Output Power:300W, 500W, 800W, 1000W;For Home Station, Low Cost, Easy Intallation, For Monocrystalline Silicon. Directly connected to the solar panels (do not need to connect the battery). Using precise MPPT function, APL functions, the inverter automatically adjust the solar panels of maximum output power, simply connect the solar panel to the grid inverters. Do not need to connect the battery. AC 0 angle with high precision auto-detection. AC phase angle of 0 through isolation amplifier then input to the MCU for high-precision detection and analysis. The phase shift rate is less than 1%, thus achieve high-precision with phase modulation AC output together. In the process of the grid, usually adapt the same phase angle in parallel. Ie, When the two-phase alternating current total is equal to 0. Use switch to combination the two AC fusion and the product is rectified AC half-frequency AC to 100Hz first, then the machine use the high frequency current in the circuit and semi-100Hz frequency alternating current generated combination, to achieve high-frequency modulation. Pure Sine Wave Output. Use SPWM directly to make pure sine wave output. Automatic Sensing Function Solar Luminosity. Use the latest luminosity perception operation technology. The different illuminate angle and intensity of the solar panel will produce different current output. Use advanced CPU to operate the different illuminance and the data can be directly displayed on the LCD. Then you can visually see the sense of the strength of the sun unit. Power Automatically Locked (APL). In different current fluctuations, we should use the MPPT function. When the MPPT function adjusted to the maximum power point, the product automatically powers locked in maximum power point, then made the output power more stable. Maximum Power Point Tracking (MPPT). Because the current intensity and the voltage changes at any time, if there is no power point tracking, there will be a lot of problems. In the past time, usually adopt a solar controller, but this product uses high-precision MPPT operation power, automatic and immediate adjust the solar panels output power at the maximum output point, then achieve a stable output purposes. Automatically Adapt To Different Load Power Factor. Adapt to any of the power load. Constant Current, Constant Po. This product is constant current, constant output power, without any overload, over-current phenomenon. Automatically Shut Down When The Power Output Of a Fault. When the city power system is in failure, the inverter will automatically turn off the output. Multiple small power inverters in parallel can achieve large output power. High-Frequency High Conversion Rate. Adapt high frequency converter, the output more efficient. Recommend use solar panels. DC Maximum Input Power. Maximum output power factor. AC maximum output power. AC standard voltage range. Output short circuit protection. 099%(Indoor Type Design). Size (L x W x H). 21 x 16.5 x5.3cm. 31 x 16.5 x5.5cm. Package (L x W x H). Inner box:34x25x15.5CM. Inner box :43x25x15.5C. AC power cord length. 1 Red and 1 Green LED. Red terminal: Connect DC positive, black terminal: Connect DC negative. Show in Figure 1. AC socket: Connect to the mains. Put the side of the AC cord which has holes into the inverter with 3 foot outlet and the other side of the AC cord to home 3PIN AC outlet. Show in Figure 2. Figure 2 Figure 3. Switch: Connect the connections in right way, then turn on the switch. The inverter starts to work. Grid tied inverter used in the wind and solar street lights. Use this product, do not need to add solar panel controller, battery. Connection Method 1 (Figure 4 below). Method 2 (Figure 5 below). Wind energy, solar energy can supply to the grid at the same time, then achieve the highest efficiency. First consider this connection method. Use a large power generation capacity first. The other capacity is in added. Wind and solar capacity complement each other with moderate efficiency. In order to achieve higher power use requirements, this product can be stacked, such as: 4 grid inverter1000W stacking can achieve 4000W. And the number of the stacking is unlimited. Used as shown in Figure 6. Input voltage range: 10.5V to 28V. Solar Panel: Recommend using the power more than 30W and the standard voltage of 17.5V PV panels. Recommend using multiple solar panels. Solar panel in series will result in high-input voltage which will exceed the working voltage range of the inverter. Wind turbine system: Rated voltage 24VDC, maximum voltage 28VDC. Voltage range of the inverter whose output is 220V AC. Voltage range of the inverter whose output is 110V AV. Low-voltage protection (input DC voltage is less than 10.5VDC). Over-voltage protection (Input DC voltage is greater than 28.5VDC). Over-temperature protection when the chassis temperature is above 75’C. The temperature dropped about 2-10 minutes to restart automatically after cooling. Fault Protection (when 110VAC or 220VAC power outage or shutdown). Islanding protection: When the electric supply stop, the inverter automatically shut down output. Green LED flashing: The inverter is adjusting power output. MPPT is in working condition. Green LED long in time: The inverter is in working condition with the maximum output power. Please pay attention of the voltage when use the product. The voltage is from 10.528V, if is not these voltage the product may broken. Non-professionals do not disassemble. Only qualified personnel may repair this product. Please install inverter in the low humidity and well-ventilated place to avoid the inverter over-heating, and clear around the inflammable and explosive materials. When using this product, avoid children touching, playing, to avoid electric shock. Optimal length of the DC input line 8M or less, long cable will allow solar panels to the inverter. DC voltage drop caused by wear and tear. Connected to a power outlet to provide AC. Connected solar panels, battery or wind generators DC input DC power supply cable. –Proposed wind power plant with its own charge controller and load dump. Russian buyers were required to fill in the full name; Brazilian buyers are required to leave CPF/CPNJ Number; Chilean buyers are required to leave RUT number. All return products should be in original package with all accessories included. We stand behind our products so you are always covered! The item “300-1000W solar grid tie inverter, 10.5-28V DC, 120/230 AC, pure sine wave, mppt” is in sale since Thursday, June 08, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “sunhome910″ and is located in , . This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

• Brand: Ecopower
• MPN: Does Not Apply
• Country/Region of Manufacture: China