2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor

For new energy products , we are more professional. NEW 2000W Wind Power Grid Tie Inverter. With dump load controller and resistor. -Max Efficiency:>92% MPPT Efficiency:99%. -AC 220V 230V 240V 50hz 60hz Automatic. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire solar power system. Overload protection , Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD<5%, PF>99%. Build in dump load function. Build in Limiter (internal type). Introduction of Sunshine Grid Tie Inverter for Wind Turbine. The Wind Grid Tie Power Inverter is the worlds most technologically advanced inverter for use in utility-interactive applications. This manual details the safe installation and operation of the The Wind Grid Tie Inverter. This integrated system maximizes energy harvest, increases system reliability, and implifies design, installation and management. The small type wind grid tie power inverter can obtain the wind energy from wind turbine, and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. We call the system combining with small grid tie inverter and wind turbine as SGWT. The system includes wind turbine and small grid tie inverter and installation kit, and some SGWT also will include controller, dump load resistor. The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to control the output. Power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these. Power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. Input Voltage Range 45-90vdc (test point is at the output of the inside rectifier) , Peak power tracking voltage: 50-90v , Max output power:2000w , Nominal Voltage Range: 185-265v , Max Efficiency:>92% , MPPT Efficiency:99%. If DC input type invert. Er , there is only two input connection terminato. Input AC/DC Voltage Range. AC Output Voltage Range. Dimensions (W x H x D). Note: this is 2000w wind power grid tie inverter with limiter. Wind power grid tie inverter —- 1pcs , 2. Dump load resistor —1pcs , 3. AC cable –1pcs , 4. Limiter sensor/clamp / cable —- 1 set. Wind Grid Tie Inverter Installation. Considering the total capacity of the grid tie power system that you need. The total capacity of the whole grid tie power system is according to your power consumption in the site that you want to install, or how much power that you want it to feed to the utility grid. Actually, the volume is just according to your willingness, because when the total power of electric appliances that are being used in the installation site is larger than the output power of the grid tie power system, these power from the system will be consumed in the site, this will slow down the power meter, otherwise, the difference of the output power from the system between the total used power of the appliances will feed to the utility grid. For example, if you want to install a grid tie power system in your house, you could decide the total power volume according to the total power the appliances that you use in your house, maybe the consumption of total energy in per day is about 5KWH, then you should realize the averaged speed of the wind in per day at your site, check the power to the speed of the wind curve from the specifications of the wind turbine, then you can estimate the average power that the wind turbine can generate, actually the real average power the wind turbine can generate at your side is not easy to estimate, you need to check the history data of the climate, because it will vary every day according to the climate, just assume a 1KW rated wind turbine is suitable for the grid tie power system that you plan to set, with this capacity of the system, it can supply all power consumption in whole year. When grid tie power system is working, sometimes, there is extra power feed to utility grid if the power from the grid tie system is larger than the power consumed by the appliances in your house, and sometimes will not when it is not larger. If you use a 1KW wind turbine, then we call the GTWT system is 1KW grid tie power system, of course, you can install 500W grid tie power system or 2KW grid tie inverter, even more large capacity or more small capacity grid tie inverter, it doesnt matter. The capacity is too big, you should consider the volume of AC system of your house can hold the feeded power. Choosing applicable wind turbine for Sunshine Grid Tie Inverter. The most kinds of specifications that the factories marked about the wind turbines. 1, Starting wind speed(m/s). 2, Cut-in wind speed(m/s). 3, Rated wind speed(m/s). 6, Safe wind speed(m/s). 7, Rated DC voltage. You need to choose a wind turbine that the rated power can meet the power consumption. When you choose a wind turbine, you also need to consider ahead what. Model gird tie inverter of SUN series you want to use. Wind turbines have two output type. One is AC output type, and another is DC output type, if the wind turbine is DC output type. It must be integrated with a rectifier. So if the wind turbine is AC output type, you should. Use WAL model of SUN series grid tie inverter, if the wind turbine is DC output type, then. You should use WDL model of SUN series grid tie inverter. Selecting accessory for installation of the Grid Tie Power System. The accessory for grid tie power system including. 1, Connecting cables will be connected with wind turbine and inverters. 4, Power meter(Optional). 5, Bracket for wind turbine installation(not included in this user manual). Selecting correct model of Sunshine Grid Tie Inverter. When finished step1 to step3, then you can select a correct model of SUN series inverter. If the wind turbine is DC output type, then you should choose WDL model inverters, and. The input DC voltage range of the inverter should fit the DC output voltage of the wind. Turbine, the rated power of the inverter should also fit the max. Power of the wind turbine. And the AC output of the inverter should fit the standard of AC utility grid. If the wind turbine is AC output type, then you should choose WAL model inverters. Factories dont supply the AC rated voltage, just supply DC rated voltage, so our WAL also. Supply the DC input range, please check the DC rated voltage of wind turbine should fit. The DC input range of the grid tie inverter. Installing wind turbine to suitable place. Installing the wind turbine of the SGWT to suitable location where the wind is strong enough. To drive the wind turbine. Warning: Please read the user manual of wind turbine before you install the wind. Turbine, dont install the wind turbine under high wind. Warning: Ensure using strong braket to fix the wind turbine to avoid the danger under. Warning: The blades of the wind turbine should be taken down before the hurricane is. Installing Sunshine Grid Tie Inverter to suitable place. Place the Grid Tie Inverter on a surface protected from direct sunlight, high. The inverter requires at least 150mm of clearance around itself for. The inverters are for indoor use, cant use at outdoor. You can use screws to fix. The inverter to the surface, because some models of Sunshine grid tie inverter have fans on. The bottom cover, so the surface should be flat. Connecting Sunshine Grid Tie Power System with cables and connectors. Connecting the Grid Tie Power System with Cables and Connectors. After finished from Step1 to Step6, you should connect the wind turbine and inverter with cables. And connectors to integrate the Sunshine Grid Tie System. Connect the ground terminal of the wind turbine to the NEC approved AC grounding electrode. Connect the grid tie inverters to the grounded racking using a grounding washer approved for the. The ground wire of the AC cables is connnected to the housing of inverter when the AC. Cables is connected to the inverters, so when the AC plug is inserted to the socket of AC outlet of. Utility grid in the house, the ground pin of the socket must be connected to the Earth ground. Connecting the wind turbine output cables after complete from Step1 to Step8. Warning: Before connect the wind turbine output cables to grid tie inverter, you should stop. The the rotating of the wind turbine just in order to avoid the sparkle when connect the cables. WAL model of grid tie invereter connected with AC output type of wind turbine. Connecting two 1000G2-WAL with a max. Power is 2KW wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. GAIA NEW ENERGY is your trusted partner for long term business. We arethe MANUFACUTER of the solar inverter. We are responsible forthe quality of the inverter. The inverter has 2 years guarantee. All return items must be in their original condition. Please do contact with us for return address, details and any other issues. It may not apply to countries with different tariff rules. Please leave us message if you have any question, we will reply in 24 hours, thank you! The item “2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor” is in sale since Sunday, February 26, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “new-power2010″ and is located in ShangHai. This item can be shipped worldwide.

Brand: SUN
MPN: SUN-2000G2WAL-R
Country/Region of Manufacture: China
Power Type: 3 Phase Wind Turbine/Generator
Dump Load Controller: Built-in
Dump load resistor: Included
Display: LCD
Max. Power Output: 2000w
Input AC/DC Voltage Range: 45-90v
AC Output Voltage Range: 185-265VAC auto
Output Frequency: 46Hz~65Hz
Standby Power Consumption: <0.5W
Total Harmonic Distortion: <5%
Peak Inverter Efficiency: 92%
Power Factor: 0.99
Output Wave Form: Pure Sine Wave
MPPT Efficiency: 99%
Over Current Protection: Yes
Over Temperature Protection: Yes
Reverse Polarity Protection: Yes
Anti-Island Protection: Yes
Stackable: Yes
Weight ( Kg): 5.9kg
Dimensions (W x H x D): 469x196x88mm
Featurer Function: Limiter

Category: 2000w | Comments Off

February 6

Preston Stroud New Power Jack Grid Tie Inverter With Missouri Wind And Solar Charge Controller

Category: preston | Comments Off

December 3

1000w Grid Tie Inverter With 250w Buck Step Down Controller

Category: 1000w | Comments Off

May 1

500W Wind Turbine Grid Tie Power Inverter AC 90V-130V Dump Load Controller 12VDC

Wind Grid Tie Inverter. 300W 10.8-30VAC to 110V. 300W 10.8-30VDC to 110V. 500W 10.8-30VAC to 110V. 500W 10.8-30VDC to 110V. 500W 22-60VDC to 110V. 1000W 22-60VDC to 110V. 1000W AC22-60V to 110V. Solar Grid Tie Inverter. 300W 10.8-30VDC to 110V/240V. 600W 22-60VDC to 110V. 600W 10.8-30VDC to 110V. 2500W Off Grid Inverter. We also have another THREE 500W Wind Power Grid Tie Inverter Versions, please check it. 500W Wind Power Grid Tie Inverter with DC Input Voltage Range 22-60V. 500W Wind Power Grid Tie Inverter with AC Input Voltage Range 10.8-30. 500W Wind Power Grid Tie Inverter with AC Input Voltage Range 22-60V. 500W Small Grid Tie Power Inverter. (with built-in Dump load controller, but not with dump load). Wind Turbine Generator Energy System. Works great for wind Turbines with. Output of 500 watts and under…. If you need 500 watts of wind inverter or AC input, please search it at our store. If you need solar power grid tie inverters, please search it at our store or contact me as you do not need the wind starter kit. This 500W micro grid tie inverter is designed specially for small wind energy system. This inverter can directly connect wind charger through inverter to home grid. It can maintain the rotating speed of the wind turbine and keep the voltage from the wind turbine always at the range of the rated range of the grid tie inverter. It also has a high voltage protection function, when the wind is too strong, and the dump load controlling system can not keep the output voltage from the wind turbine, the controller will disconnect itself from the wind turbine, so it is very safe to be used. Easy to installation, just need wind turbine, grid tie inverter, then directly can put into home grid. Features MPPT (Maximum Power Point Tracking) allowing each Wind turbine to run at optimum output. Normal AC Output Power. Maximum AC Output Power. Switch is at 115V Position. Total Harmonic Distortion(THD). 10.8V -30V DC (not AC). The small type grid tie power inverter can obtain the wind energy from wind generators and can tie to the grid through its output cable with no extra equipment. The installation is very convenient and reliable. The system which combines the small grid tie power inverter and the wind generator is konw as “SGTS”. The inverter can be connected to any outlet at home, as long as this line is run by the conventional electric network. The small grid tie monitors the volume, frequency and phase of the home grid, then product a pure sune wave that the frequency and phase are as same as the grid’s. 1, Connect Wind Turbines. Supply cables to the DC input terminal of the inverter, be sure that the polarity is correct. Recommended DC input cable size for maximum output is 8AWG or cables that can handle more than. Optimal length would be less than. Longer cables will experience higher voltage drop. The range of output power of wind generator is 20W500W. Connect the supplied AC power cord to the inverter and plug it to a home wall socket. 3, The 3 green LED indicators will start to cycle from left to right when the grid and DC supply is detected. This indicates the inverter is operating under normal condition. The rate of the cycling is according to how much power is being output from the solar panels or the wind turbine. The more big output power is, the more fast the rate is. If there is no AC grid detected, the red LED will be on, the inverter will not put out power, this is called Island Protection. The item “500W Wind Turbine Grid Tie Power Inverter AC 90V-130V Dump Load Controller 12VDC” is in sale since Monday, August 06, 2012. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “chargerdeal” and is located in South San Francisco, California. This item can be shipped to United States.

Model: SUN-500G-WDL
Type: Wind Grid Tie Inverters
MPN: Does not apply
Brand: masspower

Category: 500w | Comments Off

March 14

Wind Turbine Controller Grid Tie Inverter. Custom. One of a kind. Get more KW

Grid tie inverter switching controller. This controller can switch two different voltage grid tie inverters to get maximum wind power. Use a 250w GTI for low wind and 1000W 22-60GTI for higher winds. This controller can be set for switching from 0-90vdc by the user. It can also be used to switch from a battery bank to a grid tie inverter as well. Needs a constant 12vdc to operate. It has two real time meters that show AC and DC production. Amps, watts, voltage and Kwh. They each update ever second A Red led indicator light for switching activation. AC fuse 15a , DC fuse 1a for internal controls, and 1 duplex AC outlet to plug up to (2) grid ties into. Terminals for AC 120v input, 12vdc input, GTI DC input. 30 A rated terminals. Ties right off your wind turbine rectifier. Recommended 20amp 120vac hard wire dedicated circuit. Includes an 80amp 3 phase rectifier. If you are switching from batteries to grid tie i can build the system for that. You must tell me your full intentions so i can build the system to your needs. The box is made of ABS plastic for light weight mounting and cost effective but rigid. The controller is rated for 30amps at 60 vdc. I have tested (2) types on this system. Windy nation 750w turbine and a HYE. (HY Energy) 24V 1000W. The HYE is also know as a Wind Max or Sky Max. It will also allow your components to run cooler since it allows a higher voltage GTI to work in conjunction with the system. Higher voltage and less amps equals less heat and more power to harvest. If you are not savoy with electrical please consult with a licensed electrician. I assume now responsibilities on how you hook up this controller. I custom make each controller so you will have to specify your current system and type of wind turbine you have so we can make sure its the perfect controller for you. It takes about 4 weeks to custom build due to ordering components. Controllers may change in appearance however the listing for what is does is the same.. This is due to new R and D technology. This is a one of kind controller made in the USA. How it works: Set voltage dial from 0-90 v to switch between GTI’S. So lets say at 18v your system will switch from a 10-20vdc gti to a 22’60vdc GTI. This may happen at a 10mph wind. You will have to set up your switching peramiters according to wind speed vs volts. Once above the 18v the 10-30 GTI gets disconnected and allows the bigger GTI to take all the turbine power. Under 18v the 10-30 gti will reconnect. The main 22-60v GTI is always connected and the dump coil is connected to this GTI only. For a battery bank you must use a blocking diode so GTI does not take power from the battery bank. Set the voltage switch to your float voltage of lets say 14.1. The controller will disconnect the battery and send power only to the 22-60v GTI. Only two gti’s can be used. For a battery bank use a 12 or 24v bank The best efficiency system is a 24v ac output wind turbine at a 1000w with a 250w 10-30vdc input and a 22-60vdc input with the manufacture dump load resistor connected only to the 22-60v GtI For battery use a 12 v battery system replace the 250w10-30vdc GTI with the pos and neg from the batteries. Remember you can dial your switching at any voltage from 0-90vdc. Contact me with any questions on this one of a kind controller. Each controller is built one at a time due to them being custom made. It takes about 4 weeks to get parts. We build these by hand no fancy machinery. Every unit is hand crafted and tested. The item “Wind Turbine Controller Grid Tie Inverter. Custom. One of a kind. Get more KW” is in sale since Monday, March 14, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “llea6423″ and is located in Pottstown, Pennsylvania. This item can be shipped to United States, to Canada, to United Kingdom, DK, RO, SK, BG, CZ, FI, HU, LV, LT, MT, EE, to Australia, GR, PT, CY, SI, to Japan, to China, SE, KR, ID, to Taiwan, to Belgium, to France, to Hong Kong, to Ireland, to Netherlands, PL, to Spain, to Italy, to Germany, to Austria, RU, IL, to New Zealand, PH, SG, to Switzerland, NO, SA, UA, AE, QA, KW, BH, HR, MY, TR, BR, CL, CO, CR, PA, TT, GT, HN, JM.
Wind Turbine Controller Grid Tie Inverter. Custom. One of a kind. Get more KW

Category: wind | Comments Off

February 14

Wind Turbine Controller 0-90v input 60 amp Grid Tie Inverter switching system

Dump load controller made in the US for micro wind turbines. Made by a wind turbine installer. Features a 0-90vdc input to trigger an external 100 amp relay. The system must have a constant 12vdc to operate. Digital volt meter reads the turbine voltage. Rated at 100 vdc. No external power needed for the volt meter to work. LED indicator lights on the board for on/off operation. Rated for indoor use only. SSR’s burn out so i went with reliable mechanical relays. Most parts can be bought locally. Comes fully wired with 60 amp wiring. Only break to service the turbine, not in the middle of mid to high winds. Ties in parallel to your existing rectifier. Use it for dc switching dump loads or grid tie inverters or battery banks. Adds protection to your system. Hooking this system up in parallel to your existing wind turbine rectifier will not drain your battery bank as other dump load controllers do. This can also be used to switch grid tie inverters from battery to grid tie or from a lower grid tie inverter to a higher voltage grid tie inverter. The higher the voltage you dump the less amps you will be dumping. So a 1000w 48v wind turbine will need a dump load coil to handle a 1000w 48vdc wind turbine would calculate to the battery voltage of 52 battery volts divd. By 1000 w =19.2 amps. For a dump coil, even it out to 25 amps. The lower voltage you dump at the higher the amps are, as you can see below. 14 vdc x 60 amps = 840 watts (12 vdc battery system). 28 vdc x 60 amps = 1,680 watts (24 vdc battery system). 52 vdc x 60 amps = 3,120 watts 48 vdc battery system. Relay 12v coil 100 amp Dump load 60 amp max Volt meter 0-100vdc. Activates at 4 vdc for display Controller. 12Vdc power to remain on 0-90Vdc input to trigger external relay can be custom set with an external volt meter 1/10 scale. 5.1 v = 51 volt trigger ect. 3 dip switches for delay dumping 5 sec. Instant on off with no dip switches activated. I recommend at least one dip switch be turned on so the relay is not going on and off as much. That wears on the main relay. Normally open and normally closed options by using the built in switch Fuse protection. Dump coil not included. 80 amp rectifier with heat sink 60 amp wiring stranded AWG. 1/2 backer board with sheet metal cover for easy mounting components. Large 60 amp lugs for wire termination to dump coil or other device. All 60 amp lugs rated for Copper or Alumin. System activated uses 2 watts at time of switching. Do not input more then 90vdc in to the controller. This will destroy it. We will decide if a repair or replacement is needed. Must be in originol packaging. There are a lot of controllers out there that are junk and hype. My system is one of a kind and built from my trade experience. Every system is custom made just for you and tested before it leaves our shop. The item “Wind Turbine Controller 0-90v input 60 amp Grid Tie Inverter switching system” is in sale since Thursday, September 17, 2015. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “llea6423″ and is located in Pottstown, Pennsylvania. This item can be shipped to United States, to Canada, to United Kingdom, DK, RO, SK, BG, CZ, FI, HU, LV, LT, MT, EE, to Australia, GR, PT, CY, SI, to Japan, to China, SE, KR, ID, to Taiwan, ZA, TH, to Belgium, to France, to Hong Kong, to Ireland, to Netherlands, PL, to Spain, to Italy, to Germany, to Austria, RU, IL, to Mexico, to New Zealand, PH, SG, to Switzerland, NO, SA, UA, AE, QA, KW, BH, HR, MY, TR, BR, CL, CO, CR, PA, TT, GT, HN, JM.

Brand: Custom
Country/Region of Manufacture: United States

Category: wind | Comments Off

December 27

12V Charge Controller Fo PMA Wind Generator Air-X Ametek Solar GRID TIE INVERTER

Charge Controller For Solar & Wind Hybrid Systems. Item is located in our USA / Canada warehouse. Canadian buyers are required to pay GST/HST. Everything in the picture are included. Over the past few decades, as technology advances to improve our living, so does our demand for energy skyrockets. The usage of fossil fuel and nuclear energy has resulted in global warming, acid rain, melting of the polar cap and radiation pollution, it seems like investing in renewable energy is the only way to ensure our next generation will survive and prosper. Of all the different kinds of renewable energy available today, solar and wind are the two most popular ones favored by homeowners due to their. Easy implementation and wide range of suitable sites. With the micro solar grid tie application being simplified by our GP2-400 Grid Tie Inverter, many people have started to think about feeding wind energy back to the grid with the popular Air-X and other homemade turbines using the same concept. However, after some investigations are being done, they are disappointed to find out that connecting wind to the grid is a whole different story. As we know, solar has relatively stable throughput from dawn to dusk. On the other hand, wind is unstable and volatile. The major challenge presented with wind energy is sometimes it can go on for days without a breeze, and sometimes there are burst of gusts that are strong enough to damage systems. Obviously, todays equipments are not designed to handle this inconsistency and it seems like there is something missing to complete the puzzle. Fortunately, this missing puzzle has been found. Introducing GreenergyStars latest developed product: SolarWind Hybrid RX, the state of the art charge controller that can handle solar and wind at the same time! Since Air-X is a popular wind turbine in North America, our development team has specifically tailored this controller to work with the Air-Xs charging system. In addition, as requested by popular demand, this controller will also work with Solar Panels and other AC/DC wind Turbine. Installation Reference – not to scale (No inverter, batteries, turbines and solar panels included in this listing). What is a SolarWind Hybrid R X Charge Controller? GreenergyStar SolarWind Hybrid RX is he most advanced charge controller in the market today. Unlike other hybrid controllers, this multipurpose device is designed to work with Southwest Windpower’s Air-X, 403, and 303 plus other 12V AC/DC turbines and solar panels. The SolarWind Hybrid RX has utilized microprocessor based control electronics, sophisticated monitoring software, high quality finned aluminum casing and an intuitive LED display design. It is designed to work with the. GreenergyStar branded grid-tie inverters. To send renewable energy generated by Air-X, 12V AC/DC Turbine and solar panels back to the grid in a stable, controlled and safe manner. The following list will summarize its major features. Hybrid system designed to work with Southwest Windpower’s Air-X, 403, and 303 plus other 12V AC/DC turbines and 12V solar panels. Compatible with GreenergyStar branded grid-tie inverters. Maximum power: 1000W (rated at 27V & 37.5A). System Voltage: 12V Nominal (see input / output sections for range). Microprocessor based control electronics to control charging, outputs and dump load. Dump load utilize Pulse-width modulation (PWM) switching technology to recover power during high wind periods. Manual Braking switch to isolate wind turbine from the system. Intuitive LED Display to reflect system status. Keeps battery in an optimum charged state. Prevents overcharge and over-discharge. Internal diode to prevent reverse current to solar panels or wind turbine at night. High quality finned aluminum casing to protect the interior and dissipate heat. Operating voltage & current on all terminals: 11.5V 27V, 0A 37.5A. Maximum input voltage & current on all terminals: 30V , 40A. Withstand voltage: 35V (anything above will damage controller). Stand-by power consumption: 0.1W. AC Turbine : For 3 phase AC turbine. The 3 wires from AC turbine can be connected to the terminals in no specific order. Built in rectifier will convert AC to DC. Can also be connected here as the rectifier accepts DC input as well. LED will turn Green when there is an active input source. DC Turbine : Recommend for Air-X since this terminal has the. LED will not turn on since the Air-X has its own (red) charging LED. LED will turn on when there is power coming in from the inputs. Input Protection & Specification. Manual Turbine lock to force dump load to turn on. Pulse Width Modulated Dump Load. Stay-Online Feature to keep Air-X up and running in low battery condition. Night Time Reverse current protection to prevent current going into wind turbine and solar panels. Over current Protection (40A Fuse). Operating output current: 37.5A. Total maximum output current: 40A. Maximum current on individual output: 30A. Voltage tolerance: +/- 5%. Maximum Output Power: 1000W (rated at 27V & 37.5A). Output starts when inputs are above 12.5V. OUTPUT A, B, C. LED will turn Orange with respect to each output. Battery is an input and an output at the same time. LED will turn Blue indicating battery is being charged. Overcharge protection Cut off voltage: 14.7V. Over-discharge protection Cut off voltage: 11.4V. Recommend using deep cycle batteries if possible. Normal lead acid batteries are acceptable as well. 3 charging modes: Continuous charging, Pulsing, Trickiling. Mode 1 – Power Supply. When input voltages are lower than the battery’s voltage, the battery will act as a supply to all outputs. Power to all outputs will be cut when the battery has drop down to 11.4V. Mode 2 – Stay Online (for Air-X only). When battery voltage is below 11.4V and input voltages is under 9V, even though all outputs will be cut, the charge controller will still send electrical pulse to the DC input terminal every 5 – 10 seconds as indicated by the pulsing Red. This is necessary for Air-X’s internal controller to stay on. Since the Air-X will not wake up on its own, without these pulses, even if wind starts blowing the Air-X will free spin and no power will be generated. Warning: Controller will get. If polarity of battery is incorrect. Requires a minimum of 1.2Ohm 600W resistive load to be connected to the dump load terminal. Dump load activates when AC Turbine is >= 27V. Unlike conventional dump loads that short circuit on activation and drop outputs to zero, the SolarWind Hybrid RX utilizes Pulse-width modulation (PDM) switching technology to only dump what is necessary and conserve the rest. (refer to Figure above). Activating dump load will slow down the AC turbine and reduce voltage spikes. Over voltage protection: All outputs will be cut when input voltage is over 30V. However dump load will stay on. LED will turn Red when the dump load has been activated. Manual Turbine Lock (Brake). Manual Turbine Lock is used to force dump load to fully turn on (ie: short circuit). Useful when it is necessary to isolate AC wind turbine from the system (ie: during installation or maintenance). Turbine lock is the red switch at the top-left corner of the Output Face (refer to Figure 1 on page 6). ” 0 ” – unlocks turbine. 25’C – 85’C. Dimension (L x W x H). 19.3 x 13.1 x 6.9 cm 7.5″ x 5.2″ x 2.7. Wall Mount at base. Convection cooled with fan (activate around 50’C 60’C). High quality finned aluminum to act as heat sink for fast heat dissipation. The item “12V Charge Controller Fo PMA Wind Generator Air-X Ametek Solar GRID TIE INVERTER” is in sale since Wednesday, May 25, 2011. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “goodsgood” and is located in Blaine, Washington. This item can be shipped worldwide.

Energy Type: Wind

Category: charge | Comments Off

December 22

Grid Tie All In One Charge Controller Board with Aims Power Inverter

All In One Charge Controller Board. With 500 Watt Grid Tie Inverter. And 2500 Watt 24VDC Aims Power Inverter. This all in one charge controller board includes. (1) 440 Amp 10,000 Watt charge controller. (1) 200 amp fuse and holder. (1) 500 Watt Grid Tie Inverter. (1) DC to AC modified inverter 24 Volt 2500 Watt model. Completely pre-wired and ready to connect to your batteries with heavy duty fine stranded copper cable, tinned copper lugs, and dual wall heat shrink. Due to high customer demand, we’ve now added a 500 watt grid tie inverter as a diversion load. The grid tie inverter plugs into any 120 volt AC 60 hertz grid power connected wall receptacle (outlet). The DC to AC power inverter connects directly to your battery bank allowing you to power up 120 volt AC devices directly. In addition, the DC to AC Aims Power Inverter works as a’back-up’ or’stand-alone’ unit providing you with another source of free power whether the grid is working or not. Being able to run lighting, emergency equipment, and keeping your refrigerator cold when the grid is down is a valuable benefit! If you do not have grid power, see our other All In One Charge Controller Boards. For stand alone or remote power. We’ve made some important modifications to the assembly to make the grid tie inverter operate and to operate safely and reliably. The grid tie inverter alone cannot power devices directly. It must be plugged into a wall outlet connected to grid power. The optional DC to AC power inverter can, however. We recommend 250 to 1000 watts total of 24 volt solar charging panels on small or medium sized battery banks and up to 3,600 watts on larger battery banks. You can add additional grid tie inverters in parallel with the existing one. Do not exceed 1,500 watts of inverter output into any one wall outlet. The charge controller will come preset to disconnect the incoming solar power when the batteries are full therefore if the electric grid power is OFF you will not overcharge your batteries. This is important because the grid tie inverter must’see’grid power ON to feed power to it. The charge controller will still however go into a diversion cycle lasting up to 5 minutes each time. Because grid power is not 100% reliable. We are unable to allow the connection of wind turbines directly to this control board. However you may use an additional charge controller of suitable size and with its own diversion load to connect wind turbines to the same battery bank. This will help fill the batteries even faster and can provide valuable power at night. Even though the grid tie inverter is connected and prewired to the control board, it is not UL1741 listed. This controller board is simple to install, but, if in doubt, hire an electrician to help you. Below is an inside look at the All In One. Some of the key features of this controller are. Microprocessor controlled — This is very important for both stability and functionality. User changeable settings — Several controllers on the market set the dump level, and that’s that! Works directly with 12, 24 or 48 volt systems. – The relay contacts can handle open collector voltages of up to 120 volts. High Contrast LED battery voltage. Several controllers do not tell you what’s going on – This one does! High Contrast LED turbine amperage meter. Meters can be shut using the on/off switch. Two factory installed, fully wired D/C breakers and disconnects. Entire unit is wired and ready to go for both wind and solar. – Ever wonder if your controller & load are working OK? Large (8″ x 12″) solid steel enclosure, with multiple conduit knockouts. Large enough terminal blocks that you can actually terminate large wire See notes below. The electronics are fully isolated from the enclosure, no ground loops. Draws almost no energy while monitoring (all electronics must use some power, to work — this is a miser). Some specifics about the points made above. The microprocessor is the heart of the controller. It is given the battery voltage and the user changeable trip points. This information is analyzed and acted upon. The Battery level is checked, and based on that info. The Green LED flashes or is illuminated as follows. (One) Flash indicates the battery is less than 12 volts (12 volt system – Double for 24 etc). (Two) Flashes indicates the battery is 12 to 12.5V. (Three) Flashes indicates the battery is 12.6 to 13v. (Four) Flashes indicate the battery is 13.1 to 13.5V. (Five) Flashes indicates the battery is above 13.5V but less than 13.9V (Settings are adjustable). Steady green means the battery is full. The red LED is illuminated when the battery is being dumped at 14.5v or the charge source diverted. The dump remains active for a minimum of 5 seconds, at which time it is checked by the microprocessor. If battery voltage drops below the “Dump Cancel ” level, the dump is disabled, otherwise the dump is continued and rechecked every 5 seconds. Settings are user changeable! By simply turning a simple potentiometer with a small screwdriver, you can quickly adjust the trip point. – 10,000 watts!! — This is a MONSTER controller. 150 amp heat activated breakers have been installed to limit continuous current to 150 amps. Key features of AIMS 2500 Watt Power Inverter. 2500W max continuous power. Volt meter on front panel to monitor your battery voltage. Watt meter on front panel. LED indicator green/red that monitors ready/fault. Dual ac receptacle with protective rubber covers. Dual cooling fan operation Internally fuse protected. Ac output short circuit protection. Auto reset on most fault conditions. Aluminum case for optimal cooling. Pre-wired for remote on/off switch. Free 1 year tech support. This inverter is an excellent choice for our customers who currently have a 24 volt DC power source. AIMS offers all the great features found on the 12 volt version and includes them with this inverter. Some of these great features include digital bar graph style display gauges, thermally controlled fan, and isolated ground neutral. The display gauges offer immediate information regarding your inverter system. Dual bar graph style meters boast red, yellow, and green lights for a quick reference to your system’s condition. The cooling fans are thermally controlled and only operate when needed based on temperature. The design saves battery power since the fans will not run all the time. Whether you need reliable power for a bus/coach that has a 24 volt system or an off grid cabin that has a 24 volt battery bank connected to solar panels, this inverter is a great option. Continuous output power: 2500 Watts. Surge power capability (peak power): 5000 Watts. Use our 150 amp inline fuse. Dc input / operating voltage: 20 to 30 Volts. Output voltage: 120 Volts ac +/- 10%. Output wave form: modified sine wave with phase correction. Output frequency: 60 Hz +/- 1 Hz. Battery low voltage shutdown: 20.0 +/- 0.5 V. No load current: < 0.6 Amps. Full load efficiency: 90%. 1/3 load efficiency: 95%. No load minimum operating temperature: -15 degrees Celsius. Full load maximum operating temperature: 55 +/- 5 degrees Celsius (automatic shutdown). AC Output Socket Type: dual Type 2 -3 prong. High input voltage protection: 30V-34V. Low input voltage shutdown: 20V. UL maximum recommended per outlet 1500W. INSIDE OUR STORE MISSOURI WIND AND SOLAR IN SEYMOUR, MISSOURI. A REAL STORE WITH REAL PEOPLE. YOU CAN ACTUALLY COME IN AND TRY OUR PRODUCTS AND SEE THEM WORKING. It is your responsibility to pay them. Products may be slightly different than the ones pictured. If our supplier runs short of the products shown, we will substitute them for the same quality or better. The item "Grid Tie All In One Charge Controller Board with Aims Power Inverter" is in sale since Tuesday, April 21, 2015. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Wind Generators". The seller is "missouriwind" and is located in Seymour, Missouri. This item can be shipped worldwide.

Brand: Missouri Wind
Model: Grid tie all in one board with inverter
MPN: Grid tie all in one board with inverter
Country/Region of Manufacture: United States
Type: Wind Turbine and Solar Panel

Category: grid | Comments Off

December 2024
M	T	W	T	F	S	S
« Nov
						1
2	3	4	5	6	7	8
9	10	11	12	13	14	15
16	17	18	19	20	21	22
23	24	25	26	27	28	29
30	31