https://gridtieinverter.org Wed, 22 Apr 2026 00:02:49 +0000 en-CA hourly 1 https://wordpress.org/?v=4.1.1 https://gridtieinverter.org/2025/06/2000w-48v-solar-grid-tie-inverter-withlimiterrs485-pure-sine-wave-mppt-dc45-90v/ https://gridtieinverter.org/2025/06/2000w-48v-solar-grid-tie-inverter-withlimiterrs485-pure-sine-wave-mppt-dc45-90v/#comments Sat, 28 Jun 2025 15:59:03 +0000 https://gridtieinverter.org/2025/06/2000w-48v-solar-grid-tie-inverter-withlimiterrs485-pure-sine-wave-mppt-dc45-90v/













2000W 48V Solar Grid Tie Inverter w/Limiter+RS485 Pure Sine Wave MPPT DC45-90V. Good Preise & Top Service. Why we produced the GRID TIE INVERTER WITH LIMITER? It is in response to the overwhelming clamor from our customers for a product that can control the amount of power that the grid tie inverters (GTI) can generate so that the amount of excess power produced by the solar panels are reduced to insignificant levels, if not eliminated — because in some countries, the producer pays for the excess power it gives to the distribution grid. This is because the electric power meters (the one provided by the electricity provider in the area) are not aware of the direction of power flow. In other words it only adds even if power is exported to the grid, thus, the consumers will be charged for power even if it is given to the grid, and this is the problem. This is the 2nd generation grid tie inverter with limiter. But in case customer install inverter far away from the main circuit breaker, we also enable the 2nd GTIL work with stand-alone limiter, we call this-external limiter. For sure, the inerter can work under normal Grid tie-no limit mode, just set on the nice LCD and save your setting. New upgraded firmware enable battery or solar limiter current and power model. User can set the maximum output power of inverter, this can make the inverter work at cooler contition as user want and extend the lifespan of the inverter. User can set kick in/off voltage of the inverter which can flexible using with battery bank depend on users mind and can prevent battery bank from over discharged. Input DC Voltage Range:45V 90V. Peak power tracking voltage:50V-90V. AC Output Voltage Range:190VAC 260VAC. Output Wave Form:Pure Sine Wave. Dimensions (W x H x D):434x196x88 mm. Applied Standards:VDE-AR-N 4105:2018-11;DIN VDE V 0124-100:2020-06. How to use the Inverter? Standard Grid Tie Inverter Model. More than 1 unit inverters stackable. The Grid Tie inverter converts DC power produced by Solar Panels to AC, connects to the grid and feed all of the power available from the panels to the AC load. All excess power that is not needed by the load is then exported to the Grid. If the Grid fails, then the Grid Tie Inverter will turn off. When the Grid comes back on line. The Grid Tie Inverter will again supply power to the load and any excess power is exported to the Grid again. If the Solar Panel is producing less power and the GTI cannot deliver all the power needed by the load, then power will be supplemented by the Grid. Power Meters (Except smart meter) are not aware of the direction of Power flow. The user then pays for the power exported and delivered by the Grid. Using Grid Tie Inverter With Limiter Model. The Grid Tie Inverter with Limiter delivers only the power needed by the load and prevents delivering excess power hence avoids excess power in going back to the Grid. The heart of the Grid Tie Inverter with Limiter is the Limiter Module (LM). The LM continuously sampled the power needed by the load through the current sensor connected after the Main Circuit Breaker. The LM then will process the signal. It then sends signal to Grid Tie Inverter how much power to deliver to the load in real time. The user, after installing and connecting the GTIL correctly, need not do anything and the unit will do its work automatically. Installation of GTIL With Internal Limiter. This installation is not require an additional limiter module, Installation is much easier. Clamp the current sensor cable to the hot wire to measure the current, the internal limiter will auto detect the load power and control the inverter output power, excess power will be well controlled. External protective device including dc and ac SPD(Surge protection device), dc and ac breaker, etc is recommended to installed in the system. Limiter Setting on the LCD of the inverter. The GTIL include three working mode:Work as normal GTI without power limitation. Work under Internal limiter mode and Work under External limiter mode, Pls make your setting on the LCD and save it, details setting operation, pls read the GTI manual. 5 Battery Discharge Power Mode. 6 Limiter Module Specification. Clamp sensor- Max 100A. Clamp sensor signal- 5v AC max mA. DC signal Cable- 5v DC, max mA. 1 x Solar Grid Inverter with Limiter. Does not include WiFi module. 1 x Internal type Limiter clamp with sensor & 2m cable. 1 x English User Manual. If it exceeds one year, we still provide after-sales service, but the after-sales accessories need to be paid by yourself. We will reply to your message within 24 hours. You have requested a return and we will provide you with a free return.

]]> https://gridtieinverter.org/2025/06/2000w-48v-solar-grid-tie-inverter-withlimiterrs485-pure-sine-wave-mppt-dc45-90v/feed/ 0 https://gridtieinverter.org/2025/06/2000w-48v-wind-grid-tie-inverter-withlimiterrs485-pure-sine-wave-dc45-90v-ac220v/ https://gridtieinverter.org/2025/06/2000w-48v-wind-grid-tie-inverter-withlimiterrs485-pure-sine-wave-dc45-90v-ac220v/#comments Fri, 20 Jun 2025 16:27:39 +0000 https://gridtieinverter.org/2025/06/2000w-48v-wind-grid-tie-inverter-withlimiterrs485-pure-sine-wave-dc45-90v-ac220v/











2000W 48V Wind Grid Tie Inverter w/Limiter+RS485 Pure Sine Wave DC45-90V AC220V. Good Preise & Top Service. The test point should be at the DC side of the built-in rectifier of the inverter, but you can calculate from 3 phases of AC output voltage of the wind turbine to get the DC voltage, the formula is Vac = Vdc/1.732. For example, if the DC input voltage range of the inverter is 4590V, then the wind turbine’s output AC range of the should be 45/1.73290/1.732 = AC25.9V 51.96V. This model grid tie has designed for wind turbines that put out 3 phases AC voltage. It can maintain the rotating speed of the wind turbine and keep the voltage from the wind turbine always at the range of the rated range of the grid tie inverter. It also has a high voltage protection function, when the wind is too big, and the dump load controlling system can’t keep the output voltage from the wind turbine, the controller will disconnect itself from the wind turbine, so it is very safe to be used. Wind Grid Tie Inverter with Limiter Sensor, which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. The backlit LCD display gives you a clear picture of the inverter’s operating status. The status of errors will be displayed with red letters on the grid tie inverter LCD display. Easy installation, Can be paralleled on AC side. Overload protection, Anti-island protection, Short-circuit protection/Reverse polarity protection. For 110/120V US home appliances Devices. You can simply add a Transformer (not includes) which stepping down 220/240V AC power to 110/120V AC Power, then your 110V home appliances is also ok to use at the same time, this inverter can’t output 110V power, this is a Single-phase 220V output inverter. Ensure that you operate and use our products smoothly. We call a system combining with a small grid tie inverter and a wind turbine as “SGWT”. The small type of wind grid tie power inverter can obtain the wind energy from wind turbines and tie to the grid through its output cables with no extra equipment. The inverter can be connected to any outlets of the utility grid at the house. The small grid tie inverter monitors the volume, frequency, and phase of the home utility grid, producing pure sine wave AC power that the frequency and phase are the same as the grids. The small grid tie inverter puts out power when the home grid is on. When the AC wind turbine is rotating, and its output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produce power, and the grid tie inverter will change the power from the wind turbine to the home grid. When the total power of the electric appliance that is using in the house is larger than the output power of the inverters, this power from the inverters will be consumed in the house. This will slow down the power meter; otherwise, the difference of the output power of the inverter between the total used power of the appliance will go out from the house to the out grid. NOTE: Any DC power input is prohibited. The Advantage of Inverter. Directly connect to three phase wind turbine(48V AC Wind Turbine Generator). Plug and play, easy to install. Can be paralleled on AC side. Built-in dump Load controller. Each inverter need to pass twice testing (20 hours) before leaving factory. Wind Turbine Voltage Range:AC25.9V 51.96V. How to choose the correct wind AC output voltage? You can calculate from 3 phases of AC output voltage of the wind turbine to get the DC voltage, the formula is Vac = Vdc/1.732. Input AC/DC Voltage Range:45-90V. AC Output Voltage Range:90-260VAC. Peak Inverter Efficiency:92%. Power Factor:0.99. Output Wave Form:Pure Sine Wave. Over Current Protection:Yes. Over Temperature Protection:Yes. Reverse Polarity Protection:Yes. VDE-AR-N 4105:2018-11;DIN VDE V 0124-100:2020-06. Weight (Kg):7.48KG. Dimensions (W x H x D):43419688mm. Dump load resistor connection Terminal. This terminals will connect to the dump load resistor. AC socket, This socket will connect the inverter to the public grid via the AC cable. This terminals will connect to the wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Save the setting after you reconfigurate the working mode or backlight setting. Installing Sunshine Grid Tie Power System involves several key steps. Considering the total capacity of the grid tie power system that you need. Choosing applicable wind turbine for Sunshine Grid Tie Inverter. Selecting accessory for installation of the Grid Tie Power System. Selecting correct model of Sunshine Grid Tie Inverter. Installing wind turbine to suitable place. Installing Sunshine Grid Tie Inverter to suitable place. Connecting Sunshine Grid Tie Power System with cables and connectors. Three Phases Grid Tie Power System. For example, installing a 6KW grid tie power system to three phase utility grid. The diagram is shown in Fig. 8, we seperate 6KW power sytem to three power system units, every unit has 2KW power. Connecting every system unit to different phase, this canbalance all grid tie power to three phases of the utility grid. Fllow this way, you can install more large grid tie power system to three phases, justseperate the whole power system to three equal power system units. If it exceeds one year, we still provide after-sales service, but the after-sales accessories need to be paid by yourself. We will reply to your message within 24 hours. You have requested a return and we will provide you with a free return.

]]> https://gridtieinverter.org/2025/06/2000w-48v-wind-grid-tie-inverter-withlimiterrs485-pure-sine-wave-dc45-90v-ac220v/feed/ 0