit function? Connects/clamps to one hot wire after the Main Circuit Breaker. Converts the magnetic field created by the flow of current in the wire into small AC voltage and current which is proportional to the power that passes through the wire. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to one of the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. Bat or solar limited current mode. This function is usable while using with battery. The setted voltage will be the cut off voltage, this means while battery discharged to the setted voltage point or below setted point, inverter will auto disconnect from the battery and stop operating. This can prevent the battery from over discharged. The setted current means inverter will discharge the battery at this current level. MPPT function of the inverter will auto invalid when working under this setting. Set is 0.1V/step. Set is 0.1V/Step. Sellers are not responsible for service transit time. Transit times are provided by the carrier, exclude weekends and holidays, and may vary with package origin and destination, particularly during peak periods. (Only for Business Express). Feedback is very important to us. Please do not give us any bad feedback. If you can do as we say, we will be very grateful. Please give us the opportunity to resolve any problem. The item “1000W Grid Tie Inverter with Power Limiter Sensor DC45-90V to AC110V/220V Auto” is in sale since Friday, July 24, 2020. This item is in the category “Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters”. The seller is “solarlive03yh” and is located in shenzhen. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Australia.

Model: 1000W Limiter Grid Tie Inverter
Peak Inverter Efficiency: 92%
Stackable: Just for AC Output
MPN: Does not apply
Brand: Y&H
Country/Region of Manufacture: China
Wattage: 1000W
System Configuration: Grid-Tie
Output Wareform: Pure sine wave
Rated Power (Peak/Continuous): 1000W / 900W
DC Input Voltage: 45V~90V
AC Output Voltage Range: 190V~260V
Peak power tracking voltage: 49.5~82V
AC Output Frequency Range: 46Hz~65Hz
Voltage: DC45-90V

Category: 1000w | Comments Off

April 2025
M	T	W	T	F	S	S
« Mar
	1	2	3	4	5	6
7	8	9	10	11	12	13
14	15	16	17	18	19	20
21	22	23	24	25	26	27
28	29	30