February 28

2000W Grid tie inverter, DC45-90V, 230Vac, pure since wave inverter mppt

2000W Grid tie inverter, DC45-90V, 230Vac, pure since wave inverter mppt

2000W Grid tie inverter, DC45-90V, 230Vac, pure since wave inverter mppt
New tested and output verified. The item “2000W Grid tie inverter, DC45-90V, 230Vac, pure since wave inverter mppt” is in sale since Monday, February 27, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “920.dale” and is located in Watertown, Wisconsin. This item can be shipped to United States, to Canada, to United Kingdom, DK, RO, SK, BG, CZ, FI, HU, LV, LT, MT, EE, to Australia, GR, PT, CY, SI, to Japan, to China, SE, KR, ID, to Taiwan, ZA, TH, to Belgium, to France, to Hong Kong, to Ireland, to Netherlands, PL, to Spain, to Italy, to Germany, to Austria, RU, IL, to Mexico, to New Zealand, PH, SG, to Switzerland, NO, SA, UA, AE, QA, KW, BH, HR, MY, BR, CL, CO, CR, PA, TT, GT, HN, JM.
  • Brand: Ecopower
  • MPN: Does Not Apply
  • Country/Region of Manufacture: China

2000W Grid tie inverter, DC45-90V, 230Vac, pure since wave inverter mppt
Category: 2000w | Comments Off
February 27

2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V

2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V
2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V
2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V

2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V
LCD Display1500W Grid Tie Solar inverter 45V-90VDC Input 110VAC Output. The small type solar grid tie power inverter can obtain the solar energy from solar panel, and can tie to the grid through its output cable with no extra equipment. The installation is very convenient and reliable. We call the system combining with small solar grid tie power inverter and solar panels as SGPV. The system includes solar panels and small type grid tie power inverter. Solar panels can be mono silicon, polygon silicon, non-crystal film or any other material that can transform solar energy to electric energy. The power of grid tie inverter should be matched to the power of solar panels connected. So the power of SGPV is defined by its solar panels, it can be standardization according to the actual using. The inverter can be connected to any outlet at home, when this line run by the conventional electric network. The small grid tie monitors the volume, frequency and phase of the home grid, then produce a pure sine wave that the frequency and phase are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to control the output power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the sun shines, the PV panel will produces DC voltage, and the grid tie inverter will change the DC voltage to AC voltage and puts out power to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. On the LCD Panel of the inverter, there is one AC output socket, that will connect the AC output cable to home grid. The LCD display will display the grid AC voltage, current , active power and electric energy that conbined to the grid. Electric parameters measurement function (voltage, current and active power, electric energy). Running time function (record load cumulative working hours). Power down data save function (save the number of kWh, operation time). Large screen LCD display (display voltage, current, power, active power, cumulative running time). UP: Short press will display power, electricity, current and voltage in anti-sequence. DOWN: Short press will display power, electricity, current and voltage in sequence. BACK LIGHT: Short press will open or close backlight. Normal AC Output Power. Maximum AC Output Power. AC Output Frequency Range. Total Harmonic Distortion(THD). DC Input Voltage Range. No need return the original one for low-valued items. All return products should be in original package with all accessories included. We stand behind our products so you are always covered! Pleas message us if recipient address changes needed before we fulfill the order. Sorry, no local pickups available. The free listing tool. The item “2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V” is in sale since Friday, July 15, 2016. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “chargerangel” and is located in Hayward, California. This item can be shipped to United States, to Canada, to Mexico.
  • MPN: Does Not Apply
  • Brand: Mass power

2000W LCD Display MPPT Solar Grid Tie Inverter Pure Sine Wave DC45-90V TO AC230V
Category: 2000w | Comments Off
February 27

2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable

2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable
2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable
2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable

2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable
2000W Wind Turbine Generator Grid Tie Inverter AC 45-90V to AC 110V. The grid-tie inverter can transfer wind energy from wind generators directly into the home grid using no extra equipment. It can be connected to any outlet (conventional network) in the home. The grid-tie inverter controls the phase and the frequency and voltage of the power generated by the wind generator. It produces a pure sine-wave and matches that of the grid. This model grid-tie has build in bridge rectifier and dump load controller, it can maintain the rotating speed of the wind turbine and keep the voltage from the wind turbine always at the range of the rated range of the grid tie inverter. It also has a high voltage protection function, when the wind is too big, and the dump load controlling system cant keep the output voltage from the wind turbine, the controller will disconnect itself from the wind turbine, so it is very safe to be used. There are 5 terminals on the left side of the inverter, 3 red terminals will be connected to the three phase output from the wind turbine, and 2 black terminals will be connected to dump load resistors. There are 4 LED indicators, 3 green indicators and 1 red indicator, 3 green LED indicators will start to cycle from left to right when the grid and AC input supply is detected. This indicates the inverter is operating under normal condition. The rate of the cycling is according to how much power is being output from the wind turbine. The bigger the output power is, the faster the rate is. If there is no AC grid detected, the red LED will be on, the inverter will not put out power, this is called Island Protection. 45V 90V AC NOT DC. No need return the original one for low-valued items. All return products should be in original package with all accessories included. We stand behind our products so you are always covered! Pleas message us if recipient address changes needed before we fulfill the order. Sorry, no local pickups available. The free listing tool. List your items fast and easy and manage your active items. The item “2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable” is in sale since Monday, February 27, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “chargerangel” and is located in San Jose, California. This item can be shipped to United States, to Canada.
  • Brand: Mass power
  • MPN: Does Not Apply

2000 Watt 45-90VAC to 230VAC Grid Tie Power Inverter for Wind Turbine stackable
Category: watt | Comments Off
February 26

2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor

2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor

2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
For new energy products , we are more professional. NEW 2000W Wind Power Grid Tie Inverter. With dump load controller and resistor. -Max Efficiency:>92% MPPT Efficiency:99%. -AC 220V 230V 240V 50hz 60hz Automatic. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire solar power system. Overload protection , Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD<5%, PF>99%. Build in dump load function. Build in Limiter (internal type). Introduction of Sunshine Grid Tie Inverter for Wind Turbine. The Wind Grid Tie Power Inverter is the worlds most technologically advanced inverter for use in utility-interactive applications. This manual details the safe installation and operation of the The Wind Grid Tie Inverter. This integrated system maximizes energy harvest, increases system reliability, and implifies design, installation and management. The small type wind grid tie power inverter can obtain the wind energy from wind turbine, and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. We call the system combining with small grid tie inverter and wind turbine as SGWT. The system includes wind turbine and small grid tie inverter and installation kit, and some SGWT also will include controller, dump load resistor. The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to control the output. Power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these. Power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. Input Voltage Range 45-90vdc (test point is at the output of the inside rectifier) , Peak power tracking voltage: 50-90v , Max output power:2000w , Nominal Voltage Range: 185-265v , Max Efficiency:>92% , MPPT Efficiency:99%. If DC input type invert. Er , there is only two input connection terminato. Input AC/DC Voltage Range. AC Output Voltage Range. Dimensions (W x H x D). Note: this is 2000w wind power grid tie inverter with limiter. Wind power grid tie inverter —- 1pcs , 2. Dump load resistor —1pcs , 3. AC cable –1pcs , 4. Limiter sensor/clamp / cable —- 1 set. Wind Grid Tie Inverter Installation. Considering the total capacity of the grid tie power system that you need. The total capacity of the whole grid tie power system is according to your power consumption in the site that you want to install, or how much power that you want it to feed to the utility grid. Actually, the volume is just according to your willingness, because when the total power of electric appliances that are being used in the installation site is larger than the output power of the grid tie power system, these power from the system will be consumed in the site, this will slow down the power meter, otherwise, the difference of the output power from the system between the total used power of the appliances will feed to the utility grid. For example, if you want to install a grid tie power system in your house, you could decide the total power volume according to the total power the appliances that you use in your house, maybe the consumption of total energy in per day is about 5KWH, then you should realize the averaged speed of the wind in per day at your site, check the power to the speed of the wind curve from the specifications of the wind turbine, then you can estimate the average power that the wind turbine can generate, actually the real average power the wind turbine can generate at your side is not easy to estimate, you need to check the history data of the climate, because it will vary every day according to the climate, just assume a 1KW rated wind turbine is suitable for the grid tie power system that you plan to set, with this capacity of the system, it can supply all power consumption in whole year. When grid tie power system is working, sometimes, there is extra power feed to utility grid if the power from the grid tie system is larger than the power consumed by the appliances in your house, and sometimes will not when it is not larger. If you use a 1KW wind turbine, then we call the GTWT system is 1KW grid tie power system, of course, you can install 500W grid tie power system or 2KW grid tie inverter, even more large capacity or more small capacity grid tie inverter, it doesnt matter. The capacity is too big, you should consider the volume of AC system of your house can hold the feeded power. Choosing applicable wind turbine for Sunshine Grid Tie Inverter. The most kinds of specifications that the factories marked about the wind turbines. 1, Starting wind speed(m/s). 2, Cut-in wind speed(m/s). 3, Rated wind speed(m/s). 6, Safe wind speed(m/s). 7, Rated DC voltage. You need to choose a wind turbine that the rated power can meet the power consumption. When you choose a wind turbine, you also need to consider ahead what. Model gird tie inverter of SUN series you want to use. Wind turbines have two output type. One is AC output type, and another is DC output type, if the wind turbine is DC output type. It must be integrated with a rectifier. So if the wind turbine is AC output type, you should. Use WAL model of SUN series grid tie inverter, if the wind turbine is DC output type, then. You should use WDL model of SUN series grid tie inverter. Selecting accessory for installation of the Grid Tie Power System. The accessory for grid tie power system including. 1, Connecting cables will be connected with wind turbine and inverters. 4, Power meter(Optional). 5, Bracket for wind turbine installation(not included in this user manual). Selecting correct model of Sunshine Grid Tie Inverter. When finished step1 to step3, then you can select a correct model of SUN series inverter. If the wind turbine is DC output type, then you should choose WDL model inverters, and. The input DC voltage range of the inverter should fit the DC output voltage of the wind. Turbine, the rated power of the inverter should also fit the max. Power of the wind turbine. And the AC output of the inverter should fit the standard of AC utility grid. If the wind turbine is AC output type, then you should choose WAL model inverters. Factories dont supply the AC rated voltage, just supply DC rated voltage, so our WAL also. Supply the DC input range, please check the DC rated voltage of wind turbine should fit. The DC input range of the grid tie inverter. Installing wind turbine to suitable place. Installing the wind turbine of the SGWT to suitable location where the wind is strong enough. To drive the wind turbine. Warning: Please read the user manual of wind turbine before you install the wind. Turbine, dont install the wind turbine under high wind. Warning: Ensure using strong braket to fix the wind turbine to avoid the danger under. Warning: The blades of the wind turbine should be taken down before the hurricane is. Installing Sunshine Grid Tie Inverter to suitable place. Place the Grid Tie Inverter on a surface protected from direct sunlight, high. The inverter requires at least 150mm of clearance around itself for. The inverters are for indoor use, cant use at outdoor. You can use screws to fix. The inverter to the surface, because some models of Sunshine grid tie inverter have fans on. The bottom cover, so the surface should be flat. Connecting Sunshine Grid Tie Power System with cables and connectors. Connecting the Grid Tie Power System with Cables and Connectors. After finished from Step1 to Step6, you should connect the wind turbine and inverter with cables. And connectors to integrate the Sunshine Grid Tie System. Connect the ground terminal of the wind turbine to the NEC approved AC grounding electrode. Connect the grid tie inverters to the grounded racking using a grounding washer approved for the. The ground wire of the AC cables is connnected to the housing of inverter when the AC. Cables is connected to the inverters, so when the AC plug is inserted to the socket of AC outlet of. Utility grid in the house, the ground pin of the socket must be connected to the Earth ground. Connecting the wind turbine output cables after complete from Step1 to Step8. Warning: Before connect the wind turbine output cables to grid tie inverter, you should stop. The the rotating of the wind turbine just in order to avoid the sparkle when connect the cables. WAL model of grid tie invereter connected with AC output type of wind turbine. Connecting two 1000G2-WAL with a max. Power is 2KW wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. GAIA NEW ENERGY is your trusted partner for long term business. We arethe MANUFACUTER of the solar inverter. We are responsible forthe quality of the inverter. The inverter has 2 years guarantee. All return items must be in their original condition. Please do contact with us for return address, details and any other issues. It may not apply to countries with different tariff rules. Please leave us message if you have any question, we will reply in 24 hours, thank you! The item “2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor” is in sale since Sunday, February 26, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “new-power2010″ and is located in ShangHai. This item can be shipped worldwide.
  • Brand: SUN
  • MPN: SUN-2000G2WAL-R
  • Country/Region of Manufacture: China
  • Power Type: 3 Phase Wind Turbine/Generator
  • Dump Load Controller: Built-in
  • Dump load resistor: Included
  • Display: LCD
  • Max. Power Output: 2000w
  • Input AC/DC Voltage Range: 45-90v
  • AC Output Voltage Range: 185-265VAC auto
  • Output Frequency: 46Hz~65Hz
  • Standby Power Consumption: <0.5W
  • Total Harmonic Distortion: <5%
  • Peak Inverter Efficiency: 92%
  • Power Factor: 0.99
  • Output Wave Form: Pure Sine Wave
  • MPPT Efficiency: 99%
  • Over Current Protection: Yes
  • Over Temperature Protection: Yes
  • Reverse Polarity Protection: Yes
  • Anti-Island Protection: Yes
  • Stackable: Yes
  • Weight ( Kg): 5.9kg
  • Dimensions (W x H x D): 469x196x88mm
  • Featurer Function: Limiter

2000W Wind Power Grid Tie Inverter with Limiter / Dump Load Controller Resistor
Category: 2000w | Comments Off
February 26

Lot 4 Enphase M250-IG Grid Tie Micro Inverter M250-60-2LL-S22-IG FREE SHIPPING

Lot 4 Enphase M250-IG Grid Tie Micro Inverter M250-60-2LL-S22-IG FREE SHIPPING
Lot 4 Enphase M250-IG Grid Tie Micro Inverter M250-60-2LL-S22-IG FREE SHIPPING

Lot 4 Enphase M250-IG Grid Tie Micro Inverter M250-60-2LL-S22-IG FREE SHIPPING
(Latest model) Have few left from my project. Great units to have and produce FREE electricity for life and never pay any electric bill ever!!!!! Have some scratches and little dings. Please see the photos by zooming. The item “Lot 4 Enphase M250-IG Grid Tie Micro Inverter M250-60-2LL-S22-IG FREE SHIPPING” is in sale since Sunday, February 26, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “aeolos777″ and is located in California City, California. This item can be shipped to United States.
  • Brand: Enphase
  • Model: M250-60-2LL-S22-IG
  • MPN: 880-00058
  • Country/Region of Manufacture: China

Lot 4 Enphase M250-IG Grid Tie Micro Inverter M250-60-2LL-S22-IG FREE SHIPPING
Category: enphase | Comments Off
February 25

2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator

2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator
2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator
2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator
2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator
2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator

2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator
For new energy products , we are more professional. NEW 2000W Wind Power Grid Tie Inverter. With dump load controller and resistor. -Max Efficiency:>92% MPPT Efficiency:99%. -AC 220V 230V 240V 50hz 60hz. Low cost and easy installation. Directly connect to three phase wind turbine. Much better output waveform compare with similiar GTI. Improving the efficiency of the entire solar power system. Overload protection , Anti-island protection. Short-circuit protection/Reverse polarity protection. AC output voltage and current THD<5%, PF>99%. Build in dump load function. Introduction of Sunshine Grid Tie Inverter for Wind Turbine. The Wind Grid Tie Power Inverter is the worlds most technologically advanced inverter for use in utility-interactive applications. This manual details the safe installation and operation of the The Wind Grid Tie Inverter. This integrated system maximizes energy harvest, increases system reliability, and implifies design, installation and management. The small type wind grid tie power inverter can obtain the wind energy from wind turbine, and can tie to the grid through its output cables with no extra equipment. The installation is very convenient and reliable. We call the system combining with small grid tie inverter and wind turbine as SGWT. The system includes wind turbine and small grid tie inverter and installation kit, and some SGWT also will include controller, dump load resistor. The inverter can be connected to any outlets of utility grid at house. The small grid tie inverter monitors the volume, frequency and phase of the home utility grid, then produce pure sine wave AC power that the frequency and phase are as same as the grid’s, and the volume is a bit higher than the grid’s, then according to the current controlled PWM, to control the output. Power to the grid. The small grid tie inverter just puts out power when the home grid is on. When the wind turbine is rotating, and the output of the voltage is in the range of the rated input voltage of the inverter, the wind turbine will produces power, and the grid tie inverter will change the power from wind turbine to the home grid. When the total power of electric apparatus that are using in the house is larger than the output power of the inverters, these. Power from the inverters will be consumed in the house, this will slow down the power meter, otherwise, the difference of the output power of the inverter between the total used power of the apparatus will go out from the house to the out grid. Input Voltage Range:22-60vdc/45-90vdc (test point is at the output of the inside rectifier) , Peak power tracking voltage:25-60v/50-90v , Max output power:1000w , Nominal Voltage Range: 95-140v/185-265v , Max Efficiency:>92% , MPPT Efficiency:99%. Input AC/DC Voltage Range. AC Output Voltage Range. Dimensions (W x H x D). (1) (2) Dump load resistor connection Terminal. This terminals will connect to the dump load resistor. (3) AC socket, This socket will connect the inverter to the public grid via the AC cable. This terminals will connect to the wind turbine. Wind power grid tie inverter —- 1pcs , 2. Dump load resistor —1pcs , 3. AC cable –1pcs , 4. Wind Grid Tie Inverter Installation. Considering the total capacity of the grid tie power system that you need. The total capacity of the whole grid tie power system is according to your power consumption in the site that you want to install, or how much power that you want it to feed to the utility grid. Actually, the volume is just according to your willingness, because when the total power of electric appliances that are being used in the installation site is larger than the output power of the grid tie power system, these power from the system will be consumed in the site, this will slow down the power meter, otherwise, the difference of the output power from the system between the total used power of the appliances will feed to the utility grid. For example, if you want to install a grid tie power system in your house, you could decide the total power volume according to the total power the appliances that you use in your house, maybe the consumption of total energy in per day is about 5KWH, then you should realize the averaged speed of the wind in per day at your site, check the power to the speed of the wind curve from the specifications of the wind turbine, then you can estimate the average power that the wind turbine can generate, actually the real average power the wind turbine can generate at your side is not easy to estimate, you need to check the history data of the climate, because it will vary every day according to the climate, just assume a 1KW rated wind turbine is suitable for the grid tie power system that you plan to set, with this capacity of the system, it can supply all power consumption in whole year. When grid tie power system is working, sometimes, there is extra power feed to utility grid if the power from the grid tie system is larger than the power consumed by the appliances in your house, and sometimes will not when it is not larger. If you use a 1KW wind turbine, then we call the GTWT system is 1KW grid tie power system, of course, you can install 500W grid tie power system or 2KW grid tie inverter, even more large capacity or more small capacity grid tie inverter, it doesnt matter. The capacity is too big, you should consider the volume of AC system of your house can hold the feeded power. Choosing applicable wind turbine for Sunshine Grid Tie Inverter. The most kinds of specifications that the factories marked about the wind turbines. 1, Starting wind speed(m/s). 2, Cut-in wind speed(m/s). 3, Rated wind speed(m/s). 6, Safe wind speed(m/s). 7, Rated DC voltage. You need to choose a wind turbine that the rated power can meet the power consumption. When you choose a wind turbine, you also need to consider ahead what. Model gird tie inverter of SUN series you want to use. Wind turbines have two output type. One is AC output type, and another is DC output type, if the wind turbine is DC output type. It must be integrated with a rectifier. So if the wind turbine is AC output type, you should. Use WAL model of SUN series grid tie inverter, if the wind turbine is DC output type, then. You should use WDL model of SUN series grid tie inverter. Selecting accessory for installation of the Grid Tie Power System. The accessory for grid tie power system including. 1, Connecting cables will be connected with wind turbine and inverters. 4, Power meter(Optional). 5, Bracket for wind turbine installation(not included in this user manual). Selecting correct model of Sunshine Grid Tie Inverter. When finished step1 to step3, then you can select a correct model of SUN series inverter. If the wind turbine is DC output type, then you should choose WDL model inverters, and. The input DC voltage range of the inverter should fit the DC output voltage of the wind. Turbine, the rated power of the inverter should also fit the max. Power of the wind turbine. And the AC output of the inverter should fit the standard of AC utility grid. If the wind turbine is AC output type, then you should choose WAL model inverters. Factories dont supply the AC rated voltage, just supply DC rated voltage, so our WAL also. Supply the DC input range, please check the DC rated voltage of wind turbine should fit. The DC input range of the grid tie inverter. Installing wind turbine to suitable place. Installing the wind turbine of the SGWT to suitable location where the wind is strong enough. To drive the wind turbine. Warning: Please read the user manual of wind turbine before you install the wind. Turbine, dont install the wind turbine under high wind. Warning: Ensure using strong braket to fix the wind turbine to avoid the danger under. Warning: The blades of the wind turbine should be taken down before the hurricane is. Installing Sunshine Grid Tie Inverter to suitable place. Place the Grid Tie Inverter on a surface protected from direct sunlight, high. The inverter requires at least 150mm of clearance around itself for. The inverters are for indoor use, cant use at outdoor. You can use screws to fix. The inverter to the surface, because some models of Sunshine grid tie inverter have fans on. The bottom cover, so the surface should be flat. Connecting Sunshine Grid Tie Power System with cables and connectors. Connecting the Grid Tie Power System with Cables and Connectors. After finished from Step1 to Step6, you should connect the wind turbine and inverter with cables. And connectors to integrate the Sunshine Grid Tie System. Connect the ground terminal of the wind turbine to the NEC approved AC grounding electrode. Connect the grid tie inverters to the grounded racking using a grounding washer approved for the. The ground wire of the AC cables is connnected to the housing of inverter when the AC. Cables is connected to the inverters, so when the AC plug is inserted to the socket of AC outlet of. Utility grid in the house, the ground pin of the socket must be connected to the Earth ground. Connecting the wind turbine output cables after complete from Step1 to Step8. Warning: Before connect the wind turbine output cables to grid tie inverter, you should stop. The the rotating of the wind turbine just in order to avoid the sparkle when connect the cables. WAL model of grid tie invereter connected with AC output type of wind turbine. Connecting two 1000G2-WAL with a max. Power is 2KW wind turbine. The Inverter display can show many information, The main interface of the display and the icons explainations are show above. The inverter also integrate with internal limiter and external limiter function which can prevent excess power from going to the public grid. Select the internal limiter mode, inverter will work under limiter mode, output power of the inverter will be determined by load power. Select the external limiter mode, inverter need a external limiter module working with it. For more details about the limiter function, pls contact supplier. This function only useful with limiter type inverter. Notes: Save the setting after you reconfigurate the working mode or backlight setting. Notes: Battery Discharge Current Mode And Battery Discharge Power Mode are not developed yet. This interface will show the real time grid waveform. The grid voltage and frequency also will show in this interface. The energy interface will show the power generation curve everyday. Today KWH and Total KWH are also show in this page. In this interface, the display shows real time power, PV input voltage, inside temperature, date and time. Clock And Date Setting. Set the clock and date in this page, save the setting before exit. AC Output Current Waveform and PF Test Of 2000W Model. Tested 2000W model at nearly full load, Output current waveform shows good pure sine wave in oscilloscope, PF value also shows in good result, 99.8% PF value. 14 days no reason to return. Why to choose GAIA grid tie Inverters? Advanced patented technology, MPPT efficiency is higher. High-quality imported components, more stable quality, lower failure rate. Significantly longer life, more than 10 years. Each inverter need to pass twice testing (16 hours) before leaving factory. Combination of SGPV does not interact. CE ROHS SGS Certification. Please do not choose a cheap power inverter. Low-cost power inverter use low-quality components, low efficiency, poor stability. Poor quality power inverter might damage the appliances, and even cause fires and explosions. GAIA NEW ENERGY is your trusted partner for long term business. We arethe MANUFACUTER of the solar inverter. We are responsible forthe quality of the inverter. The inverter has 2 years guarantee. All return items must be in their original condition. Please do contact with us for return address, details and any other issues. It may not apply to countries with different tariff rules. Please leave us message if you have any question, we will reply in 24 hours, thank you! The item “2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator” is in sale since Tuesday, February 14, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “new-power2010″ and is located in ShangHai. This item can be shipped worldwide.
  • Brand: SUN
  • MPN: SUN-2000G2WAL-R
  • Country/Region of Manufacture: China
  • Power Type: 3 Phase Wind Turbine/Generator
  • Dump Load Controller: Built-in
  • Dump load resistor: Included
  • Display: LCD
  • Max. Power Output: 2000w
  • Input AC/DC Voltage Range: 45-90v
  • AC Output Voltage Range: 85-265VAC auto
  • Output Frequency: 46Hz~65Hz
  • Standby Power Consumption: <0.5W
  • Total Harmonic Distortion: <5%
  • Peak Inverter Efficiency: 92%
  • Power Factor: 0.99
  • Output Wave Form: Pure Sine Wave
  • MPPT Efficiency: 99%
  • Over Current Protection: Yes
  • Over Temperature Protection: Yes
  • Reverse Polarity Protection: Yes
  • Anti-Island Protection: Yes
  • Stackable: Yes
  • Weight ( Kg): 6.5kg
  • Dimensions (W x H x D): 434x196x88mm

2000W Wind Power Grid Tie Inverter for DC/AC 45V-90V 3 Phase windmill generator
Category: 2000w | Comments Off
February 25

SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw

SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw
SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw
SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw

SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw
This inverter is capable of 12000w with 3phase, 240v output. I’m looking to sell this inverter so I can invest in other efficiency measures for my very inefficient house insulation, windows, etc. This item is new, out of the box, with documentation and mounting brackets. From the SMA website. The new UL-certified Sunny Tripower TL-US is designed specifically to meet American requirements for mid to large-scale decentralized PV systems. With a peak efficiency of above 98 percent, OptiTrac Global Peak shade management, a DC input voltage range of up to 1000 volts this three-phase, transformerless PV inverter has everything needed to ensure high efficiency. A security the Sunny Tripower can offer, thanks, in part, to integrated arc fault detection. Equipped with two independent MPP trackers, the Sunny Tripower TL-US can be used in applications with input voltages of up to 600 and up to 1000 volts, offering enormous flexibility in the design of a PV system. Grid management functions are of course included as standard as well as the most cutting-edge communication and monitoring technology. The item “SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw” is in sale since Wednesday, February 22, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “gdcycle” and is located in Fall City, Washington. This item can’t be shipped, the buyer must pick up the item.
  • Brand: SMA

SMA Sunny Tripower 12000-TL-US Grid Tie inverter 12kw
Category: sunny | Comments Off
February 24

LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V

LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V

LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
LCD Display 1000W MPPT Solar Grid Tie Inverter Pure Sine Wave. DC22-65V – AC110V or 230V. This is the NEW GTI2 Model with enhanced display & menu features! This is the Blue model in USA Stock! Newly developed grid tie inverter(second generation) with different design structure, enable better and stable operation quality. With much better output pure sine waveform and better PF Value. This IS the brand that is well known for durability and function. These are US Stock and ships as soon as your order is received. Max input DC voltage. Peak power tracking voltage. 110vac or 230vac auto sensing. 47.5-51.5 for 50hz, 59.3-60.5 for 60hz. Just for AC output. Meets Standards (pending certifications). The item “LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V” is in sale since Monday, February 20, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “shore_distribution” and is located in Bayville, New Jersey. This item can be shipped to United States, to Canada, to United Kingdom, DK, RO, SK, BG, CZ, FI, HU, LV, LT, MT, EE, to Australia, GR, PT, CY, SI, to Japan, to China, SE, KR, ID, to Taiwan, ZA, TH, to Belgium, to France, to Hong Kong, to Ireland, to Netherlands, PL, to Spain, to Italy, to Germany, to Austria, RU, IL, to Mexico, to New Zealand, PH, SG, to Switzerland, NO, SA, UA, AE, QA, KW, BH, HR, MY, BR, CL, CO, CR, PA, TT, GT, HN, JM.
  • Brand: Masspower
  • Model: SUN-22-65-1000G2-LCD
  • MPN: SUN-22-65-1000G2-LCD
  • Country/Region of Manufacture: China

LCD Display 1000W Solar Grid Tie Inverter Pure Sine Wave DC22-65V AC110/230V
Category: display | Comments Off
February 23

8 count SMA DC Disconnect and Combiner Box for Solar Electric Grid Tie Inverter

8 count SMA DC Disconnect and Combiner Box for Solar Electric Grid Tie Inverter
8 count SMA DC Disconnect and Combiner Box for Solar Electric Grid Tie Inverter

8 count SMA DC Disconnect and Combiner Box for Solar Electric Grid Tie Inverter
New, unopened, factory sealed box. You will receive 8 count SMA DC Disconnect/Combiner Boxes in this offer. DC_Disc-IUS082311 1 / 4 Additional Information for Installation SMA DC-Disconnect Accessories for PV Inverters Version: 1.1 Mat. DB-DC-DISCON Please check the Installation Guide delivered with your Sunny Boy. If the Installation Guide version is earlier than 2.1 (for example 1.2 or 1.3), then please read this information carefully and follow the instructions below. If your Sunny Boy Installation Guide has the version 2.1 you may disregard this additional information. The SMA DC-Disconnect is a DC circuit breaker disconnecting the PV generator from the inverter. The SMA DC-Disconnect is NOT an AC circuit breaker. This Additional Information describes the wiring of the DC-Disconnect. This instruction does NOT replace the Sunny Boy Installation Guide. Pay attention to all operation and safety instructions listed in the Installation Guide of the Sunny Boy. The Installation Guide describes how to connect the DCDisconnect and provides information on the torque of the cable connection. AC Wiring with SMA DC-Disconnect The Sunny Boy 3000US and 4000US are suitable for the connection to a 208 V and 240 V grid. The Sunny Boy 5000US, 6000US and 7000US are suitable for the connection to a 208 V, 240 V and 277 V grid. L1 Connect the black L1 (AC line 1 or UNGROUNDED) wire to the terminal labeled L1 in the SMA DC-Disconnect L2 Connect the red L2 (AC line 2) to the terminal labeled L2 in the SMA DC-Disconnect. Only for 277 V: L2 terminal not used! N Connect the white N (AC line N) wire to the terminal labeled N in the SMA DCDisconnect. PE Connect the green-yellow AC equipment- ground wire to the PE terminal labeled in the SMA DC-Disconnect. SMA Solar Technology AG DC_Disc-IUS082311 2 / 4 Additional Information for Installation DC Ground Wiring With SMA DC-Disconnect Pay attention to all operation and safety instructions listed in the Installation Guide of the Sunny Boy. DC Wiring With SMA DC-Disconnect Pay attention to all operation and safety instructions listed in the Installation Guide of the Sunny Boy. A Connect the grounding electrode conductor with the grounding electrode. B Connect the PV generator grounding to the grounding electrode. Negative Grounding Connect the positive DC wires to the terminal labeled PV UNGROUNDED in the SMA DC-Disconnect. Connect the negative DC wires to the terminal labeled PV GROUNDED in the SMA DC-Disconnect. Positive Grounding Connect the negative DC wires to the terminal labeled PV UNGROUNDED in the SMA DC-Disconnect. Connect the positive DC wires to the terminal labeled PV GROUNDED in the SMA DC-Disconnect. SMA Solar Technology AG DC_Disc-IUS082311 3 / 4 Additional Information for Installation DC Wiring With Additional DC Distribution When combining strings outside of the SMA DC-Disconnect, and when the combined input of a single source circuit is greater than 15 A, use the terminal labeled COMBINED for the ungrounded conductor. DO NOT use the terminals 1 – 4 labeled UNGROUNDED in this case. For connecting the DC wires to the Sunny Boy, see Installation Guide of the Sunny Boy. Torque Values and Wire Sizes SMA DC-Disconnect Additional DC Source Circuit Note: This circuit will no longer be fused so additional DC source circuit fusing may be required in order to meet UL and NEC. Negative Grounding Connect the positive DC wire to the terminal labeled COMBINED in the SMA DC-Disconnect. Connect the negative DC wire to the terminal labeled PV GROUNDED in the SMA DC-Disconnect. Positive Grounding Connect the negative DC wire to the terminal labeled COMBINED in the SMA DC-Disconnect. Connect the positive DC wire to the terminal labeled PV GROUNDED in the SMA DC-Disconnect. Wire Size AC & DC Terminal Blocks 15 1.7 6 – 10 AWG Combined Terminal Block Spring Terminal Spring Terminal 6 – 10 AWG Grounding Electrode Conductor Block 15 1.7 6 – 10 AWG SMA Solar Technology AG DC_Disc-IUS082311 4 / 4 Additional Information for Installation AC Wiring in the Sunny Boy Pay attention to all operation and safety instructions listed in the Installation Guide of the Sunny Boy. L1 Connect the black L1 (AC line 1 or UNGROUNDED) wire of the SMA DCDisconnect to the terminal labeled L1 in the Sunny Boy. L2 Connect the red L2 (AC line 2) wire of the SMA DC-Disconnect to the terminal labeled L2 in the Sunny Boy. N Connect the white N (AC line N) wire of the SMA DC-Disconnect to the terminal labeled N in the Sunny Boy. PE Connect the green-yellow AC equipment-ground wire of the SMA DCDisconnect to the PE terminal labeled in the Sunny Boy. WE WILL USE ADDRESS ON FILE AT THE TIME OF CHECKOUT AND WILL NOT ACCEPT RESPONSIBILITY FOR ADDRESSES THAT ARE INCORRECT OR UNDELIVERABLE. PLEASE PAY FOR ITEMS WITHIN 7 DAYS OF ITEM CLOSING DATE. We are located 30 minutes from. Pay with Pay Pal. The item “8 count SMA DC Disconnect and Combiner Box for Solar Electric Grid Tie Inverter” is in sale since Thursday, February 23, 2017. This item is in the category “Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Chargers & Inverters”. The seller is “dualsportgirl” and is located in Nevada City, California. This item can be shipped to United States, to Canada, DK, RO, SK, BG, CZ, FI, HU, LV, LT, EE, to Australia, GR, SI, KR, ID, to Taiwan, ZA, TH, to France, to Hong Kong, to Germany, to Austria, to Mexico, SG, HR, MY, BR, CL, CO, CR, PA, TT, GT, HN, JM.
  • Brand: SMA
  • MPN: Does Not Apply
  • Country/Region of Manufacture: Germany

8 count SMA DC Disconnect and Combiner Box for Solar Electric Grid Tie Inverter
Category: count | Comments Off